Installation and Assembly: 32" - 65" Flat Panel Display Cart Models: SC560DPB, SC560DPS Max UL Load Capacity: 115 lb (52 kg) display 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
Before you begin, make sure all parts shown are included with your product. Parts List A B C D E F G H I J K L M N O P Description column bracket adapter plate column base column right leg left leg 3/8-16 x 1-1/2" bolt joint connector caster caster with brake 5/16"-18 x 3/8" socket cap screws 1/4-20 x 12mm socket screws 5/16 x 1/4" set screw 4mm allen wrench 7/32" allen wrench 3/16 allen wrench Qty.
Adapter Bracket Fasteners M5 x 12 mm (4) (520-1027) M6 x 12 mm (4) (520-1128) M5 x 25 mm (4) (520-9543) M8 x 12 mm (4) (520-9571) M6 x 25 mm (4) (520-1208) 4 of 11 .
1 Insert right leg (E) into column base (C) as shown in figure 1.1. Then line up holes of right leg with holes in column base. Fasten right leg to column base using two 3/8-16 x 1-1/2" bolts (G) and two joint connectors (H), tighten using 3/16" allen wrench (P) and 7/32" allen wrench (O) as shown in figure 1.2. NOTE: Left and right legs can be identified by looking at the cart from the front. Repeat for left side of column base with left leg (F). fig. 1.1 fig. 1.
3 Insert columns (D) over column base supports (C) and align cable management holes. Secure columns to column base supports using four 5/16" socket screws (K). Tighten screws using 3/16" allen wrench (P). Insert two 1/4-20 x 12mm socket screws (L) into column bracket (A) using 4mm allen wrench (N), leaving 3/16" of exposed thread as shown in detail 1. 4 A L D CABLE MANAGEMENT HOLES C K 3/16" DETAIL 1 5 Insert column bracket (A) over columns (D) and adjust to desired height.
Installing Adapter Plate WARNING • Tighten screws so adapter plate is firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the display inserts or if screws bottom out and adapter plate is still not tightly secured, damage may occur to display or product may fail.
Attaching Display using VESA 100, 200 or VESA 300 Mounting Pattern WARNING • If screws don't get three complete turns in the display inserts or if screws bottom out and adapter plate is still not tightly secured, damage may occur to display or product may fail. For Flat Back Display 7-1 Select the screws from the baffled fastener pack that best fit your display. Begin with the shortest length screw, hand thread through multi-washer and adapter plate (B) into display as shown below.
Mounting Flat Panel Display 8 Attach adapter plate (B) onto 1/4-20 screws of column bracket (A). B A 9 Insert two 1/4-20 x 12mm screws (L) into top holes indicated below for desired display orientation. Adjust display then secure with two 1/4-20 x 12mm screws (L). Tighten all screws using 4mm allen wrench (N).
Cable Management 10 Run cables through columns (D) using cable management holes. CABLE MANAGEMENT HOLES D 10 of 11 ISSUED: 08-31-11 SHEET #: 009-9053-7 07-25-12 © 2012, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners. Peerless Industries, Inc. 2300 White Oak Circle Aurora, Il 60502 www.peerless-av.
LIMITED FIVE-YEAR WARRANTY Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.