Installation User guide

ManualsBrandsPeerless-AV ManualsMonitorsHP432

Max Load Capacity: 150 lb (68 kg)

Installation and Assembly

Models: HP432, HP432-S

ISSUED: 08-1-12 SHEET #: 090-9125-10

2300 White Oak Circle. • Aurora, IL 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Desk top stand for VESA 200mm x 200mm and 200mm x 100mm

Summary of content (7 pages)

PAGE 1
Installation and Assembly Models: HP432, HP432-S Desk top stand for VESA 200mm x 200mm and 200mm x 100mm Max Load Capacity: 150 lb (68 kg) 2300 White Oak Circle. • Aurora, IL 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.
PAGE 2
0 5 5 Note: Read instruction sheet before you start installation and assembly. Before you begin, make sure all parts shown are included with your product. Parts List A B C D F G H I J K Description Qty. support tube base backer plate desktop swivel base adapter plate thrust washer split washer 1/4-20 x 1/2" phillips screw M4 x 12 mm serrated socket pin screw 4 mm allen wrench 10-32 x 1/2" set screw L 1/4-20 x.1.
PAGE 3
1 Use base backer plate (B) as a template to mark location of holes. Drill four holes using a 17/64'' drill bit in a square formation. In the center of the square formation drill 2" to 3" cord management hole. B square FORMATION Cord management cut-out FRONT OF SCREEN BOTTOM VIEW WARNING • Wooden mounting surface requires a minimum of 3/4" thickness to hold screen securely. 2 If the desk thickness is 3/4" use 1/4-20 x 1.5" threaded rods (L).
PAGE 4
Swivel Restriction Refer to fig. 4.1 and 4.2, select the desired swivel degree. Using a 3/32" allen wrench, fasten two set screws (K) where indicated below to the outside of desired angle in steel base (C). 4 NOTE: Set screws (K) must be bottomed out into base. A 210° 240° C 210° Lock at 0° 60° 30° 30° 240° 40° 120° 180° FRONT FRONT fig. 4.1 Mounting to Support Surface fig. 4.
PAGE 5
Mounting using Non-Security 5 Align backer plate (B) with threaded rods (M). NOTE: Washer (F) must be centered. 6 Align base assembly (step 5) with supporting surface and base (C) pattern facing the front as shown in Detail 1. Tighten four fender washers (L) with four lock nuts (N) in the sequenced pattern shown in Figure 6.1 with the 1/4 - 20 locknuts (N) at minimum flush with the bottom of the threaded rods (L or M). FRONT OF SCREEN B L or M F O FRONT OF SCREEN 1 fig. 5.1 3 4 2 fig. 6.
PAGE 6
8 NOTE: Adapter plate support box (D) can be flipped either way to allow necessary screen clearance. For best results, have screen close to desktop but not touching. Adapter plate support box (D) is adjustable up to 6" at 1" increments. Attach adapter plate support box (D) to support tube (A) as shown in fig 7.1. Fasten two 1/4-20 x 1/2" phillips screws (H) and two split washers (G) through adapter plate support box (D) and support tube (A), as shown in fig. 7.2. Optional D D A A D H fig. 8.
PAGE 7
WARNING • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. 9 For installing screens with a VESA 200 x 100 hole pattern: Using the 4mm allen wrench (J), attach screen to adapter plate (D) using four M4 x 12 mm serrated socket pin screws (I) and four #10 SAE washers (Q) as shown in figure 8.1.