MSDS

M A T E R I A L S A F E T Y D A T A S H E E T

PERGO FINISHING PUTTY Page: 1

PRODUCT NAME: PERGO FINISHING PUTTY HMIS CODES: H F R P

PRODUCT CODE: CF1000 1 0 0

================ SECTION I - MANUFACTURER IDENTIFICATION =================

MANUFACTURER’S NAME: COLOR CAULK INC.

ADDRESS : 1105 S. Frontenac Rd.

Aurora, IL 60504

CHEMTREC : 800-424-9300 (Outside USA) 703-527-3887

EMERGENCY PHONE : 800-552-6225 DATE REVISED : 01/29/2003 Reviewed 4/19/2010

INFORMATION PHONE : 800-552-6225 NAME OF PREPARER : Thomas H. Jones

========= SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION ========

VAPOR PRESSURE WEIGHT

REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT

ACRYLIC COPOLYMER MIXTURE LESS THAN 50%

TITANIUM DIOXIDE 13463-67-7 LESS THAN 5%

PROPYLENE GLYCOL 57-55-6 0.08/20C LESS THAN 5%

* MINERAL SPIRITS 8052-41-3 LESS THAN 1%

2,2,4-Trimethyl-1,3-pentanediol Monoisobutyrate 25265-77-4 LESS THAN 5%

Indicates toxic chemical(s) subject to the reporting requirements of section

313 of Title III and of 40 CFR 372.

All ingredients in this product are included on the U.S. TSCA list and the Canadian

DSL.

============= SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ============

BOILING RANGE: NO DATA SPECIFIC GRAVITY (H2O=1):1.5-1.6

VAPOR DENSITY: N/A EVAPORATION RATE: <1 (butyl acetate = 1)

VISCOSITY:160K-320K CPS MATERIAL V.O.C.: 60 g/l

SOLUBILITY IN WATER: Dilutable

APPEARANCE AND ODOR: White paste-like substance, slight acrylic odor

=============== SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==============

FLASH POINT: Non-flammable METHOD USED: N/A

FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: N/A UPPER: N/A

EXTINGUISHING MEDIA: Foam, Carbon Dioxide or Dry chemical

SPECIAL FIREFIGHTING PROCEDURES: None

UNUSUAL FIRE AND EXPLOSION HAZARDS: None

======================= SECTION V - REACTIVITY DATA =======================

STABILITY: Stable

CONDITIONS TO AVOID: Heat; onset of decomposition is 177C/350F

INCOMPATIBILITY (MATERIALS TO AVOID): Avoid contact with strong oxidizing agents

HAZARDOUS DECOMPOSITION OR BYPRODUCTS: Thermal decomposition may yield carbon monoxide

or carbon dioxide

HAZARDOUS POLYMERIZATION: will not occur

PAGE 1
MATERIAL SAFETY DATA SHEET PERGO FINISHING PUTTY Page: PRODUCT NAME: PERGO FINISHING PUTTY 1 HMIS CODES: H F R P PRODUCT CODE: CF1000 1 0 0 ================ SECTION I - MANUFACTURER IDENTIFICATION ================= MANUFACTURER’S NAME: COLOR CAULK INC. ADDRESS : 1105 S. Frontenac Rd. Aurora, IL 60504 CHEMTREC : 800-424-9300 (Outside USA) 703-527-3887 EMERGENCY PHONE : 800-552-6225 DATE REVISED : 01/29/2003 Reviewed 4/19/2010 INFORMATION PHONE : 800-552-6225 NAME OF PREPARER : Thomas H.
PAGE 2
MATERIAL SAFETY DATA SHEET PERGO FINISHING PUTTY Page: 2 ==================== SECTION VI - HEALTH HAZARD DATA ===================== PRIMARY ROUTE OF ENTRY: Skin contact, eye contact, Ingestion INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Vapor can cause irritation of the nose, throat, lungs and can cause headache and nausea SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Slightly irritating to the eyes. May irritate skin upon repeated or prolong contact.
PAGE 3
MATERIAL SAFETY DATA SHEET PERGO FINISHING PUTTY Page: 3 ===================== SECTION VIII - CONTROL MEASURES ===================== RESPIRATORY PROTECTION Use OSHA/NIOSH approved respirator where exposure limits are exceeded or in poorly ventilated areas. VENTILATION Good general ventilation should be sufficient. Mechanical local exhoust ventilation at point of contaminant release.