Real Flat Television User Manual 21PT5006 29PT5006 25PT5016 29PT5016 21PT5026 29PT5026 PHI
CONTENTS Introduction Safety information / Tips ....................................................................................................... 3 Before calling service ............................................................................................................ 4 Basic Installation functions TV hookup (Basic connection) ........................................................................................... 5 Remote control use and care ...........................................
SAFETY INFORMATION AND USEFUL TIPS Safety information • Disconnect mains plug when : – the red light below the TV screen is flashing continuously. – a bright white line is displayed across the screen. – cleaning the TV screen. Never use abrasive cleaning agents. Use a slight damp chamois leather or soft cloth. – there is a lightning storm. – the set is left unattended for a prolonged period of time. • No naked flame sources, such as lighted candles, should be placed on top of the TV or in the vicinity.
BEFORE CALLING SERVICE Below is a list of frequently occurred symptoms. Before you call for service, make these simple checks. Some of these symptoms can easily be rectified if you know what to do. Symptoms What you should do Colour patch (uneveness) • Switch off the TV by the mains power button.Wait for 20 minutes before switching on again. • Check the TV is not placed too near speakers or magnetic objects. No power • Check the TV’s AC power cord is plugged into the mains socket.
TV HOOKUP (BASIC CONNECTION) Antenna connection • Connect the aerial plug to the antenna socket on the backcover. • Insert the mains plug into the wall socket. Mains connection • For correct mains voltage, refer to type sticker at the rear of the TV set • Consult your dealer if mains supply is different. Note :This diagram is not representative of the actual plug and socket. Switching on the set • Press the main power button to switch on/ off theTV.
AUDIO/VIDEO CONNECTIONS (PLAYBACK) Monitor out AV1 in AV2 in VIDEO AV sockets on rear of TV Y L/Mono AUDIO R Pr COMPONENT VIDEO INPUT OUT Y Pb S-VIDEO Pb OUT Pr L AUDIO Back of DVD R DVD (with “Y” , “Pb” and “Pr” and Output sockets) You can view the playback of DVD discs by using the COMPONENT VIDEO INPUT (CVI) sockets on the rear of the TV. – Connect the CVI cables from the “Y”, “Pb” and “Pr” INPUT of the TV to the “Y”, “Pb”and “Pr” OUTPUT of the DVD to view playback of DVD discs.
AUDIO/VIDEO CONNECTIONS (PLAYBACK) Monitor out AV1 in AV2 in VIDEO Y L/Mono S-VIDEO Pb AUDIO R AV sockets on the rear of TV Pr COMPONENT VIDEO INPUT OUT OUT ANTENNA VIDEO IN IN Back of VCR OUT R AUDIO L IN VCR (with Video and Audio output sockets) You can view the playback of VCR tapes (Video Disc players, camcorders, etc.) by using the AUDIO and VIDEO INPUT sockets on the rear of the TV.
AUDIO/VIDEO CONNECTIONS (RECORDING) Connection for recording from the TV channel Monitor out AV1 in AV2 in VIDEO Y L/Mono R S-VIDEO Pb AUDIO AV sockets on the rear of TV Pr COMPONENT VIDEO INPUT OUT OUT ANTENNA VIDEO IN IN OUT R AUDIO L IN VCR (with Video and Audio input sockets) – Connect the video and audio RCA cables from the INPUT sockets of the VCR to the MONITOR OUT on the rear of the TV.
REMOTE CONTROL FUNCTIONS (Refer to the correct page for the remote control that came with your set) Standby Lets you place the TV set on standby. To turn on the TV, press CH + or –, , AV, A/CH or digit keys. Personal Zapping You can surf up to 10 personal channels for each key (p. 26) Sleeptimer To select a time period after which the set switch to standby mode automatically. POWER Delete Personal Zapping list Deletes stored channels from Personal Zapping list (p.
REMOTE CONTROL FUNCTIONS (Refer to the correct page for the remote control that came with your set) Teletext /Personal Zapping In teletext mode; the colour keys allows direct access to an item or corresponding pages (p 27-28) In Personal Zapping mode; you can surf up to 10 personal channels for each key (p. 26) Standby Lets you place the TV set on standby. To turn on the TV, press CH + or –, , AV, A/CH or digit keys Teletext keys (p.
