User guide

ManualsBrandsphil&teds ManualsProducts for childrencolumbus

ISO CERTIFIED FACTORY

FITTING INSTRUCTIONS

CHILD CAR SEAT

Suitable for 9kg to 36kg

GROUP 1+2+3

(9 months to 11 years approx)

NOTICE

1. This is a "Universal" child restraint; it is approved to ECE

Regulation 44.04 for general use in vehicles and will fit most, but

not all, vehicle seats.

2. A correct fit is likely if the vehicle manufacturer has declared in

the vehicle handbook that the vehicle is capable of accepting a

"Universal" child restraint for this group.

3. This child restraint has been declared "Universal" under more

stringent conditions than those applied to earlier designs which

do not carry this notice.

4. If in doubt, consult either the child restraint manufacturer or

the retailer.

Only suitable if the vehicle is fitted with 3-point static, 3-point

retractor safety belts, approved to UN/ECE Regulation No. 16 or

other equivalent standards.

Summary of content (10 pages)

PAGE 1
ISO CERTIFIED FACTORY ISO CERTIFIED FACTORY ISO CERTIFIED FACTORY CHILD CAR SEAT GROUP 1+2+3 Suitable for 9kg to 36kg (9 months to 11 years approx) FITTING INSTRUCTIONS NOTICE 1. This is a "Universal" child restraint; it is approved to ECE Regulation 44.04 for general use in vehicles and will fit most, but not all, vehicle seats. 2.
PAGE 2
WARNINGS THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. ! PLEASE READ THOROUGHLY BEFORE COMMENCING INSTALLATION AS AN INCORRECT INSTALLATION COULD BE DANGEROUS. ! This child seat can be used with the harness for children of 9 to 18kg in weight(approx. 9 months to 4 years) ! This child seat can be used without the harness for children of 15 to 36kg in weight.(approx.
PAGE 3
PART S AN D FITTING S Headrest Belt guide Belt guide Backrest Slot Harness Red botton Chest pad Buckle Movable armrest Ha rne ss ad ju st er l eve r Seat belt route slot Comfort pad Belt guide Seat cushion Harness adjuster strap Belt guide D - ri ng D - ri ng Harness straps D - ri ng D - ri ng Harness connector THE TYPE OF APPROVED SEAT BELT YOU MUST HAVE Your child seat can only be installed forward facing using a three-point lap and diagonal seat belt in the front or rear passenger seats
PAGE 4
CARE AND MAINTENANCE Assembling illustration Step 1 Step 2 Step 3 INSTALL STEP Step 1: Put down the armrest until the red button pops out. Step 2: Keep the backrest (With arm rests) in level line, completely press the backrest both bottom circular part into the booster base corresponding column holes. Step 3: Rotate it into vertical position, until hear the “Click”, then finish.
PAGE 5
CORRECT SHOULDER STRAP HEIGHT NO-Too low NO-Too high YES-Correct Always check that the shoulder straps are at the correct height for your child. The child’s shoulders should always be below the slot for the harness. CHANGING THE SHOULDER STRAP HEIGHT Gr.15kg+ Gr.9kg+ Firstly, release the strap holding the backrest cover on to gain access to the harness. Slide one of the harness straps off the harness connector.
PAGE 6
REMOVING ALL STRAPS REMOVING THE SAFETY HARNESS SHOULDER STRAPS Release the strap at the bottom of the backrest cover to gain access to the harness. Slide both of the harness straps off the harness connector at the back of the backrest and pull the webbing through the slots in the seat’s backrest and fabric cover. REMOVING THE SAFETY HARNESS LAP STRAPS Turn the webbing retainers on their narrowest end and feed them through the slots in the base of the seat and then through the slots in the fabric cover.
PAGE 7
FASTENING THE SAFETY SEAT BUCKLE STEP.1 STEP.2 STEP.3 Step1. Slot the two metal sections of the buckle connectors together. Step2. Insert the two buckle connectors into the slot at the top of the buckle until you hear “click” . Step3. Always check the harness is correctly locked by pulling the shoulder straps upwards. To release the harness, press the red button on the buckle downwards.
PAGE 8
FITTING THE CAR SEAT WHEN USING THE HARNESS Installation Steps: 9-18kg (approx. 9 months to 4 years) Step1 . Place the child safety seat on the vehicle’s seat ensuring it is firmly pressed against the car seat backrest . 1 2 Step2 . Fasten the seat belt into the seat belt buckle . 3 Step3 . Thread the lap belt goes from the two red D-Ring by the armrests. 4 Step4 . Then pull the lap belt between the two red D - Ring in a suitable length so that this lap belt can go around the front of the seat .
PAGE 9
FITTING THE CAR SEAT WHEN ONLY USING THE 3- POINT SEAT BELT 2 Pu ll 15-36kg 1P re ss (approx. 3years to 11 years) According to children’s different height, the headrest can be adjusted up and down. To make sure that the position fits for your child. 1 3 2 DIAGONAL BELT 4 LAP BELT Step1. Place the child safety seat on the vehicle’s seat ensuring it is firmly pressed against the car seat backrest. Step2.
PAGE 10
CARE AND MAINTENANCE THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. BACKREST COVER REMOVAL. First, release the elastic strap at the bottom of the backrest cover, Slide the cover off. The covers can now be cleaned. HEADREST, BOOSTER SEAT COVER REMOVAL. Slide the cover off. The covers can now be cleaned. THE COVER SHOULD BE HAND WASH. Use only a mild hand soap and warm water. Do not use chemical cleaners and never attempt to bleach or dye the webbing.