Installation User Manual

ManualsBrandsPeerless-AV ManualsMonitorsFPZ-670

Max Load Capacity 400 lb (181.4 kg)

200 lb (90.7 kg) Max Load Capacity per screen

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 05-08-08 SHEET #: 202-9280-1

Installation and Assembly:

Flat Panel Stand for 50" - 71" Plasma Screens

Model: FPZ-670

Features:

• Fits single or back-to-back 50" - 71" flat panel screen

• Up to Vesa screens with additional PLP screen

• Supports non-Vesa screens with adapter plate (sold separately)

• Internal cable management to easily route cords from the screen to the base of the stand

• Base cover is designed to conceal content drivers and surge protectors

• Vertical adjustment on 6" columns for ideal screen viewing height

• Hook-on design allows screen to rest in place while screen is being secured

• Portrait or landscape orientation

Summary of content (7 pages)

PAGE 1
Installation and Assembly: Flat Panel Stand for 50" - 71" Plasma Screens Model: FPZ-670 Features: • • • • • • • • Fits single or back-to-back 50" - 71" flat panel screen Up to Vesa screens with additional PLP screen Supports non-Vesa screens with adapter plate (sold separately) Internal cable management to easily route cords from the screen to the base of the stand Base cover is designed to conceal content drivers and surge protectors Vertical adjustment on 6" columns for ideal screen viewing height Hook-
PAGE 2
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307.
PAGE 3
Parts List A B C D E F G H I J K L M N O P Q R S T Description main tube base carriage adapter plate base cover cable access cover M5 x 8 mm socket pin screw M4 x 10 mm phillips screw M4 x 20 mm M6 x 12 mm pan head M6 x 20 mm phillips screw M6 x 30 mm phillips screw 128 x 313 x 437H retaining spacer M10 x 15 mm socket screw M6 x 20 mm serrated washer head socket pin screw bumper strip 5/16-24 x 1/4 set screw 6 mm allen wrench 4 mm allen wrench M5 x 10 mm socket pin serrated washer head Qty.
PAGE 4
1 For some situations, bumper strip (P) may be required to keep base (B) level. If so, cut bumper strip (P) into five equal pieces and adhere one piece to each corner and one piece to center of bottom side of base (B). 2 Slide two main tubes (A) onto base (B) and secure using four set screws (Q) as shown in figure 2 and detail 1. Tighten screws using 4 mm allen wrench (S). Note: The pieces can also be used in other locations on the base's bottom for other situations.
PAGE 5
Slide carriage (C) onto main tubes (A). Slide carriage to desired height and secure using four set screws (Q) as shown in detail 1. Tighten screws using 4 mm allen wrench (T). Note: Orientation of "UP" arrow is critical.
PAGE 6
Attaching Adapter Plate to Screen with VESA 200 x 200 Mounting Pattern WARNING • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. 6 Choose hole pattern as shown in figure 6.1. Attach adapter plate (D) to back of screen using four M6 x 12 mm screws (J) as shown. Note: Orientation of "UP" arrow is critical.
PAGE 7
6 Portrait orientation Choose hole pattern as shown in figure 6.3. Attach adapter plate (D) to back of screen using four M10 x 15 mm screws (N) as shown. Tighten screws using 6 mm allen wrench (R). Note: Orientation of "UP" arrow is critical. D N fig 6.3 7 Hook adapter plate (D) onto carriage (C) and secure using two M6 x 20 mm serrated washer head socket pin screws (O) as shown in figure 5 and detail 3. Tighten screws using 4 mm allen wrench (S).