TV CONTROL FUNCTIONS The TV controls are on the front or the side of the set depending on your model. & Mains Power button Switches mains power on or off. é Standby light indicator Indicator is lit when standby mode is activated. “ Remote Sensor Acts as a sensor for activating the controls of the TV when remote control handset is aimed at it. ‘ Volume + / – buttons Adjust sound volume softer/louder. ( Channel œ/o buttons Select channel in descending/ascending order.
MENU LANGUAGE SELECTION Operating instructions generally explains the operation of the TV set using the buttons on the remote control unless otherwise stated. Please read the following instructions carefully and follow the stopes as shown to familiarise yourself with the installations and all features available in your set. Tip: When there is no signal input to the TV, you may encounter instability of the on screen display.
AUTOMATIC TUNING OF CHANNELS Automatic tuning of channels allows you to store each programme automatically. Step Press button Result on screen Enter main menu Press button repeatedly until Install is selected. Enter the Install menu. Select Auto Store. Start automatic tuning of channels. When tuning is completed, exit menu from screen. Screen displays may look different on certain models.
MANUAL TUNING OF CHANNELS Manual tuning of channels allows you to select your preferred channel number for every available programme. Step Press button Result on screen Enter main menu. Press button repeatedly until Install is selected. Enter the Install menu. Press button repeatedly until Manual Store is selected. Enter the Manual Store menu. Press button repeatedly until Search is selected. Screen displays may look different on certain models.
MANUAL TUNING OF CHANNELS Step Press button Result on screen Start manual searching. Searching stops once a transmitting signal is found. Select Channel. Key in the channel number. Press button repeatedly until Store is selected. Store the tuned channel. Note : If you want to continue searching for another transmitting channel, repeat steps 7 to 11. Exit menu from screen. Screen displays may look different on certain models.
COLOUR / SOUND SYSTEM This feature allows you to select your desired Colour and Sound system. If Auto is selected, the respective colour and sound system will be automatically selected according to the transmission system. Note: Select your desired colour and sound system manually if reception is poor in Auto mode. Step Press button Repeat steps 1 to step 5 as in “Manual Tuning of TV Channels” Result on screen Colour System is selected. or Select the desired colour system (Auto, PAL, NTSC 3.
FINE TUNING OF CHANNELS This feature allows you to adjust picture reception in areas of weak reception. Step Press button Result on screen Enter main menu. Press button repeatedly until Install is selected. Enter the Install menu. Press button repeatedly until Manual Store is selected. Enter the Manual Store menu. Press button repeatedly until Fine Tune is selected. or Fine tune until the best reception is obtained. Select Store. Store last fine-tuned status. Exit from menu screen.
CHANNEL EDIT This feature allows you to skip or edit channels which have bad or weak TV signal or channels that you do not watch often. Note: Once a channel is skipped, you cannot access it by using the CH (Channel) + or – button.You can only access it using the channel digit (0 - 9) buttons. Step Press button Result on screen Enter main menu. Press button repeatedly until Install is selected. Enter the Install menu. Press button repeatedly until Channel Edit is selected. Enter the Channel Edit menu.
PICTURE ADJUSTMENTS The picture menu allows you to make adjustments to the picture. Step Press button Result on screen Enter main menu. Enter Picture menu. Select item. or or Adjust level or select desired setting. Exit menu from screen. Screen displays may look different on certain models. Picture menu items Activities Brightness Increase or decrease brightness level. Colour Increase or decrease colour level. Contrast Increase or decrease contrast level.
SOUND ADJUSTMENTS The sound menu allows you to make adjustments to the sound. Step Press button Result on screen Enter main menu. Select Sound menu. Enter Sound menu. or or Select item. Adjust level or select desired setting. Screen displays may look different on certain models. Exit menu from screen. Sound menu items Activities Treble Increase or decrease high frequency level. Bass Increase or decrease low frequency level. Balance Increase or decrease to adjust balance level.
