PV 215 EQ Graphic Equalizer ® For more information on other great Peavey products, visit your local Peavey dealer or go online to www.peavey.
WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
SICHERHEITSHINWEISEACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen.
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions. 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6. N’utilisez qu’un tissu sec pour le nettoyage de votre unité. 7.
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela seca. 7. No bloquear ninguna de las salidas de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
警告: 電気製品を使用するときは、次の項目を含め、基本的な注意事項を常にお守りください。 1. 本書の指示内容をお読みください。 2. 本書は保管してください。 3. すべての警告に注意してください。 4. すべての指示に従ってください。 5. 本装置を水の近くで使用しないでください。 6. お手入れには乾いた布をお使いください。 7. 開口部をふさがないでください。 メーカーの指示に従って設置してください。 8. ラジエータ、 ストーブなど (アンプを含む)、発熱体の近くに設置しないでください。 9. 分極プラグや接地プラグの安全性を損なわないようにしてください。分極プラグの2つのブレードは、一方が他より幅広くなっています。 接地式のプラグには2つのブレードと接地プラグがあります。幅広のブレードや接地プラグは安全のために付けられています。所定のプ ラグがコンセントなどに合わない場合、 旧式のコンセントなどの交換について技術者に問い合わせてください。 10.
Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. ENGLISH Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
ENGLISH PV®215EQ Graphic Equalizer Description Thank you for purchasing a Peavey Electronics PV 215EQ graphic equalizer. The PV 215EQ is a dual-channel EQ incorporating Peavey’s legendary low-noise, low-distortion design. Ruggedly constructed, PV 215EQs have center-detented fader controls, with ±12 dB gain and an LED display indicating level. Other features include balanced inputs and outputs and bypass switches.
F R O N T PA N E L 3 3 6 5 4 2 1 LEVEL LED METER (1) This LED array indicates level from –12 dB to +17 dB. LEVEL CONTROL (2) This control regulates overall level of the EQUALIZER SECTION. Unity gain throughout the signal chain can be maintained by recovering lost signal gain at this point. The equalization process may result in noticeable signal loss. To compensate for this loss, engage the BYPASS switch (5) and compare the signal level with that of the equalized level.
R E A R PA N E L 10 9 10 9 8 7 IEC MAINS CONNECTOR (7) This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly.
PV ®215EQ Graphic Equalizer SPECIFICATIONS Channels: 2 Connectors: XLR balanced inputs and outputs Bands: 15 per channel Frequency Centers: 31.5 Hz, 40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz Input Impedance: 20k ohms Output Impedance: 1.5k ohms Maximum Output Level: 11 VAC Level Control: +/- 12 dB Signal to Noise: 90 dB Distortion: 0.
DEUTSCH PV®215EQ Graphic Equalizer Beschreibung Vielen Dank, dass Sie sich für den Graphik-EQ PV 215EQ von Peavey Electronics entschieden haben. Der PV 215EQ ist ein Zweikanal-EQ in Peaveys legendärem geräusch- und verzerrungsarmen Design. Die robusten PV 215EQs besitzen in der mittleren Position einrastende Fader-Regler und bieten ±12 dB Verstärkung und ein LED-Display zur Anzeige des Pegels. Weitere Merkmale sind symmetrierte Ein- und Ausgänge und Bypass-Schalter.
VORDE RSEITE 3 3 6 5 4 2 1 LED-PEGELMESSER (1) Diese LED zeigt den Pegel von -12 dB bis +17 dB an PEGELREGLER (2) Mit diesem Regler lässt sich der Gesamtpegel der EQUALIZER-STUFE einstellen. Die Leistungsverstärkung der gesamten Signalkette kann durch die Rückgewinnung von verlorenem Signal-Gain erhalten werden. Der Abgleich kann zu einem spürbaren Signalverlust führen. Um diesen Verlust auszugleichen, drücken Sie den BYPASS-Schalter (5) und vergleichen den Signalpegel mit dem abgeglichenen Pegel.
RÜCKSEITE 10 9 10 9 8 7 IEC-NETZSTECKER (7) Hierbei handelt es sich um einen genormten IEC-Netzstecker. Ein Wechselstrom-Netzkabel mit dem entsprechenden Wechselstromstecker und den entsprechenden Werten für die erforderliche Betriebsspannung liegt bei. Der Erdungsstift eines Geräts darf keinesfalls entfernt werden. Er ist zu Ihrer Sicherheit vorhanden. Fehlt der Erdungsstift an der verwendeten Steckdose, muss ein geeigneter Erdungsadapter verwendet und die dritte Ader korrekt geerdet werden.
