PERLICK SELF-CONTAINED ICE MAKER MODEL: H50IM PRODUCT MANUAL
IMPORTANT 1. This booklet is an integral and essential part of the product and should be handed over to the user. Read the warnings contained in this booklet carefully as they give important indications regarding the safety of the installation, use and maintenance. Please preserve this booklet for any further consultation that may be necessary. 2. This Ice Maker should be destined only to the use for which it has been expressly conceived. Any other use should be considered improper and therefore dangerous.
I. GENERAL INFORMATION Top Panel 1.
II. INSTALLATION AND OPERATING INSTRUCTIONS 1. CHECKS BEFORE INSTALLATION * Visually inspect the exterior of the shipping container, and any severe damage noted should be reported to the carrier. WARNING Remove shipping tape(s) and packing as follows. If any are left in the Ice Maker, it will not work properly. IMPORTANT 1. Remove shipping tape holding the Door. 2. Ensure all components, fasteners and thumbscrews are securely in place. * Remove the package containing accessories.
2. LOCATION WARNING Normal operating ambient temperature should be within 45°F (7°C) to 100°F (38°C); Normal operating water temperature should be within 45°F (7°C) to 95°F (35°C). Operation of the Ice Maker, for extended periods, outside of these normal temperature ranges may affect production capacity. For best operating results: * The Ice Maker should not be located next to ovens, grills or other high heat producing equipment. * The location should provide a firm foundation for the equipment.
4. SET UP 1) Unpack the Ice Maker, and remove all shipping cartons, tapes and packing BEFORE operating the unit. Be careful not to damage the exterior panels when handling the Ice Maker. 2) Position the Ice Maker in a selected site. Clean the interior with soap and water and rinse thoroughly. 3) Level the Ice Maker in both the left-to-right and the front-to-rear directions. BUILT-IN INSTALLATION [a] CHECKING INSTALLATION SITE Ensure 15" (381mm) wide space for building in the Ice Maker.
3) To build in between a unit and an open space: Cabinet Min. 34" 4 7/8" 15" Fig. 3 Use a cabinet or the like to support the counter before building in the Ice Maker. Do not build in the Ice Maker at a corner where the Door will hit other equipment such as an oven handle or where the Ice Maker cannot be pulled out for service. 4) To build into an L-shaped kitchen: Mi n. 23 " Oven Fig. 5 Ice Maker Fig. 4 [b] BUILDING IN THE ICE MAKER 1) Make water supply and drain connections.
5. WATER SUPPLY AND DRAIN CONNECTIONS WARNING To prevent damage to the freezer mechanism, do not operate this Ice Maker when the water supply is OFF, or if the pressure is below 10 PSIG (0.7 bar), the recommended water pressure. Stop the Ice Maker until proper water pressure is resumed. * Attach the brass fitting included in the accessory bag as shown in Fig. 5. The brass fitting size is a 1/2" FPT and must be connected only to a potable water supply.
6.
8. PREPARING THE ICEMAKER FOR LONG STORAGE WARNING Drain the Ice Maker to prevent damage to the water supply line at subfreezing temperatures, using air or carbon dioxide. Shut off the Ice Maker until proper air temperature is resumed. 1) Close the Water Supply Line Shut-off Valve, and open the Drain Valve. 2) Move the Control Switch to the “OFF" position. 3) Blow out the water supply line and the internal water circuit.
III. Cleaning and Maintenance IMPORTANT 1. Ensure all components, fasteners and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. 2. Wash your hands before removing ice. Use the scoop provided to remove ice. 3. Keep the scoop clean. Clean it by using a neutral cleaner at least once a day, and rinse thoroughly. 4. Close the bin door after removing ice to prevent entrance of dirt, dust or insects into the bin. 5.
[b] Cleaning Procedure The cleaning process will remove lime deposits from the water system. 1) Remove all ice from the evaporator and the storage bin. Note: To remove cubes on the evaporator, move the control switch to the “OFF" position and move it back to the “ICE" position after 3 minutes. The defrost cycle starts and the cubes will be removed from the evaporator. 2) Move the control switch to the “OFF" position. Close the water supply line shut-off valve.
10) Remove the water tank, drain it, and replace it as described in 3) through 6). 11) Open the water supply line shut-off valve. 12) Move the control switch to the “WASH" position to circulate clean water for about 5 minutes. 13) Move the control switch to the “OFF" position, then remove the water tank, drain it, and replace it as described in 3) through 6). 14) Repeat 12) and 13) three more times to rinse thoroughly. [c] Sanitizing Solution Dilute 0.5 fl. oz. (14.8 ml or 1 tbs) of 5.
Water Tank 6) Disconnect the suction tube by compressing both plastic tabs to unlock Suction Tube the joint in the direction of the black arrows and pulling the tube clear to drain the tank. Joint 7) Spread out the tabs on both sides to unlock the water tank, and pull it out toward you. Soak the water tank in the sanitizing solution for 10 minutes. Unlock Drain Unlock Frame Pipe 8) Lift off the ice chute from the front frame pipe and then from the rear frame pipe.
Bracket 12) Slide in the spray assembly along the rails on Frame Pipe the right and left brackets. Refit the discharge tube securely on the spray assembly. A loose Rail fitting may cause a water leak. Rail 13) Position and lock the ice chute onto the front and rear frame pipes by pushing the chute down until it clicks onto both pipes. 14) Slide in the water tank along the rails at the bottom of the right and left brackets until it clicks into place.
20) Mix a new batch of the sanitizing solution and slowly pour it into the water tank. 21) Move the control switch to the “WASH" position. 22) After circulating the sanitizing solution for about 15 minutes, move the control switch to the “OFF" position. Water Tank 23) Disconnect the suction tube by compressing Suction Tube both plastic tabs to unlock the joint in the direction of the black arrows and pulling the tube clear.
29) Move the control switch to the “WASH" position to circulate clean water for about 5 minutes. 30) Move the control switch to the “OFF" position, then remove the water tank, drain it, and replace it as described in 23) through 26). 31) Repeat 29) and 30) two more times to rinse thoroughly. 32) Move the control switch to the “ICE" position, and start the automatic icemaking process. 2.
PERLICK H50IM ICE MAKER LIMITED WARRANTY ENTIRE PRODUCT- Full One Year Warranty: For one year from the date of original installation, Perlick Corporation’s warranty covers all parts and labor to repair or replace any part of the product, which proves to be defective in material and workmanship. TERMS: The Perlick Warranty applies to products installed in the fifty United States, the District of Columbia or the ten provinces of Canada.
