Installation Guide

ManualsBrandsPella ManualsExterior DoorsRolscreen 32-in x 81-in Cranberry Full-View Aluminum Storm Door

Closer & Installation Kits

Loose Parts

Pella

Storm Door Owner's Guide and Installation Manual

Select

Series Rolscreen

Models

202220861

NOTE TO THE INSTALLER:

This Owner’s Guide and Installation Manual is the property of the homeowner.

Please leave it with the homeowner upon completion of the installation.

Recommended Tools

Power Drill with

1/8", 3/8" drill bits

(7/8" spade bit included)

Tape Measure

Phillips Screwdriver #2

For safety reasons, the assistance of a second person is recommended when handling the door.

Read the legend below in order to easily follow along and install your storm door.

For reference, the storm door assembly is illustrated on page 2.

Legend

Follow the steps in order

Steps in BLUE apply to LEFT HINGE congurations.

(Hinge side will be determined in a later step.)

Steps in GREEN apply to RIGHT HINGE congurations.

(Hinge side will be determined in a later step.)

To order replacement parts, call

1-800-374-4758

or visit us at

www.pella.com

Please have your registration number

ready when you contact us either by

telephone or on the internet.

TROUBLESHOOTING GUIDE is located on page 12 of this manual.

Lay door ﬂat. Make sure ALL parts are accounted for

before discarding carton.

The carton material is recyclable

Summary of content (12 pages)

PAGE 1
Pella® Storm Door Owner's Guide and Installation Manual Select® Series Rolscreen® Models NOTE TO THE INSTALLER: This Owner’s Guide and Installation Manual is the property of the homeowner. Please leave it with the homeowner upon completion of the installation. 1 2 Recommended Tools Power Drill with 1/8", 3/8" drill bits (7/8" spade bit included) Tape Measure Phillips Screwdriver #2 For safety reasons, the assistance of a second person is recommended when handling the door.
PAGE 2
Storm Door Components NOTE: Actual door styles may vary from illustrations, however, the installation steps will be the same. Door Top Mounting Frame/ Drip Cap Installation Kit Includes mortise lock body, edge cover, deadbolt screw and 7/8” spade bit Hinge Mounting Frame Latch Mounting Frame Registration Number Extenders Closer Kit Includes mounting screws, expander screws and some handle components Retractable Screen Handle Kit This is your door’s identification number.
PAGE 3
START 1 Your Installation Determine the side you want your door to hinge. On the HINGE SIDE, remove hardware drilling template sticker (keep the template on the latch side). Position edge cover over mortise hole on hinge side of door.
PAGE 4
3 Attach Hinge Rail to Storm Door Right Hinge Installation 3A Place interior side face up. 3B Locate hinge locator mark near top e nd of door, and place hinge rail as shown. Note: The longest point of the hinge rail will extend past the top of the door by 3⁄16". Attach hinge rail with #10 x 1/2" hinge screw from Bag B. IN T E R DOOR IO R O F #10x1/2 in. unpainted 3b TO P E ND O F DOO R 3C Install remaining hinge screws from Bag B starting from the bottom.
PAGE 5
4 Attach Storm Door to Door Frame (Right Hinge shown) 4A Slide rail extender into the 4B Hang storm door onto door bottom of the hinge rail. frame using the placeholder screw. The door will settle approximately 1/16". Tighten screw while pushing top of hinge rail tight against the door frame. 4C At the second hinge from 4D Slide rail extender to sill. the bottom, install a door Loosen hinge rail screw as installation screw from Bag needed. B in one of the pre-punched holes. Do not over tighten.
PAGE 6
Install Latch Rail (Right Hinge shown) 6A Slide rail extender into the bottom of latch rail. 6B Place latch rail tight against the drip cap. 6C Slide rail extender to sill. 6E Starting at the top hole, attach the latch rail with a #8 x 1” screw from Bag C. Align the edge of the door panel and mounting frame from top to bottom. Continuing down the latch rail, install one screw at a time, keeping a consistent reveal. 6F Cut extender weather stripping to length, p eel adhesive backing and install.
PAGE 7
8 Install Expander 8A Slide expander on door with slots to the interior. 8B Adjust the expander until the sweep touches the threshold. 8C Secure expander with the #8 x 1/2" screws from Bag D, located in the closer kit. #8x1/2 in. Painted 9 Finishing Touches Screw Covers Snap strips into place by anchoring the outer side first (Screw covers may need to be trimmed to length). Start at the top ends and slide finger down strip while pressing.
PAGE 8
9 Finishing Touches continued Window Handle Installation 9A Install spring into bottom of handle. Spring SpringSpring HandleHandle Handle SpringSpring Spring Handle Handle Handle Bottom Side Side Bottom Bottom Side Bottom Side Side Bottom Side Bottom Top TopSide Side Top Side TopSide Side Top Top Side 9B To install handle onto window, open top window to a comfortable height for handle installation.
PAGE 9
10 Door Closers 10A On the hinge side of your entryway, position a jamb closer bracket even with the top of the expander (see the dotted line in the illustration) and 1/4" back from the mounting frame. 10B Install the bottom jamb closer bracket using four jamb bracket screws (#10 x 1-1/2" Phillips pan head) from Bag E.
PAGE 10
Door Closers continued 10H Attach the top closer rod to the jamb bracket using the short closer pin from Bag E, then pull the door closer and slide the LONG spacer clip onto the closer rod. 10I Attach the door closer bracket to the door closer by removing the O-ring from the long closer pin, inserting the pin, and securing with the O-ring. 10J Rest the door closer bracket on the screen head cover for vertical placement.
PAGE 11
Care and Maintenance Door Cleaning Use a soft cloth with any household grease-cutting cleaner to clean the door. PLEASE NOTE: Thin marks on the painted surfaces of the door can be removed using turpentine and lightly rubbing with a clean cloth. IMPORTANT: DO NOT use brass polish or steel wool on the bottom expander. Use a household grease-cutting cleaner or a mild soap and water solution.
PAGE 12
Troubleshooting Guide If you have a question that you do not see listed here, or have not been able to resolve through your Pella® Owner’s Guide and Installation Manual, call one of our customer service representatives toll-free at 1-800-374-4758 or visit www.pellastormdoors.com. Common Questions Probable Causes Suggested Solutions Door does not open or close properly Entryway framing is out or square/plumb or frame is warped 1. Verify the entryway framing and shim as necessary.