Manual

ManualsBrandsPDR Mounts ManualsAccessories for videopdm110t

M odel

Thank you for purchasing the PDR panel display wall mount.

To ensure the correct usage, please read and follow the instructions

manual thoroughly. Please store the instructions in a safe place

for future reference.

To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight of both the panel

display and the wall mount.

Always use at least two persons for all installations.

Fully tighten all of the mounting screws as specified in the installation instructions.

Parts Configuration Chart Features

MOUNTING ARM ASSEMBLY

Special techniques are necessary for installation of the panel display mount.

Do not attempt to perform this work by yourself.

Request an installation specialist to install this unit.

Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.

Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for the

mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat and

airflow.

Low profile 2 5/8”

16" or 24" stud mounting points ( MODEL #110 )

Easy installation

Flat to 15 deg tilt (no tools required)

Lateral movement from center for better viewing position

Wall mount bracket…1 pc

5 mm x 16 mm

5/16" x 2 1/2” Lag bolts …4 pcs

Display bracket .... 2 pcs

6 mm x 16 mm

5/16" Flat washers…4 pcs

A rm Hook....2 pcs

P lastic Tri Knob ... 2 pcs

Plastic Washer...6 pcs

1 /4-20 x 5/8” Carriage Bolt... 2 pcs

1 /4-20 x 5/8” THPM Screw...2 pcs

1 /4” Starr Washer... 2 pcs

1 /4-20 nylock nut... 2 pcs

8 mm x 20 mm

Model # 110 = 32” Model # 120 = 24”

Square multi-mount washers...4 pcs

Model # 110 = 20” Model # 120 = 14”

See Model

Fig 1

All PDR mounts and adapters carry a limited lifetime warranty from ship date against defects in material and workmanship.

We are not liable for improper installation that results in damage to mounts, adapters or presentation equipment.

Mounts by

A division of David Engineering & Mfg. Inc.

PDM 110/120T PANEL DISPLAY MOUNT

Locking bar... 1 pc

SEE MODEL #

LEFT HAND SHOWN RIGHT HAND OPPOSITE

Assemble left and right arms per fig 1

Model #110

Model #120

5mm x 40

6mm x 40

8mm x 40

Plastic spacer 3/4 x 1”...4 pcs

4 mm x 16

4mm washer

TOP

BOTTOM

Summary of content (4 pages)

PAGE 1
Mounts by A division of David Engineering & Mfg. Inc. Model PDM 110/120T PANEL DISPLAY MOUNT Thank you for purchasing the PDR panel display wall mount. To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference. All PDR mounts and adapters carry a limited lifetime warranty from ship date against defects in material and workmanship.
PAGE 2
INSTALLATION LOCATION WARNING The wall where the wall mount is to be installed must be capable of long-term support of the total load of the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to withstand the force of earthquakes, vi bration and other external forces. Note: Incorrect installation can cause the p anel display to fall and cause injury.
PAGE 3
1. FASTEN MOUNTING PLATE TO WALL The bracket must be secured to the wall studs capable of holding at least (4) times the weight of the unit. The wall bracket should be mounted at the same horizontal center line as the display center line ( viewing horizontal center line). Using the four lag bolts( E ) and washers supplied ( D ) Level and secure the mounting plate to the center of the wall studs Pre drill 3/16” (5mm) hole for lag bolts fig.2 Fig 2 Model # 120 Model # 110 24 " 4.
PAGE 4
3. MOUNT THE DISPLAY TO THE WALL MOUNT BRACKET Lift the display with the brackets attached, onto the wall plate. See Fig4 Position the top and bottom into the slots. See fig 5 and Fig 6 Insert the locking bar (C) as shown in fig 5 with the locking holes facing up to match the holes in the wall mount bracket (B) . Make sure the display brackets engage the rails on the wall mount bracket (B) See fig 5.