FORMAT ADJUSTMENTS You can have a choice of two formats for your viewing pleasure, namely : -4:3 mode and the EXPAND 4:3 mode through the FORMAT menu. Step Press button Result on screen Enter main menu. Press button repeatedly until Features is selected. Enter the Features menu. Press button repeatedly until Format is selected. Press the button repeatedly to cycle through the different formats (4:3 or Expand 4:3) or and select your desired format. Exit menu from screen.
SIGNAL STRENGTH The Signal Strength feature allows to view the signal strength level when the On option is selected.The signal strength level will be indicated at the bottom of the screen whenever you switch channel. Step Result on screen Press button Enter main menu. Press button repeatedly until Features is selected. Enter Features menu. Press button repeatedly until Signal Strength is selected. Press button to select On option to activate the Signal Strength mode. Exit menu from screen.
ACTIVE CONTROL This Active Control feature automatically adjust settings for optimal picture quality continuously under any signal conditions.To activate the Active Control feature, select the “ON” option in the Active Control menu. Step Result on screen Press button Enter main menu. Press button repeatedly until Features is selected. Enter Features menu. Press button repeatedly until Active Control is selected. Press the button to select On option to activate Active Control mode.
SMART PICTURE Whether you are watching a movie or video game, your TV has automatic video control settings matched to your current program source or content.The Smart Picture feature quickly resets your TV’s video controls of program for a number of different types of programs and viewing conditions you may have in your home. Each Smart Picture setting is preset at the factory to automatically adjust the TV’s Brightness, Colour, Picture and Sharpness levels.
SMART SOUND Whether you are watching a movie or video game, your TV has automatic sound control settings matched to your current program source or content.The Smart Sound feature quickly resets your TV’s sound controls of program for a number of different types of programs and viewing conditions you may have in your home. Each Smart Sound setting is preset at the factory to automatically adjust the TV’s Treble and Bass levels.
PERSONAL ZAPPING A list or series of favourite TV programs can be selected and stored in the 4 coloured buttons with the Personal Zapping feature. With this feature you can easily viewed up to a total of 10 preferred channels for each coloured button. Adding Channels to the favourite list Step Result on screen Press button Select a channel with the Digit buttons. Press button to display list. Choose your favourite colour button to store selected channel.
TELETEXT (Available on certain models only) If a TV channel broadcast contains teletext information, each channel that broadcasts teletext transmits a page (index page) with information on how to use the teletext system, usually on page 100.The system transmitted is indicated in the option line at the bottom of the screen. Press button Result on screen On/Off teletext and superimpose teletext page over TV programme. Press the button once to switch on teletext display.
TELETEXT (Available on certain models only) Press button Result on screen Interrupt Press the button to change to TV mode. Press the button again to return to teletext mode and to the teletext page. Enlarge Press the button once to enlarge and view the top half of the page. Press the button the second time to enlarge and view the bottom half of the page. Press the button the third time to return to normal sized page. Hold A selected page sometimes contains a few sub-pages.
SPECIFICATIONS Product type 21PT5006 29PT5006 25PT5016 21PT5026 29PT5026 Picture Display screen type Real Flat picture tube Diagonal screen size 55 cm 72 cm 63 cm 55 cm 72 cm Visible diagonal screen size 51 cm 68 cm 59 cm 51 cm 68 cm Aspect ratio 4:3 Picture enhancements Active Control Picture noise reduction Noise Reduction Sound Loudspeakers 2 x 5W Sound systems AV stereo Full Stereo Sound features AVL, Mute, Smart Sound (4 modes) AVL, Mute, Smart Sound (4 modes), Dynamic
SPECIFICATIONS Product type 21PT5006 29PT5006 25PT5016 21PT5026 29PT5026 General 100-250V / 50-60 Hz Mains volt/freq. Power consumption 54 W 73 W 63 W 54 W 73 W Net weight 21 kg 42 kg 29 kg 21 kg 42 kg 23.5 kg 47.5 kg 33 kg 23.5 kg 47.5 594 x 460 x 486 740 x 583 x 484 662 x 527 x 451 594 x 460 x 486 740 x 583 x 484 Gross weight Set dimensions (W x H x D) mm Note: Specifications subject to change without notice.
Specifications are subject to change withoutnotice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. 2004 © Koninklijke Philips Electronics N.V. All rights reserved. www.philips.