1 MiniMax NT ® Series Pool & Spa Heaters OPERATION & INSTALLATION MANUAL To Consumer Retain For Future Reference U.S. Patent Numbers 6,295,980 5,318,007 - 5,228,618 5,201,307 - 4,595,825 WARNING FOR YOUR SAFETY - READ BEFORE OPERATING • If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury or loss of life. • Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or death.
Customer Service If you have questions about ordering Pentair Pool Products replacement parts, and pool products, please use the following contact information. Customer Service (8 A.M. to 5 P.M. Pacific Time) Phone: (800) 831-7133 (press 3 in voice mail) Fax: (800) 284-4151 Technical Support for Pentair Pool Products Sanford, North Carolina (8 A.M. to 5 P.M. Eastern Time) Phone: (919) 566-8000 Fax: (919) 566-8920 Moorpark, California (8 A.M. to 5 P.M. Pacific Time) Phone: (805) 523-2400 (Ext.
Table of Contents Section I. Heater Identification Information ........................................................... 4 Section II. Introduction ............................................................................................ 5 Important Notices ...................................................................................................................................................................... 5 Warranty Information ..................................................
Section I. Heater Identification Information 4 Heater Identification Information To identify the heater, see rating plate on the inner front panel of the heater. There are two designators for each heater, one is the Model Number and the other is the Heater Identification Number (HIN). a.
Section II. Introduction 5 Introduction MiniMax® NT Series Pool and Spa Heaters Congratulations on your purchase of a MiniMax NT high performance heating system. Proper installation and service of your new heating system and correct chemical maintenance of the water will ensure years of enjoyment. The MiniMax NT is a compact, lightweight, efficient, induced-draft, gas fired high performance pool and spa heater that can be directly connected to schedule 40 PVC pipe.
Section II. Introduction 6 CODE REQUIREMENTS The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and/or CSA B149.1, Natural Gas and Propane Installation Codes. The heater, when installed, must be electrically grounded and bonded in accordance with local codes or, in the absence of local codes, in the USA, with the National Electrical Code, ANSI/NFPA 7; in Canada, with Canadian Electric Code, CSA C22.1.
Section III. Installation 7 Installation Instructions SPECIFICATIONS These installation instructions are designed for use by qualified personnel only, trained especially for installation of this type of heating equipment and related components. Some states require installation and repair by licensed personnel. If this applies in your state, be sure your contractor bears the appropriate license. See Figure 1 for Outdoor and Indoor Installations. DIMENSIONS IN INCHES 24.05 Heater Depth 3.
Section III. Installation 8 MANUAL BY-PASS POOL HEATER TO POOL CHECK VALVE PUMP FILTER MANUAL BY-PASS GATE VALVE Model CHECK VALVE Figure 2. Where the flow rate exceeds the maximum 120 GPM, a manual bypass should be installed and adjusted. After adjustments are made, the valve handle should be removed to avoid tampering. See Figure 2. FROM POOL PLUMBING CONNECTIONS The MiniMax NT heater has the unique capability of direct schedule 40 PVC plumbing connections.
Section III. Installation 9 WATER CONNECTIONS Reversing Headers — Reversible Inlet/Outlet Connection The MiniMax NT Series heater is factory assembled with right side inlet/outlet water connections. The inlet/outlet header can be reversed for left side water connections without removing the heat exchanger. Reversing Water Connections Tools required: Phillips Screw Driver 9/16 in. Socket and Wrench 1/2 in. & 9/16 in. Open Wrench 1. Remove the right and left large access doors.
Section III. Installation 10 Reversible Inlet/Outlet Connection, cont’d. On the MiniMax NT Series heater there is insulation installed by the factory on the return head side of the heaters. This insulation is there so that if the heads are reversed in the field, during initial installation of the heater, the high limits will be insulated from the heat radiating from the flue collector. 6. Return head in position before removal. This view shows the insulation installed by the factory.
Section III. Installation 11 GAS CONNECTIONS GAS LINE INSTALLATIONS Before installing the gas line, be sure to check which gas the heater has been designed to burn. This is important because different types of gas require different gas pipe sizes. The rating plate on the heater will indicate which gas the heater is designed to burn. The tables, shown on page 12, show which size pipe is required for the distance from the gas meter to the heater. The table is for natural gas at a specific gravity of .
