User manual

1. Press the OK Key [MENU], select Settings & Tools and press the OK
Key, scroll to Tools and press the OK Key, scroll to Voice Commands
and press the OK Key.
2. Press the Right Soft Key [Settings], scroll to Sensitivity and press
the OK Key.
3. Scroll to select Most Sensitive, Recommended or Least
Sensitive and press the OK Key.
ADAPTATION
Voice Command is speaker independent, which means that no training or adaptation
is required. Some users with heavy accents or unusual voice characteristics may find
difficulty in achieving high accuracy with speaker independent Voice Command, so the
Adapt Voice feature allows users to dramatically improve the recognition accuracy through
adaptation. Users who get acceptable recognition accuracy will find no additional benefit
to performing the Adapt Voice adaptation.
1. Press the OK Key [MENU], select Settings & Tools and press the OK
Key, scroll to Tools and press the OK Key, scroll to Voice Commands
and press the OK Key.
2. Press the Right Soft Key [Settings], scroll to Adaptation and press
the OK Key.
3. Scroll to select Adapt Voice or Reset Voice and press the OK Key.
To activate press the OK Key.
• Adapt Voice: Requires that you make recordings of your voice to customize
the voice recognitions system. It will take a few minutes.
• Reset Voice: Once you finish the adaptation process, you can reset the
adaptation to the factory default settings.
Reset Voice menu option only appears after you finish the Adapt Voice
process.
4. Wait for the beep and then repeat the sentences using a normal
tone of voice.
5. Repeat steps 1 - 4 when you are finished with a full session, you will
reach a screen that reads Adaptation Complete.
PROMPTS
Allows you to select the voice command system characteristics.
1. Press the OK Key [MENU], select Settings & Tools and press the OK
Key, scroll to Tools and press the OK Key, scroll to Voice Commands
and press the OK Key.
2. Press the Right Soft Key [Settings], scroll to Prompts and press
the OK Key.
78 Chapter 5 − Menu Function
Voice ToolsVoice Tools
3. Scroll to select Mode or Audio Playback and press the OK Key.
• Mode: Select the voice command system mode from the following:
- Prompts: Read out voice command prompts.
- Readout: Read out prompts, dialing digits and menus.
- Tones Only: Prompt you with a tone only.
• Audio Playback: Allows audio playback to play through the speakerphone
or through the earpiece. Scroll to select Automatic, Speakerphone or Earpiece
and press the OK Key.
CALL ALERT
Provides audible readout of the phone number and/or name (if in your contact list) of
an incoming call.
1. Press the OK Key [MENU], select Settings & Tools and press the OK
Key, scroll to Tools and press the OK Key, scroll to Voice Commands
and press the OK Key.
2. Press the Right Soft Key [Settings], scroll to Call Alert and press
the OK Key.
3. Scroll to select either Ring Only, Caller ID + Ring or Name
Repeat and press the OK Key.
ABOUT
1. Press the OK Key [MENU], select Settings & Tools and press the OK
Key, scroll to Tools and press the OK Key, scroll to Voice Commands
and press the OK Key.
2. Press the Right Soft Key [Settings], scroll to About and press the
OK Key.
3. The Nuance version appears.
4. Press the OK Key to return to the previous screen.
CALCULATOR
Allows you to perform simple mathematical calculations.
USING THE CALCULATOR
1. Press the OK Key [MENU], select Calculator and press the OK Key.
2. Follow the instructions below to calculate 8×6÷4-2.5=9.5
Directional
Key
right
Directional
Key
down
Directional
Key
left
Directional
Key
up
OK Key
×÷+=
Menu Function − Chapter 5 79
ToolsTools
090204_CDM8975_RAP_EN_REV02.indd 78-79090204_CDM8975_RAP_EN_REV02.indd 78-79 2009.2.9 2:8:56 PM2009.2.9 2:8:56 PM