Installation Instructions

ManualsBrandsPatriot Lighting ManualsChandeliersKassidy Black 4 Light Chandelier

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

P0234

For Pendant Hardware Package (included):

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Turn off the power at fuse or circuit box

Mounting Strap (A) Fixture Mounting

Screw(D)

Wire Connector (C)

For Pendant Installation Steps

Lock

Nut (F)

Canopy Cover Assembly

Ball Nut (G)

Upper Rod

Threaded Pipe

Middle Rod

Lower Rod

Socket

Glass Shade

Glass Holder

Outlet Box

House Ground Wire

Wire Connector(C)

Fixture Mounting Screw (D)

Mounting Strap(A)

Green Ground Screw(E)

Lock Nut(F)

Mounting Screw(B)

1. Thread two fixture mounting screws through the mounting strap, and

then secure with two lock nuts. Adjust the length of the fixture mounting

screws if necessary.

2. Attach the mounting strap to the outlet box by using two mounting screws.

3. Rod Connections:

a. Thread the fixture wire from the fixture through the lower rod, and

then secure the lower rod onto fixture using the threaded pipe.

b. Thread the fixture wire through the middle rod, and then secure

the middle rod onto the lower rod using the threaded pipe.

c. Thread the fixture wire through the upper rod, and then secure the

upper rod onto the middle rod using the threaded pipe.

d. Thread the fixture wire through the canopy cover assembly, and then

secure the canopy cover assembly onto the

upper rod using the threaded pipe.

Note: Length adjustable from 29" to 89".

Use fewer rods if shorter length

is desired.

4. Connecting the wires with wire connectors

as follows:

---Connect the black wire from the fixture to

the black wire from the power source.

---Connect the white wire from the fixture to

the white wire from the power source.

---Attach the fixture ground wire (usually green

insulation or bare wire) to the mounting plate

with the green ground screw. Then connect

it to the house ground wire with the wire

Connector.

5. Attach the canopy cover assembly to the

mounting strap by inserting the fixture

mounting screws, and then secure it with

two ball nuts.

171110

Green Ground

Screw (E)

Mounting Screw (B)

Main Fixture

Set Screw

Cord

Vintage Bulb Max.60W

(not included)

Summary of content (4 pages)

PAGE 1
P0234 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
PAGE 2
6. Reel out the cord carefully from the main fixture to Adjust the length of cord you need. 7. Install 3 x 60W max medium base vintage bulbs (included) to the sockets. Fig. 1 Support Brace 8. Unscrew three set screws from the glass holder. Hold the socket into the glass shade, thread the three set screws through each holes of glass shades, and then secure them into the glass holder. Outlet Box Canopy 9. Repeat with the other glass shade. Coupling Kit 10.
PAGE 3
. Thread two headless screws through the mounting plate, and then secure them with four lock nuts (two on each side of the mounting plate). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level. 4. Attach mounting plate to the outlet box using two mounting screws. 5. Connecting the wires with wire connectors as follows: ---Connect the black wire from the fixture to the black wire from the power source.
PAGE 4
For Wall Light A: 32-1/2" B: 36-1/2" C: 9" For Pendant A: 32-1/2" B: 89" 171110