Section III. Installation 12 GAS PIPE SIZING Table 2. PIPE SIZING FOR GAS LINE CONNECTIONS MAXIMUM EQUIVALENT PIPE LENGTH (Ft.) Natural Gas at 1000 B.T.U. per Cubic Foot Propane Gas at 2500 B.T.U.
Section III. Installation 13 TESTING GAS PRESSURE Inlet Manifold 1. Push the power switch to “OFF”. 2. Turn the gas valve knob to “OFF”. 3. Remove 1/8 in. NPT plug on the outlet side of the valve and screw in the Manifold Inlet fitting from the Manometer kit. 4. Connect the Manometer hose to the fitting. 5. Turn the gas valve knob to “ON”. 6. Turn on the heater and read the Manometer. 7.
Section III. Installation 14 INDOOR VENTING — General Requirements The vent pipe must be the same size or larger. The MiniMax NT heaters are capable of a 360-degree discharge rotation and operate with a positive vent static pressure and with a vent gas temperature less than 400° F. The total length of the horizontal run must not exceed the length that is listed below in the tables. NOTE The allowable vent runs for each vent pipe diameter are different and can not be exceeded.
Section III. Installation 15 INDOOR INSTALLATION (USA ONLY) OUTDOOR SHELTER INSTALLATION (CANADA) Chimney or Gas Vent Vent Cap and Riser Furnished by Installer See page 16 for Vent Adaptors All products of combustion and vent gases must be completely removed to the outside atmosphere through a vent pipe which is connected to the stack adaptor.
Section III. Installation 16 COMBUSTION AIR SUPPLY Air Supply Requirements Guide for MiniMax NT Heaters For indoor installation, the heater location must provide sufficient air supply for proper combustion and ventilation of the surrounding area.
Rev. E 4-15-05 Roof Jack Roof Thimble 3 ft. min. Vent Cap Chimney/Gas Vent 2 ft. min. may use a single wall vent pipe with permanently sealed seams, joints and proper insulating materials. must be suitable for use with category III appliances with flue gas temperature ratings less than 400 deg. F. must be the same diameter as the vent connector. Vent pipe extension: must terminate with an approved (listed) roof jack, storm collar, and vent/weather cap.
Section III. Installation 18 OUTDOOR INSTALLATION (Outdoor Shelter Installation in Canada, see page 15) For outdoor installation with an exhaust grill, the heater must be placed in a suitable area on a level, noncombustible surface. Do not install the heater under an overhang with clearances less than 3 feet from the top of the heater. The area under an overhang must be open on three sides. Do NOT, under any circumstances, install the heater under ANY deck.
Section III. Installation 19 ELECTRICAL CONNECTIONS Electrical Rating 60 Hz 120 / 240 Volts AC, single phase CAUTION This heater is designed to operate at 120 or 240 VAC. It is not recommended to be connected to OR operate on a 208 VAC. NOTE • The MiniMax NT heater is prewired for 240-volt AC connection using the “RED” connector and the “BEIGE” common connector; see Figure 16 below. For 120-volt AC supply, remove the “BEIGE” common connector and plug it into the “BLUE” common connector.
BK REMOTE CONTROL MANUAL FOR & INSTALLATION PR J5 J8 J6 J1 J2 GY SPA COM POOL R W GY O PR BR J17 BL BK Y BK BK 9 W 8 GY GY VLV GND PS TH 24VAC IGN/120 L1 IGN/240 L2 IGN/FS FLAME SENSOR IGNITER 9 8 7 6 5 4 F1 F2 FC 9 GY J16 W W BK BK W W PR W 2 2 W W P13 1 1 J13 Y BLOWER J14 P14 W 6 6 BK BK BK O 5 5 BK BK W 3 3 W BK 4 4 BK AVEC UNE ECHELLE DE TEMPERATURE A 18 AWG, 600V, 150 DEGRES CELSIUS.
Section IV. Operation 21 Operation Instruction BASIC SYSTEM OPERATION 1. Start pump, make sure the pump is running and is primed, to close the water pressure switch and supply power to heater. Be sure the pool and/or spa is properly filled with water. Follow the Lighting/Operating instructions below.
Section IV. Operation 22 SAFETY CONTROLS Figure 21. VACUUM AIR PRESSURE (FAN) SWITCH The air pressure switch, (see Figure 21), is a safety device used to insure that the combustion air blower (fan) is operating and has been designed to monitor the vacuum (negative) pressure within the blower housing. The air pressures switch is factory set and is connected upstream of the ignition module. The ignition module does not operate unless the air pressure switch and all safety switches are closed.
