Installation

ManualsBrandsPeerless-AV ManualsMonitorsPS-2

1 of 6 ISSUED: 08-28-02 SHEET #: 200-9417-3 12-02-04

Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.

IMPORTANT! Read entire instruction sheet before you start assembly and installation.

Model: PS 2

Place swivel lock bracket (I) on wall arm assembly (J)

as shown to the right.

Place rotation box (A) with threaded holes up over

wall arm assembly (J). Insert tilt pivot retainer

assembly (B) through rotation box (A) and wall arm

assembly (J).

Secure rotation box (A) to swivel lock bracket (I) using

four M5 x .8 x 10mm phillips screws (H). Align holes in

tilt pivot retainer assembly (D) with holes in rotation

box (B) and secure with two 10-32 x 1/2" socket pin

screws (C) as shown.

Before you start make sure all parts

listed are included with your product.

PART # QTY. DESCRIPTION

A 200-1434 1 rotation box

B 200-1285 1 tilt pivot retainer assembly

C 520-1055 2 10-32 x 1/2" socket pin screw

D 200-0288 1 pitch roll assembly

E 520-1001 1 carriage bolt 3/8"-16 x 3"

F 520-9263 12 M10 x 1.5 x 15mm penta-pin screw

G 590-1087 1 tilt adjustment knob

H 520-9250 4 M5 x .8 x 10mm phillips screw

I 200-1311 1 swivel lock bracket

J 200-0342 1 wall arm assembly

K 520-9260 1 M10 x 2" penta-pin™ driver

L 200-1343 1 wall plate

M 590-0097 4 concrete anchor

N 540-1008 4 fender washer

O 5SI-015-C03 4 wood screw

P 560-9646 1 4mm security allen wrench

Parts List

Note: Some parts may appear slightly different than illustrated.

THREADED

HOLES

Note: Lay flat on sufrace for ease of assembly.

Hole in bottom of

rectangular tube

denotes bottom of

wall arm assembly.

Installation & Assembly - Solid•Point

™

Wall Mount with Tilt

and Swivel for 60 / 61" Screens

Summary of content (6 pages)

PAGE 1
Installation & Assembly - Solid•Point™ Wall Mount with Tilt Model: PS 2 and Swivel for 60 / 61" Screens IMPORTANT! Read entire instruction sheet before you start assembly and installation. Before you start make sure all parts listed are included with your product. Parts List PART # QTY.
PAGE 2
NOTE: Refer to adapter plate instruction sheet (not included with PS-1) for attachment of adapter plate to plasma before proceeding with step 2. GENERIC ADAPTER BRACKET Insert and tape carraige bolt (E) into top hole of pitch roll assembly (D). Attach pitch roll assembly (D) to adapter bracket with four M10 penta-pin screws (F). Tighten M10 screws with penta-pin driver (K). E D Note: Adapter bracket may be ordered separately and will vary in size and style.
PAGE 3
Use stud finder to locate stud centers. Place wall plate (L) on wall as template, level wall plate and mark center of studs with pencil. The wall plate can be mounted on 16" centers. When mounted to 16" studs, the wall plate can be shifted 4" left or right of center if desired. L Note: Hardware provided is for attachment of plasma mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.
PAGE 4
For Concrete Walls drill four 1/4" (6mm) dia. holes to a minimum depth of 2.5" (64mm) on marks made in step 1. Insert anchor (M) in holes flush with wall as shown (right). Place wall plate (L) over anchor and secure with four #14 x 2.5" (6mm x 65mm) wood screws and washers (O & N) as shown at bottom of page. Make sure wall plate is level before placing fasteners. Tighten all fasteners.
PAGE 5
WARNING • Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 penta-pin screws (F) into rotation box (A) as shown. Leave approx. 1/4” of exposed thread. A .25" F Hook pitch roll assembly (D) onto M10 penta-pin screws (F). Insert carriage bolt (E) into slot of tilt pivot retainer assembly (B) as shown. Install tilt adjustment knob (G). Install remaining two M10 penta-pin screws (F).
PAGE 6
NOTE: Refer to page four of accompanying instruction sheet for attachment of PS 1 with plasma to wall plate before proceeding with step 4. Depending on the specific size & weight of the plasma, plasma may appear to lean sideways. Pitch roll assembly (D) allows plasma to be manually adjusted, so plasma can be horizontal. To adjust, gently rotate plasma by hand to desired position. PLASMA IMPORTANT! Center bolt is factory torqued for optimal performance to adjust for range of plasma sizes.