PV ®215EQ Graphic Equalizer TECHNISCHE DATEN Kanäle: 2 Stecker: Symmetrierte Ein- und Ausgänge (XLR) Bänder: 15 pro Kanal Frequenzmitten: 31.5 Hz, 40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz Eingangsimpedanz: 20k ohms Ausgangsimpedanz: 1.5k ohms Maximaler Ausgangspegel: 11 VAC Pegelregler: +/- 12 dB Rauschabstand: 90 dB Verzerrung: 0.
FRANÇAIS PV®215EQ Egaliseur graphique Description Merci d’avoir choisi l’égaliseur graphique PV 215EQ de Peavey Electronics. Le PV 215EQ est un égaliseur 2-canaux dans la lignée des produits Peavey, avec de faibles niveau de bruit et taux de distortion, le tout dans une unité de construction solide et pratique.
PA N N E A U AVA N T 3 3 6 5 4 2 1 LEDs DE NIVEAU (1) Cet arrangement de LEDs vous indique le niveau entre –12 dB to +17 dB. CONTROLE DE NIVEAU (2) Ce contrôle vous permet de réguler le niveau de votre signal dans la section égalisation. La notion de gain unitaire est très importante pour tout appareil de traitement/diffusion de signal. Le procédé d’égalisation peut résulter en une perte de gain générale, qui peut être compensée par ce contrôle.
PA N N E A U A R R I E R E 10 9 10 9 8 7 CONNECTEUR D’ALIMENTATION IEC (7) Ce connecteur d’alimentation est au standard IEC. Un cordon aux spécifications adaptées est inclu dans le carton d’emballage. Toujours relier votre unité à une prise munie d’une connexion à la terre, et celle-ci correctement reliée au circuit électrique. Le fusible principal de votre unité est incorporé dans ce connecteur.
PV ®215EQ Egaliseur Graphique SPECIFICATIONS Canaux: 2 Connecteurs: entrées et sorties XLR symétrisées Bandes: 15 par canal Fréquences de Filtres: 31.5 Hz, 40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz Impédance d’entrée: 20k ohms Impédance de sortie: 1.5k ohms Niveau maximum de sortie: 11 VAC Contrôle de gain: +/- 12 dB Rapport signal/bruit: 90 dB Distortion: 0.
ESPAÑOL PV®215EQ Ecualizador gráfico Descripción Gracias por adquirir un ecualizador gráfico PV 215EQ de Peavey Electronics. El PV 215EQ es un EQ de doble canal que incorpora el diseño legendario de Peavey de bajo ruido y baja distorsión. De construcción robusta, los PV 215EQs tienen faders de control dentados en el cento, con ±12 dB de ganancia y un display LED indicador de nivel. Además incluye entradas y salidas balanceadas y conmutador de bypass.
PA N E L F R O N TA L 3 3 6 5 4 2 1 MEDIDOR LED DEL NIVEL DE SALIDA (1) Esta serie de LEDs indica el nivel de salida de –12 dB a + 17 dB. CONTROL DE NIVEL (2) Este control calibrado regula la ganancia general de la SECCIÓN DEL ECUALIZADOR. La ganancia unitaria a través de la cadena de la señal se puede mantener recuperando la ganancia de la señal en este punto. El proceso de ecualización puede dar como resultado una pérdida de señal perceptible.
PA N E L T R A S E R O 10 9 10 9 8 7 CONECTOR PRINCIPAL DE CORRIENTE (7) Este es un conector de corriente IEC estándar. Un cable de CA con los requisitos necesarios de voltaje y el enchufe apropiado se incluye en el paquete. Nunca retire la tercera patilla de tierra de ningún aparato. Esta ha sido incluida por su seguridad. Si la fuente de corriente no cuenta con una conexión de tierra, se debe utilizar un adaptador con tierra y el tercer contacto debe ser aterrizado propiamente.
Ecualizador Gráfico PV ®215EQ ESPECIFICACIONES Canales: 2 Conectores: Salidas y entradas XLR balanceadas Bandas: 15 por canal Frecuencias Filtradas: 31.5 Hz, 40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz Impedancia de Entrada: 20k ohms Impedancia de Salida: 1.5k ohms Máximo Nivel de Salida: 11 VAC Control de Nivel: +/- 12 dB Relación Señal-Ruido: 90 dB Distorsión: 0.