Section IV. Operation SAFETY CONTROLS, (cont’d.) 23 Flame Current Check Point HIGH LIMITS A “High Limit”, is a safety device that opens the electrical circuit and shuts off the heater based on a water temperature set point within the “High Limit Device”. The MiniMax NT series of heaters contains two (2) high limit devices which are located on the main inlet / outlet header, one sensing the inlet water temperature and one sensing the outlet water temperature.
Section IV. Operation 24 DIGITAL DISPLAY TEMPERATURE CONTROLLER (DDTC) REMOTE BUTTON POWER REMOTE PRESSURE SW POOL SPA SYSTEM INDICATOR LIGHTS THERMOSTAT POOL BUTTON SPA BUTTON OFF HEATING SERVICE TEMPERATURE SETTING POOL OFF BUTTON SPA TEMP. UP PRESS ANY ARROW ONCE TO CHECK SET TEMPERATURE Figure 26. SPA AND POOL TEMPERATURE SET BUTTONS TEMP.
Section IV. Operation 25 Figure 27. Rev.
Section IV. Operation 26 SET UP The MiniMax NT Heater comes from the factory preset with a pool temperature setting of 78° F. and a preset spa temperature of 100° F., and in the off mode setting. Once the power is turned on, the DDTC board will do a self diagnostic internal check, during this time the display will first read “888”, then the display will switch to three dashes “- - -“, this process takes approximately ten (10) seconds.
Section IV. Operation 27 • HEATING The heating light is on any time the thermostat has signaled a call for heat which initializes the ignition safety circuit — the light comes on indicating successful firing of the main burners and stays on until the pool/spa reach the water temperature setting. • SERVICE The service light is off during normal operation of heater. The light only comes on if a problem with a control has occurred or when the heater is first firing.
Section V. Troubleshooting 28 Troubleshooting Instruction TROUBLESHOOTING (DDTC) The DDTC temperature display contains three LED’s with a decimal point between the first and second, this display is also used to display an error code if for some reason there is a failure within the heater control system or a DDTC internal fault. The DDTC will display the actual temperature or set-point temperature or OFF, as selected by the user.
Section V. Troubleshooting 29 TROUBLESHOOTING (GENERAL) Possible Cause Heater will not come on Remedy Check if electrical connections are Automatic ignition system fails correct and securely fastened – If YES, call serviceperson.
Section VI. Maintenance 30 Maintenance Instruction It is recommended that you check the following items at least every six months and at the beginning of every swimming season. 1. Examine the venting system. Make sure there are no obstructions in the flow of combustion and ventilation air. 2. Visually inspect the main burner and the hot surface ignitor. The normal color of the flame is blue. When flame appears yellow, burners should be inspected and cleaned. Check ignitor for damage. 3.
Section VI. Maintenance 31 SPRING AND FALL OPERATION If the pool is being used occasionally, do not turn the heater completely off. Set the thermostat down to 65° F. This will keep the pool and the surrounding ground warm enough to bring the pool up to a comfortable swimming temperature in a shorter period of time. WINTER OPERATION CAUTION • Operating this heater continuously at water temperatures below 68° F. will cause harmful condensation and will damage the heater and void the warranty.
Section VI. Maintenance 32 CHEMICAL BALANCE RULE: 7.4 to 7.6 is a desirable pH range. It is essential to maintain correct pH, see Table 15. POOL AND SPA WATER If pH becomes too high (over alkaline), it has these effects: Your Pentair Pool Products pool heater was designed specifically for your spa or pool and will give you many years of trouble-free service, provided you keep your water chemistry in proper condition.
REPLACEMENT PARTS NT STD w/DDTC — (all Models) NT TSI w/DDTC — (200, 250, and 300 Models) 29 36 30 31 33 34 35 FOR STD ONLY Rev.
