Installation and Assembly: 32" - 65" Flat Panel Display Stand Models: SS550P, SS550P-S This product is UL Listed. It must be installed by a qualified professional installer. Max Load Capacity: 150 lb (68 kg) display 50 lb (22.7 kg) per shelf 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. • This product should only be installed by someone of good mechanical aptitude, and fully understands these instructions.
A Before you begin, make sure all parts shown are included with your product. B Parts List A B C D E F G H I J K L M N P Q R S T U Description screen mount bracket hook plate shelf support shelf clamp bracket base universal plate adapter bracket upright glass shelf top cover button bumper 1/4-20 x 12mm decorative screw 1/4-20 x 20mm decorative screw 1/4-20mm nut 3/8-16 x 2.5" socket screw 7/32" allen wrench 4mm allen wrench adhesive felt M10 x15mm socket screw 6mm allen wrench Qty.
Adapter Bracket Fasteners M5 x 12 mm (4) (520-1027) M6 x 12 mm (4) (520-1128) M5 x 25 mm (4) (520-9543) 1 M8 x 12 mm (4) (520-9571) M6 x 25 mm (4) (520-1208) .75" spacer (4) (540-1059) M8 x 25 mm (4) (520-1031) Multi-washer (4) (580-1398) Cut adhesive felt (S) into four pieces as shown in figure 1.1 below and affix to bottom of base (E). 1-1 Attach upright (H) to base (E) using three 3/8-16 x 2.5" socket screws (P). Tighten screws using 7/32" allen wrench (Q).
Loosely attach four 1/4-20 x 12 mm screws (L) and 1/4-20 nuts (N) to shelf support (C). 2 3 3-1 Slide shelf support (C) onto upright (H) so that 1/4-20 nuts (N) slide into slots of upright (H) as shown in figure 3 and detail 1. Slide shelf support to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4 mm allen wrench (R). NOTE: Max of two shelves can be used Max height of top shelf is 34" from base. Max height of second shelf is 28" from base.
Loosely attach six 1/4-20 x 12 mm screws (L) and 1/4-20 nuts (N) to display mount bracket (A). 6 Slide display mount bracket (A) onto upright (H) so that 1/4-20 nuts (N) slide into slots of upright (H) as shown in figure 7 and detail 2. Slide display mount bracket to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4 mm allen wrench (R). 7 A N N SLOT H DETAIL 2 L L H A fig. 7 8 Snap top cover (J) onto upright (H).
Attaching Display Using Universal Plate with Adapter Brackets For attaching displays with VESA 100 hole pattern, skip to page 11. 10 Attach universal plate (F) to hook plate (B) using four M10 x 15 mm socket screws (T). Tighten screws using 6 mm allen wrench (U). 11 Attach hook plate (B) to display mount bracket (A). B F B A T 12 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired display orientation. Tighten all screws using 4 mm allen wrench (R).
Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to display or product may fail.
For Flat Back Display 13-1 Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
Mounting and Removing Flat Panel Display WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the display. 14 Hook adapter brackets (G) onto universal plate (F), then slowly swing display in as shown. Turn screws clockwise at least six times to prevent display from being removed as shown in detail 4. NOTE: Tighten using 4 mm allen wrench (R). Display can be adjusted horizontally if desired.
Attaching Display with VESA 100 Mounting Pattern WARNING • If screws don't get three complete turns in the display inserts or if screws bottom out and hook plate is still not tightly secured, damage may occur to display or product may fail. 10 Choose hole pattern as shown in figure 10. Attach hook plate (B) to back of display using four M4 x 12 mm screws. Tighten screws using a phillips screwdriver. 11 Attach hook plate (B) to display mount bracket (A).