日本語 PV®215EQ グラフィックイコライザ 概要 Peavey Electronics PV 215EQ グラフィックイコライザをお買い上げいただきありがとうございます。PV 215EQ は、Peavey の特徴で ある低ノイズ、低歪み設計を採用したデュアルチャンネル EQ です。頑丈に作られた PV 2I5EQ は、ゲイン±I2 dB、センターデテントの フェーダコントロールと、レベルを示すLED ディスプレイを備えています。このほか、平衡入出力とバイパススイッチを備えています。ステージ でもスタジオでも、自宅のハイファイシステムに手を加えるときでも、PV 2I5EQ は最適な EQ です。 特徴 ➡ デュアルチャンネル (各チャンネル15 バンド) ➡ 2/3 オクターブフィルタセット ➡ イコライゼーション有効範囲25 Hz ~ 16 kHz ➡ 定 Q フィルタ ➡ 各バンド12 dB カットまたはブースト ➡ レベル LED (-12 ~ +17 dB) ➡ ステータスLED付ローカットフィルタスイッチ ➡ XLR 入出力平衡動作 ➡ ステータス LED付バイパススイッチ ➡ グランドリフト
フロントパネル 3 3 6 5 4 2 1 LEVEL LED メーター (1) この LED アレイは -12 dB ~ +17 dBのレベルを示します。 LEVEL コントロール (2) このコントロールは、イコライザセクション全体のレベルを調整します。 信号チェーンのユニティゲインは、この点での喪失信号ゲインを回復することで維持されます。イコライゼーションにより信号 ロスが目立つ可能性はあります。このロスを補うため、BYPASS (5) スイッチを加え、信号レベルをイコライズ後のレベルと 比較します。イコライズ後のレベルがバイパスレベルに近づくまで GAIN コントロールを上げます。耳をガイドにして調整して ください。 EQUALIZER セクション (3) それぞれの周波数でカットまたはブーストの量を調整する校正済みデテントコントロールです。-12 dB (カット) ~ +12 dB (ブースト) の範囲で調整できます。 LOW-CUT フィルタ (4) 40 Hz 未満の周波数を除外するローカットフィルタを有効にするスイッチです。周波数ロールオフは、スイッチがオンのときオ クターブ当
リアパネル 10 9 10 9 8 7 IEC 電源コネクタ (7) 標準IEC 電源コネクタです。付属品として、動作電圧に対応するAC プラグと定格の AC 電源コードが含まれてい ます。 どのような機器でも、グランドピン(接地ピン)は決して取り外さないでください。グランドピンは安全のために取り付けて あります。使用するコンセントにグランドピンがない場合は、適切な接地アダプタを使用し、3番目のワイヤを正しく接 地してください。感電や火災の危険をなくすため、イコライザおよび関連するすべての機器が正しく接地されているか 常に確認してください。 このIEC 電源コネクタには電源ヒューズホールダが組み込まれています。本体の電源を入れることができない場合 には、ホールダから引き出してヒューズを取り外します。ヒューズが使用できる状態か確認します。使用できない場合 は、対応する値、定格のヒューズと交換します。ヒューズが繰り返し切れる場合は、最寄りの指定Peaveyサービスセ ンターにお問い合わせください。 GROUND LIFT スイッチ (8) 「主電源セーフティグランド」はそのままの状態で、回路グラン
PV ®215EQ グラフィックイコライザ 仕様 チャンネル: 2 コネクタ: XLR 平衡入出力 バンド: チャンネル当たり15 周波数センター: 31.5 Hz, 40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz 入力インピーダンス: 20k オーム 出力インピーダンス: 1.5k オーム 最大出力レベル: 11 VAC レベルコントロール: +/- 12 dB 信号ノイズ比: 90 dB 歪み: 0.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: 09/15/2010 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
U.S. CUSTOMER WARRANTY REGISTRATION Optional Product Extended Warranty Registration Give us some information and put your extended warranty into effect! Please take a few minutes to fill out this information/survey sheet to help us get to know and serve you better. To save time, submit your warranty registration online at www.peavey.com/support/warrantyregistration 1. 7.
FROM: Place Postage Here Peavey Electronics Corporation Attn: Warranty Department P.O.