\ $ ] ^ ^ ; J ' !" # $ $ % & <= = > ? > @B ! K = > ? !" # $ > & =Q X > & =Q % $ !" # > & =Q > ? > & =Q > ? $ YY > & =Q ; J ' ; ! " > @B ! ! @ \ %] > @B ! ! @ '\ %] X ^ & <= _
\ $ ] ^ ^ ; J ' !" # $ $ % & <= = > ? > @B ! K = > ? !" # $ > & =Q X > & =Q % $ !" # > & =Q > ? > & =Q > ? $ YY > & =Q ; J ' ; J ' ! " > @B ! ! @ \ %] > @B ! ! @ '\ %] X
REPLACEMENT PARTS NT TSI w/DDTC — (400 Model — Starting w/Serial No. 12040039) 1 2 3 4 5 6 7 8 37 9 36 10 35 11 34 12 33 32 13 31 14 30 15 29 28 16 27 18 17 19 20 21 22 23 24 25 26 38 39 40 46 P/N 472235 45 44 43 42 41 Rev.
\ $ ] ^ ^ ] % $ = ; J ' ; J ' ; J ' [ ' !" # & J $ ;' $ ' % & '' <= = > ? > @B ! ' K = > ? !" # JJ $ > & =Q X >
NOTES P/N 472235 Rev.
NOTES Rev.
SAVE THESE INSTRUCTIONS Pentair Water Pool and Spa, Inc. 1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000 10951 W. Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400 P/N 472235 Rev.
1 1 Chauffe-eau pour piscine et spa MiniMax NT ® GUIDE D'INSTALLATION ET DE FONCTIONNEMENT Au consommateur : Veuillez conserver ce guide à titre de référence. Numéros de brevets américains 6,295,980 5,318,007 - 5,228,618 5,201,307 - 4,595,825 MISE EN GARDE POUR VOTRE SÉCURITÉ, VEUILLEZ LIRE CE GUIDE AVANT DE FAIRE FONCTIONNER L'APPAREIL • Si les instructions ne sont pas suivies à la lettre, il peut s'ensuivre un incendie ou une explosion causant des dommages matériels, des blessures ou la mort.
Service Clients Si vous avez des questions liées aux pièces de rechange, et aux produits de piscine de Pentair Water Pool and Spa Products, veuillez utiliser les coordonnées suivantes. Service Clients (8h00 à 17h00 heure normale du Pacifique) Téléphone: (800) 831-7133 (appuyez sur la touche trois de la messagerie) Télécopie: (800) 284-4151 Support Technique pour Pentair Water Pool and Spa, Inc.
Table des matières Section I. Identification du chauffe-eau ................................................................... 44 Section II. Introduction .............................................................................................. 45 Consignes importantes .............................................................................................................................................................. 45 Information sur la garantie ........................................
Section I. Identification du chauffe-eau 44 INFORMATION POUR L'IDENTIFICATION DU CHAUFFE-EAU Pour identifier le chauffe-eau, voir la plaque signalétique à l'intérieur du panneau avant de l'appareil. Il y a deux codes indicateurs pour chaque chauffe-eau, le numéro de modèle et le numéro d'identification (HIN). a.
Section II. 45 Introduction Introduction MiniMax® NT Chauffes-eau pour piscine et spa Félicitations pour l'acquisition de votre de votre système de chauffage haute performance MiniMax NT. Vous pourrez profiter de votre nouveau système de chauffage pendant des années si vous suivez bien les consignes d'installation et d'utilisation, ainsi que les consignes d'entretien et d'équilibre chimique de l'eau.
Section II. 46 Introduction CONFORMITÉ AUX CODES L'installation doit être conforme aux codes locaux, ou, en leurs absences, au National Fuel Gas Code, ANSI Z 223.1/NFPA 54 et/ou CSA B149.1, Natural Gas and Propane Installations Codes. Le chauffe-eau, une fois installé, doit être raccordé à une prise de terre et fixé selon les codes locaux, ou en l'absence de ces codes, aux États-Unis, avec le National Electrical Code, ANSI/NFPA 7 ; au Canada, avec le Code canadien d'électricité, CSA C 22.1.
Section III. Installation 47 Consignes d'installations SPÉCIFICATIONS Ces consignes de montage sont destinées à être utilisées exclusivement par du personnel qualifié spécialement formé à l'installation de ce type d'équipement de chauffage et de ses composants. Certaines provinces exigent que l'installation et la réparation soient effectuée par un technicien titulaire d'un permis. Si tel est le cas, veuillez à ce que le service d'entretien avec lequel vous faites affaire soit dûment autorisé.
