Manual

Unpacking your Buggy
On arrival and setting up for the first time • Your buggy (frame and fabric items) will arrive in a box. Check the
box is not damaged.
• The initial setup involves installing: wheels, front wheel J-Bar,
footplate, fabric items & handle.
Don’t worry - it’s easy - no tools needed.
Put the wheels on Lie box on floor (TOP up). Carefully cut tape and lift off top. Check that all components purchased are in the box. Check no components appear damaged. Carefully lift out wheels (2 rear and one front), bacpac and frame. Place frame on floor, clicking auto-locks (A & B) in place. Refer diagram above. Attach the rear wheels by sliding each axle through the axle tubes. Depress the ‘nib spring’ on each axle. Ensure nib pops out once through axle. These hold the wheels in place. Remove wheels as required. Attach front wheel: Pull swivel wheel lock on pipe out (refer diagram); aim J-bar to the side not front; depress nib spring and insert J-bar into pipe; ensure nib spring pops at top and J-bar is flush with plastic bush; push cap over pipe top. Reverse procedure as required. Put the parcel tray on Pull the parcel tray forward so that it is in line with the ground. Loop straps 1 & 2 (on both sides) around frame. Ensure strap 1 does not catch the auto-lock pin. There is a snap on the inside of the frame below the auto-lock. Loop strap 1 below this snap. Loop the straps in the centre of the tray (both sides) around the frame below doubles bar tube. Attach rear strap 3 around the vertical frame at back of buggy. Check it looks the same as the diagram. Do not place more than 3kg/7lbs in the parcel tray.
Put the handle on Slide the handle onto the frame. Ensure the holes in the handle face down. There are two height settings. Depress the nib springs on undersides of frame (twice for the lower setting).
1
Put the footplate on Position footplate over front of buggy frame. Insert 4 plastic rivets through holes in footplate; match to holes in frame. Rivet must rest on footplate. DO NOT push stalk until rivet rests on footplate. Push (or tap) rivet centre stalk, until flush.
2
3
5
Accessories
Call your Most Excellent Dealer for Accessories and Prices
J Bar
swivel wheel autolock on pipe out
4
Explorer sleeping bag Un-clip the breastplate.Thread the safety harness through the 5 slots in the back of the sleeping bag. Attach the safety harness to the breastplate. Fold down the front of the sleeping bag as required. The sleeping bag top can be removed completely and the base used as a buggy liner in warmer weather. Remove the liners for separate washing. Follow fabric care label for washing sleeping bag. Colours: Black or Blue
Travel bag These bags help protect Kiwi Explorer Buggy
TM
. Remove the rear
wheels and place (axle-to-axle) together. Place Kiwi Explorer Buggy
TM
in the travel bag and zip up bag. Carry with the shoulder or
hand straps. Because the fabric has a waterproof layer, storage of a damp/wet Kiwi Explorer Buggy
TM
for long periods may result in
fabric mildew. Air dry. Colours: Black
Kiwi Explorer mattress Made from the same fabric as the buggy, the mattress fits the base of the newborn fitting. Guide the safety harness around the mattress. Use the safety harness in the usual way. The mattress can be used in the sitting position for extra back support and comfort. Remove the mattress for cleaning. Fabric care as with buggy fabric.
Kiwi Explorer bacpac Made from the same durable fabric as the buggy, great for extra storage and security. Attaches to the buggy (upper handle and lower frame) with quick-release clips. Internal PVC compartment for soiled items. Shoulder straps allow you to carry goods separate from the buggy. Embroidered with Kiwi Explorer. Removed easily for cleaning. Fabric care as with buggy fabric.
Kiwi Explorer sun-insect mesh Mesh protects from insects, wind and sun (SPF 6.5) Fits same as storm cover.
Child Lifter Sits in newborn position of buggy. Has a firm base and attaches using snap fasteners. Attach 5-point safety harness around child lifter. Sleeping baby can be lifted from the buggy using two handles. Made from the same durable fabric as the buggy and comes in matching colours.
A
B
3
doubles bar tube