Specification Sheet

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex

Super Weatherstrip
Adhesive
AAM Revised 09/02
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION S.I.N.: 834-300
Permatex

Super Weatherstrip Adhesive is a viscous liquid
contact type cement for all types of weatherstripping and
general purpose bonding. Super Weatherstrip Adhesive is an
air-drying contact cement that allows quick bonding yet
maintains enough versatility in tack to allow large areas to be
spread and bonded at one time. The drying characteristics
allow for repositioning parts after contact is made. The
maximum strength of Super Weatherstrip Adhesive is attained
after all the solvent has been released. Non-porous surfaces,
if assembled while the adhesive is wet, will prevent the release
of solvent, consequently, the adhesive will take longer to dry
and develop maximum strength.
PRODUCT BENEFITS
• Water resistant
• Excellent chemical resistance
• Fast drying
• Withstands temperature extremes
TYPICAL APPLICATIONS
• Auto carpeting
• Door and trunk moldings
• All types of automotive weatherstripping
• Vinyl tops
• Fabric backed vinyl upholstery
DIRECTIONS FOR USE
1. Clean surfaces thoroughly. Use abrasives to remove
any powdery mold release from the new
weatherstripping.
2. Apply a thin, even film to both surfaces.
3. Allow to dry until the surfaces are tacky (about 3-4
minutes).
4. Bond the two surfaces together, and apply enough
pressure to produce uniform contact.
Note: The early strength of Super Weatherstrip
Adhesive is enough to hold most parts together.
However, maximum strength is obtained after the
adhesive is completely dry. Aging of the bond and
exposure to moderate heat increases strength.
For Cleanup
1. Use lacquer thinner or any hydrocarbon solvent while
still wet.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type Neoprene Rubber
Appearance Black viscous liquid
Odor Solvent
Specific Gravity 0.88
Flash Point, TCC, °F -10
TYPICAL CURING PERFORMANCE
Tack free time is 3-4 minutes. Substantial bond will form when
the surfaces are mated. Maximum strength is obtained after
the adhesive is completely dry. Force drying with moderate
heat will increase strength. Cure times will vary with
temperature, humidity and gap.
TYPICAL ENVIRONMENTAL RESISTANCE
Temperature Resistance
Typical Values
Continuous, °C (°F) -54 to 204 (-65 to 400)
Chemical / Solvent Resistance
The product retains effective properties in contact with
automotive fluids, such as motor oil, transmission fluids,
alcohol and antifreeze solutions.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
an adhesive for chlorine or other strong oxidizing
materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number Container Size
80638 (80BR) 2 5 fl. oz. tube, carded
81731 (80) 5 fl. oz. tube, boxed
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8°
to 28°C
(46°
to 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.