User Manual

ManualsBrandsPella ManualsFurnitureClad Hinged patio Door With Adjustable HInges 80JJ0103

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION

FOR CLAD HINGED PATIO DOOR WITH ADJUSTABLE HINGES

PARA LA PUERTA PARA PATIO REVESTIDA, CON BISAGRAS ADJUSTABLES

These instructions were developed and tested for use with typical wood frame wall construction in

a wall system designed to manage water. These instructions are not to be used with any other

construction method. Installation instructions for use with other construction methods, multiple

units or bow and bay windows, may be obtained from Pella Corporation or a local Pella retailer,

or by visiting http://www.pella.com. Building designs, construction methods, building materials,

and site conditions unique to your project may require an installation method different from

these instructions and additional care. Determining the appropriate installation method is the

responsibility of you, your architect, or construction professional.

Part Number: 80JJ0103

'SBNJOH

4JMM'MBTIJOH5BQF

4JMM'MBTIJOH5BQF

/BJMJOH'JO

8BUFS

3FTJTUJWF

#BSSJFS

4IFBUIJOH

5PQ

'MBTIJOH

5BQF

'JO

$PSOFS

%PPS5PQ

%PPS#PUUPN

4JEF

'MBTIJOH

5BQF

4JEF

'MBTIJOH

5BQF

$PSOFS

'MBTIJOH

5BQF

$PSOFS

'MBTIJOH

5BQF

0QUJPOBM

/BJMJOH'JO

4JMM4VQQPSU

Always read the Pella

Limited Warranty before purchasing or installing Pella products. By

installing this product, you are acknowledging that this Limited Warranty is part of the terms of the

sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella

product warranty. See Limited Warranty for complete details at http://warranty.pella.com.

Summary of content (8 pages)

PAGE 1
Part Number: 80JJ0103 ©2008 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR CLAD HINGED PATIO DOOR WITH ADJUSTABLE HINGES PARA LA PUERTA PARA PATIO REVESTIDA, CON BISAGRAS ADJUSTABLES $PSOFS 'MBTIJOH 5BQF 4JEF 'MBTIJOH 5BQF 'JO $PSOFS %PPS 5PQ /BJMJOH 'JO 5PQ 'MBTIJOH 5BQF $PSOFS 'MBTIJOH 5BQF 8BUFS 3FTJTUJWF #BSSJFS 4IFBUIJOH 'SBNJOH 0QUJPOBM /BJMJOH 'JO 4JEF 'MBTIJOH 5BQF %PPS #PUUPN 4JMM 4VQQPSU 4JMM 'MBTIJOH 5BQF 4JMM 'MBTIJOH 5BQF Always read the Pella
PAGE 2
YOU WILL NEED TO SUPPLY: TOOLS REQUIRED: s #EDAR OR )MPERVIOUS SHIMS SPACERS TO s GALVANIZED ROOlNG NAILS LB s D NAIL s #LOSED CELL FOAM BACKER ROD SEALANT BACKER TO FT s 0ELLA® SmartFlash™ foil backed butyl window and door ﬂashing tape or equivalent s (IGH QUALITY EXTERIOR GRADE POLYURETHANE OR SILICONE SEALANT TO TUBES PER DOOR s 'REAT 3TUFF ™ Window and Door Insulating Foam Sealant by the Dow Chemical Company or equivalent low pressure polyurethane window and door foam
PAGE 3
E. Apply sill ﬂashing tape #1. Cut a piece of ﬂashing tape 12" longer than the opening width. Apply at the bottom of the OPENING AS SHOWN % SO IT OVERHANGS TO THE EXTERIOR Note: The tape is cut 12" longer than the width so that it will extend 6" up each side of the opening. F. Tab the sill ﬂashing tape and fold. Cut 1" wide tabs at each CORNER FROM EACH SIDE OF CORNER & &OLD TAPE TO THE EXTERIOR AND PRESS lRMLY TO ADHERE IT TO THE WATER RESISTIVE BARRIER ' Apply sill ﬂashing tape #2.
PAGE 4
E. Plumb and square door. Place shims at each hinge and lock strike location between the door and the sides of the opening. )NSERT SHIMS IN OTHER LOCATIONS AS NEEDED STARTING UP FROM THE bottom of the door to square it in the opening. Make sure that the REVEAL AROUND THE DOOR S IS EQUAL /N DOUBLE DOORS MAKE SURE THAT panels are even across the bottom. Ó &YUFSJP S Note: On center latch double doors the lock strike will not be shimmed since it is located in the center of the unit. DO NOT over shim. F.
PAGE 5
L. Check door operation. Open and close the door to check for proper operation. Make sure the door will latch correctly. Note: If there are any problems with the operation, recheck and adjust the reveal. M. Adjust the reveal if needed.
PAGE 6
B. Apply top ﬂashing tape. Cut a piece of ﬂashing tape long ENOUGH TO GO ACROSS THE TOP OF THE DOOR AND EXTEND AT least 1" past the side ﬂashing tape on both sides. Apply the tape 1/2" onto the frame cladding, over the top NAILING lN AS SHOWN &OLD THE OVERLAPPING TAPE DOWN AND PRESS ALL TAPE DOWN lRMLY Note: The top ﬂashing tape must overlap the side ﬂashing tape to prevent water from getting behind it. Î C. Fold down top ﬂap OF WATER RESISTIVE BARRIER # &YUFSJP S D.
PAGE 7
5 SEALING THE DOOR TO THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other exterior ﬁnish material, leave adequate space between the door frame and the material for sealant. Refer to the illustration that corresponds to your ﬁnish material. Note: The sealant details shown are standard recommendations from the sealant industry. Contact your sealant supplier for recommendations and instructions for these and any other applications.
PAGE 8
INTERIOR FINISHING )F PRODUCTS CANNOT BE lNISHED IMMEDIATELY COVER WITH CLEAR PLASTIC TO PROTECT FROM DIRT DAMAGE AND MOISTURE 2EMOVE ANY CONSTRUCTION RESIDUE BEFORE lNISHING 3AND ALL WOOD SURFACES LIGHTLY WITH GRIT OR lNER SANDPAPER $/ ./4 USE STEEL WOOL "% #!2%&5, ./4 4/ 3#2!4#( 4(% ',!33 Remove sanding dust. 0ELLA PRODUCTS MUST BE lNISHED PER THE BELOW INSTRUCTIONS FAILURE TO FOLLOW THESE INSTRUCTIONS VOIDS THE Limited Warranty.