Section III. Installation 48 DÉRIVATION MANUELLE Là où le débit dépasse le taux maximum de 450 LPM (Litre par Minute), une dérivation manuelle doit être installée et ajustée. Après ces ajustements, la manette de la soupape doit être enlevée pour éviter toute manipulation. Voir Figure 2. VERS PISCINE CHAUFFE-EAU POUR PISCINE POMPE FILTRE DÉRIVATION MANUELLE Modèle Min. (LPM) Max.
Section III. Installation 49 RACCORDEMENTS DES CONDUITES D'EAU Collecteurs réversibles — Raccords d'entrée et de sortie réversibles Le MiniMax NT est assemblé en usine avec des raccords d'arrivée et de sortie d'eau sur le côté droit. Les collecteurs d'entrée et de sortie peuvent être inversées et placées sur le côté gauche sans retirer l'échangeur de chaleur.
Section III. Installation 50 Raccords d'entrée et de sortie réversibles, Sur la gamme de chauffe-eau MiniMax NT, il existe un isolant installée par l'usine situé sur le même côté que la tête de retour des chauffe-eau. Cette isolant existe pour que, si les têtes sont inversées sur le terrain pendant l'installation initiale du chauffe-eau, les commutateurs à limites supérieures soient protégés de la chaleur réfléchie à partir de l'accumulateur du conduit. suite 9.
Section III. Installation 51 RACCORDEMENT DES CONDUITES DE GAZ INSTALLATIONS DE LA CONDUITE DE GAZ Avant d'installer la conduite de gaz, vérifier le type de gaz pour lequel le chauffe-eau a été conçu. Ceci est important car différents types de gaz nécessitent des tailles de conduites différentes. La plaque signalétique sur l'appareil vous indique le type de gaz à utiliser pour ce chauffe-eau.
Section III. Installation 52 DIMENSION DES TUYAUX DE GAZ Tableau 2. MESURE DES TUYAUX POUR RACCORDS D’ARRIVÉE DE GAZ LONGUEUR MAXIMUM ÉQUIVALENTE DE TUYAUX (en mêtre) Gaz Naturel à 1000 B.T.U. par pied cube Propane à 2500 B.T.U. par pied cube 1.27 cm 1.905 cm 2.54 cm 3.175 cm 3.81 cm MODÉLE 200 5.08 cm 6.
Section III. Installation 53 VÉRIFICATION DE LA PRESSION DE GAZ Entrée Admission Approvisionnement d'air Approvisionnement d'air 1. Mettre l'interrupteur d'alimentation à la Entrée Admission position « OFF ». 2. Fermer la soupape de gaz « OFF ». 3. Enlever le bouchon NPT de 1/8 po situé sur le côté externe de la soupape et y visser le raccord que vous trouverez dans l'ensemble pour manomètre. 4. Connecter le tuyau du manomètre au raccord. 5. Ouvrir la soupape de gaz « ON ». 6.
Section III. Installation 54 VENTILATION INTÉRIEUR — Exigences Générales Le tuyau de ventilation doit être du même gabarit ou plus grand. Les chauffe-eau MiniMax NT sont capables de rotation de débit à 360 degrés et de fonctionner avec une pression statique à ventilation positive et une température de ventilation du gaz à moins de 400 °F (200 °C). La longueur totale du parcours à l'horizontal ne doit pas excéder la longueur mentionnée plus bas dans les tableaux.
Section III. Installation 55 INSTALLATION INTÉRIEURE (États-Unis Uniquement) INSTALLATION EXTÉRIEUR SOUS ABRIS (Canada) Se reporter page 56 pour les adaptateurs d'aération Tous les combustibles et gaz de ventilation doivent être entièrement évacués vers l'extérieur par l'intermédiaire d'une conduite de ventilation connectée à un adaptateur de canalisation.
Section III. Installation 56 ADMISSION D'AIR DE COMBUSTION Guide sur les exigences pour l'approvisionnement d'air pour les chauffe-eau MiniMax NT Pour l'installation intérieure, le chauffe-eau doit être placé dans un endroit où l'approvisionnement d'air est adéquat pour la combustion et la bonne ventilation de l'air environnant.
Rev. E 4-15-05 Support de fixation rapide 2 pi min. Plus de 10 pi Cheminée/Conduit d’aération à gaz Manchon de toit 3 pi min. Bouchon d'aération Peut utiliser un conduit d’aération mural unique avec des reliures soudées, des joints et des matériaux d’isolation adéquats. Doit être apte à un usage avec des appareils de catégorie III ayant des caractéristiques nominales de température de gaz de carneau de moins de 400 degrés F. (200 ˚C). Doit être du même diamètre que le raccord de conduit.
