Specifications

ManualsBrandsPaxton Manualshome security & automationNet2 PaxLock Mifare 72mm

Page 1

12/11/2012

Parts list

Tools List

Power Drill

Drill bits 10 mm, 16 mm

Philips screwdriver

Small at blade terminal screwdriver

Pencil

4mm Allen key (supplied)

Technical Support

Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)

Saturday from 09:00 - 13:00 (GMT)

01273 811011 support@paxton.co.uk

Ins-30169 Net2 PaxLock Mifare

Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/

Net2Air Site Surveyor (690-200).

This access control unit uses wireless

communication. It is recommended that a

Net2Air site surveyor is used to determine the

best position for the bridge and control units.

This wireless unit requires a Net2Air bridge

to communicate with the server PC.

Paxton

5 6

1) Front Lock Assembly

2) Rear Lock Assembly

3) Door Handle x 2

4) Mounting screw ( short ) x 2

5) Mounting screw ( medium ) x

6) Mounting screw ( long ) x 2

7) 8 mm Spindle

8) AA battery x 4

9) 4 mm Allen Key

This unit requires Net2 v4.23 or later software.

Call Technical Support if you require advice.

Summary of content (7 pages)

PAGE 1
2/11/2012 Paxton Ins-30169 Net2 PaxLock Mifare Technical Support 01273 811011 support@paxton.co.uk Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT) Saturday from 09:00 - 13:00 (GMT) Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/ This wireless unit requires a Net2Air bridge to communicate with the server PC. Net2Air Site Surveyor (690-200). This access control unit uses wireless communication.
PAGE 2
Installing the hardware Step 1 - Marking out 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 Ø 16 105 Paxton 37 Ø 10 75 The lock case and cylinder (not supplied) must first be fitted to the door, ensuring that a 22-24 mm diameter hole is drilled for the follower (As shown on the template provided). Slide the spindle through the lock to allow the template to locate over it.
PAGE 3
Step 5 - Mounting on the door Present the front lock assembly to the door passing the wiring harness through the 16 mm hole. Present the rear lock assembly to the door and join the two parts together with the two mounting screws. Mounting Short Med Long - screws are provided in three lengths. Door width 35 mm to 45 mm Door width 40 mm to 50 mm Door width 45 mm to 60 mm Step 6 - Wiring Plug the wiring harness into the socket in the rear lock assembly.
PAGE 4
Step 10 - Fitting the handles Fit the two handles and secure with the grub screws provided. Check the mechanical operation of the lock and that the handles operate freely. Software installation The Net2 software should be loaded on the controlling PC and at least one Net2Air bridge configured to communicate with the unit. Full documentation is supplied with the Net2Air bridge unit and also on the website as follows: XAN1051 - Installing Net2 software < http://paxton.
PAGE 5
Software Configuration Door name: Name the Door. Door open time: Set the door open time. Unlock the Door during: Holds the door unlocked during this timezone. - Set to 'At No Time' for normal user operation. Reader: Local settings for the reader. Output: Configures the lock for timed release or toggle mode. Alarm: Enables/Disables the door alarm functions. (requires contact switch) Events: Shows the events for this control unit only. Access Rights: Lists users who have access through this door.
PAGE 6
Sleep mode The PaxLock is a standalone unit and stays asleep while there is no user activity. The Net2 server cannot wake up the unit. If the PIR is activated or the front button is pressed, it powers up the reader circuits in readiness for a token read. Should nothing occur within 3 seconds, the unit will go back to sleep. If a token is read, then the PaxLock moves into full operation.
PAGE 7
PaxLock reset The PaxLock holds address information for the bridge that it is bound to. This will cause problems if the unit is to be used on another system. The unit requires a hardware reset to clear its bridge information. This is achieved as follows: 1. Remove the inside handle from the door by loosening the securing grub screw. 2. Remove the cover by holding the bottom edge and pulling it towards you. The cover will lift off at the top when the bottom edge is clear of the housing. 3.