Section III. Installation 58 INSTALLATION EXTÉRIEURE (Pour l'installation extérieure sous abris au Canada, voir la page 55) Pour une installation extérieure avec une grille d'échappement, le chauffe-eau doit être placé dans un endroit adéquat et sur un sol incombustible au niveau. Ne pas installer le chauffe-eau sous un surplomb avec des dégagements de moins de 3 pi (90 cm) à partir du sommet du chauffe-eau. La zone située en dessous du surplomb doit être dégagée sur trois côtés.
Section III. Installation 59 RACCORDEMENTS ÉLECTRIQUES Classement électrique 60 Hz 120/240 Volts c.a. monophasé ATTENTION ! This heater is designed to operate at 120 or 240 VAC. It is not recommended to be connected to OR operate on a 208 VAC. À NOTER • Le chauffage MiniMax NT est pré-câblé pour une connexion AC de 240 volt en utilisant le connecteur "ROUGE" et le connecteur commun "BEIGE"; voir Figure 16 ci-dessous.
REMOTE CONTROL MANUAL FOR & INSTALLATION PR J5 J8 J6 J1 J2 GY SPA COM POOL J4 24V P4 W PR Y J7 TFUSE HLMT PRESS P7 JI0 VLV P10 R W BL THERMAL FUSE WIRING MUST BE REPLACED WITH 18 AWG, 600V, 150˚C TEMP. RATING. O J9 J11 IGN MOD P9 P11 W R MV MV GAS VALVE THERMAL FUSE IF ORIGINAL FACTORY WIRING MUST BE REPLACED, INSTALLER MUST SUPPLY UL/CSA APPROVED WIRE WITH 18 AWG, 600V, 105˚C TEMP. RATING.
Section IV. Fonctionnement 61 Consignes de Fonctionnement FONCTIONNEMENT GÉNÉRALE DU SYSTÈME 1. Amorcez la pompe, assurez-vous qu'elle fonctionne et qu'elle a été purgée, pour fermer le manostat et l'alimentation électrique au chauffe-eau. Assurez-vous que la piscine et/ou le spa est rempli à un niveau d'eau adéquat. Suivez les instructions pour l'allumage/Consignes de fonctionnement ci-dessous.
Section IV. Fonctionnement 62 CONTRÔLES DE SÉCURITÉ Figure 20. COMMUTATEUR (VENTILATEUR) DE PRESSION DU VIDE D'AIR Le commutateur de pression du vide d'air (voir figure 20) est un outil de sécurité utilisé pour s'assurer que le souffleur de combustion d'air fonctionne, et a été conçu pour contrôler la pression du vide (négative) à l'intérieur de la soufflerie. Le commutateur de pressions d'air est installé en usine et est connecté en amont du module d'allumage.
Section IV. Fonctionnement CONTRÔLES DE SÉCURITÉ, (suite) HAUTES LIMITES 63 Verification de l'alimentation de la flamme Une « Haute Limite » est un instrument qui ouvre le circuit électrique et ferme le chauffe-eau en se basant sur une position donnée de température enregistrée sur l'Instrument de « Haute Limite » .
Section IV. Fonctionnement 64 THERMOSTAT À AFFICHAGE NUMÉRIQUE TOUCHE DE COMMANDE À DISTANCE POWER REMOTE PRESSURE SW TÉMOINS INDICATEURS DU SYSTÈME POOL SPA THERMOSTAT TOUCHE PISCINE TOUCHE SPA OFF HEATING SERVICE TEMPERATURE SETTING POOL SPA PRESS ANY ARROW ONCE TO CHECK SET TEMPERATURE TOUCHE HORS TENSION TOUCHE POUR AUGMENTER LA TEMPÉRATURE TOUCHE DE PRÉ-RÉGLAGES POUR LA PISCINE ET LE SPA Figure 25.
Section IV. Fonctionnement 65 Figure 26. Rev.
Section IV. Fonctionnement 66 RÉGLAGE DU THERMOSTAT Le chauffe-eau MiniMax NT est livré avec les réglages d'usine pour piscine à 78 ºF (25 °C), pour spa à 100 ºF (37 °C) et en mode arrêt (OFF). Lorsque l'appareil est mis sous tension, le thermostat procède à une vérification interne de ses circuits. Durant cette vérification, l'écran affiche « 888 » en premier, ensuite « --- ». Ce processus dure environ dix (10) secondes. Les témoins DEL « Power » et « Off » s'allument, voir la figure 26. 1.
Section IV. Fonctionnement 67 • CHALEUR (HEAT) Le témoin de la chaleur s'allume à chaque fois que le thermostat est sollicité pour faire remonter la température. Cela initialise le circuit d'allumage — le témoin s'allume pour indiquer que la mise à feu des brûleurs principaux est réussie et restera allumé jusqu'à ce que la température de l'eau de la piscine et/ou spa est atteinte. • ENTRETIEN (SERVICE) Le témoin d'entretien est éteint tant que le chauffe-eau fonctionne normalement.
Section V. Dépannage 68 CONSIGNES DE DÉPANNAGE DÉPANNAGE (THERMOSTAT A AFFICHAGE NUMERIQUE) L'écran d'affichage du thermostat à affichage numérique possède trois témoins DEL avec un point décimal entre le premier caractère et le second. Cet écran indique également les codes d'erreur dans le cas de défaillance du système de contrôle du chauffe-eau ou d'une défaillance du thermostat. L'écran affiche la température actuelle ou une valeur de réglage ou OFF, tel que sélectionné par l'utilisateur.
Section V. Dépannage 69 CONSIGNES DE DÉPANNAGE CAUSE PROBABLE REMÈDE Le chauffe-eau ne démarre pas Le système automatique d'allumage est défaillant Vérifier que les branchements électriques soient bons et bien fixés. Si OUI, contacter le technicien d'entretien.
Section VI. Entretien 70 Consignes d'Entretien Il est recommande de vérifier les pièces suivantes au moins tous les six mois et au début de chaque nouvelle saison de baignade. 1. Examiner le système de ventilation. Vérifier qu'il n'y a aucune obstruction au débit d'air nécessaire à la combustion et à la ventilation. 2. Examiner visuellement le brûleur principal et le module d'allumage à surface chaude. La flamme doit être bleue. Si elle apparaît jaune, il faut vérifier et nettoyer les brûleurs.
Section VI. Entretien 71 FONCTIONNEMENT AU PRINTEMPS ET EN AUTOMNE Si la piscine n'est utilisée qu'occasionnellement, ne pas éteindre complètement le chauffe-eau. Mettre le thermostat sur 68°F (20 °C). Cela maintiendra la piscine et la terre environnante à une température assez chaude, et l'on pourra rétablir une température de baignade plus rapidement.
Section VI. Entretien 72 ÉQUILIBRE CHIMIQUE DE L'EAU LA RÈGLE : le pH doit être maintenu entre 7,4 et 7,6. Il est primordial de respecter un pH adéquat, voit tableau 15. EAU DE PISCINE ET DE SPA Si le pH devient trop élevé (alcalin), les effets suivants seront constatés : Le chauffe-eau de Pentair Pool Products a été spécialement conçu pour votre piscine ou votre spa, et vous permettra d'apprécier des années d'entretien facile, à condition de maintenir un bon équilibre chimique de l'eau.
PIÈCES DE REMPLACEMENT NT STD avec DDTC — (tous Modèles) NT TSI avec DDTC — (Modèles 200, 250 et 300) 29 36 30 31 33 34 35 Pour Modèle FOR STD STDONLY Seulement Rev.
! # $ # % & & :
! # $ # % & & :
PIÈCES DE REMPLACEMENT NT TSI avec DDTC — (Modèle 400 — Commençant avec le numéro de série 12040039) 1 2 3 4 5 6 7 8 37 9 36 10 35 11 34 12 33 32 13 31 14 30 15 29 28 16 27 18 17 19 20 21 22 23 24 25 26 38 39 40 46 P/N 472235 45 44 43 42 41 Rev.
] $ ^ # K _ [` ` _ < $ @ J % % K % [ ; $ !" # $% !" &% !" * !" +%<# < =% " # >< "= ?%!" * * +%! < " # < " %! @%
ANNOTE P/N 472235 Rev.
ANNOTE Rev.
VEUILLEZ CONCERVER CE GUIDE D'INSTRUCTION. Pentair Water Pool and Spa, Inc. 1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000 10951 W. Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400 P/N 472235 Rev.