e-Manual Philips LCD Monitor Electronic User’s Manual file:///D|/My%20Documents/dfu/230W/english/230w5/index.
Safety and Troubleshooting Information • Safety Precautions and Maintenance • Installation Locations • FAQs Safety and Troubleshooting Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Safety and Troubleshooting Information ● ● ● ● ● ● Avoid exposure to heat and extreme cold. Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold. Avoid moving the LCD monitor between locations with large temperature differences. Choose a site that falls within the following temperature and humidity ranges. ❍ Temperature: 0-35°C 32-95°F ❍ Humidity: 20-80% RH Do not subject the LCD monitor to severe vibration or high impact conditions.
About This Manual • About This Guide • Notational Descriptions About This Manual About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other important information. Its contents are identical to the information in our printed version.
About This Manual NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may not be accompanied by an icon.
Product Information • SmartManage • Product Product Information Features • Technical Specifications • Resolution & Product Features Preset Modes • Philips Pixel BRILLIANCE 230W5 Defect Policy • Automatic The Best Productivity Solution Power Saving • Physical ● Outstanding front of screen performance Specification ❍ WUXGA, wide format 1920x1200 resolution for sharper display • Pin ❍ Fast response time capable of handling fast moving pictures ❍ Widest viewing angle up to 176 degree for extra efficiency Assig
Product Information • Vertical refresh rate 56Hz-85Hz • Horizontal Frequency 30kHz-94kHz VIDEO • Video dot rate < 205 MHz (Analog input) < 165 MHz (Digital input) • Input impedance - Video - Sync 75 ohm + 3% 2.2K ohm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polarities Positive and negative • S-Video Y input 1.0Vpp, C input 0.3Vpp, 75ohm input impedance • CVBS Composite, 1.
Product Information * This data is subject to change without notice. RETURN TO TOP OF THE PAGE Resolution and Preset Modes • Recommended 1920 x 1200 at 60Hz 20 factory preset modes: H. freq (kHz) Mode Resolution V. freq (Hz) 31.469 IBM VGA 10H 640x350 70.086 31.469 IBM VGA 3H 720x400 70.086 31.469 IBM VGA 12H 640x480 59.940 35.000 MACINTOSH 640x480 67.000 37.500 VESA 640x480 75.000 35.156 VESA 800x600 56.250 37.879 VESA 800x600 60.317 46.875 VESA 800x600 75.000 49.
Product Information Automatic Power Saving If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
Product Information RETURN TO TOP OF THE PAGE Pin Assignment 1. The digital only connector contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the following table: Pin Signal Assignment No. Pin Signal Assignment No. Pin Signal Assignment No. 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S.
Product Information Pin Assignment No. Pin Assignment No. 1 Red video input 9 +5V 2 Green video input/SOG 10 Cable detect 3 Blue video input 11 Identical output, connected to pin 10 4 Ground 12 Serial data line (SDA) 5 No connect 13 H. Sync / H+V 6 Red video ground 14 V. Sync 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components.
Product Information 2) Swivel RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/product/product.
Installing Your LCD Monitor Installing Your LCD Monitor Front View • Produt Description Setting Up Front View Product Description and • Connecting Your Monitor VESA • Standard Mounting Getting • Started Optimizing • Performance • Universal Card Reader 1 To switch monitor's power On and Off 2 Power LED 3 To access OSD menu 4 To adjust the OSD 5 To adjust brightness of the display 6 To adjust the OSD 7 VOLUME To adjust speaker volume 8 AUTO Automatically adjust the horizontal position, verti
Installing Your LCD Monitor 10 Activate PIP (Picture in Picture) window (230W5VS) or PIP/SIZE adjust screen size (230W5BS) RETURN TO TOP OF THE PAGE Rear View Monitor model (230W5BS) 1 PC audio input for D-Sub 2 PC audio input for DVI-I 3 Earphone jack 4 VGA input 5 DVI-I input 6 USB to USB devices 7 USB to PC host 8 AC power input Video model file:///D|/My%20Documents/dfu/230W/english/230w5/install/install.
Installing Your LCD Monitor 1 Component Video (YPbPr) input 2 Component Video (YPbPr) input 3 Component Video (YPbPr) input 4 CVBS video input 5 S-Video input 6 Audio input for YPbPr video 7 Audio input for CVBS/S-Video 8 PC audio for D-Sub 9 PC audio for DVI-I 10 Earphone jack 11 VGA input 12 DVI-I input 13 USB to USB devices 14 USB to PC host 15 AC power input RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set
Installing Your LCD Monitor Note: You can check the current display settings by pressing the 'OK' button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/install/install.
On-Screen Display On-Screen Display • Description of the OnScreen Display Description of the On Screen Display The OSD • Tree What is the On-Screen Display? This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. file:///D|/My%20Documents/dfu/230W/english/230w5/osd/osddesc.
On-Screen Display file:///D|/My%20Documents/dfu/230W/english/230w5/osd/osddesc.
On-Screen Display file:///D|/My%20Documents/dfu/230W/english/230w5/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/osd/osddesc.
Customer Care & Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • P
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ C Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source. Most Philips monitors offer the possibility of setting the color temperature to any desired value. RETURN TO TOP OF THE PAGE D D-SUB Your monitor comes with a D-Sub cable.
Glossary The DVI interface enables: 1. 2. 3. 4. Reduce signal loss and video noise in signal due to less signal conversion. Independent from display technology, and can be used on LCD, Plasma, LCOS, etc. Plug and play through hot plug detection, EDID and DDC2B. Digital and Analog support in a single connector (DVI-I only).
Glossary U USB or Universal Serial Bus A smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals. USB makes necessary resources available without user intervention. ● ● ● USB eliminates "case anxiety" -- the fear of removing the computer case to install add-on peripherals. USB also eliminates adjustment of complicated IRQ settings when installing new peripherals. USB does away with "port gridlock.
Glossary communication to/from the host. Hub specific status and control commands permit the host to configure a hub and to monitor and control its ports. Device A logical or physical entity that performs a function. The actual entity described depends on the context of the reference. At the lowest level, device may refer to a single hardware component, as in a memory device.
Glossary RETURN TO TOP OF THE PAGE V Vertical refresh rate Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/glossary/glossary.
Download and Print Download and Print •Installing your LCD monitor driver Installing Your LCD monitor driver •Download and System requirements: Printing Instructions ● PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP or later ● Find your driver ".inf/.icm/.cat" at : lcd\pc\drivers Read the "Driver_install02.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print To print the manual: 1. With the manual file open, follow your printer's instructions and print the pages you need. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/download/download.
FAQs (Frequently Asked Questions) • Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information FAQs (Frequently Asked Questions) General FAQs Q: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? A: Recommended video mode is 1920x1200 @60Hz. 1.
FAQs (Frequently Asked Questions) Q: What if I get lost when I am making monitor adjustments? A: Simply press the OSD button, then select 'Reset' to recall all of the original factory settings. Q: What is the Auto function? A: The AUTO adjustment key restores the optimal screen position, phase and clock settings at the press of a single button – without the need to navigate through OSD menus and control keys. Q: My Monitor has no power (Power LED does not light up).
FAQs (Frequently Asked Questions) A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc. Q: Can the Philips LCD Monitor be mounted on the wall or used as a touch panel? A: Yes. Philips LCD monitors have this optional feature. The standard VESA mount holes on the back cover allows the user to mount the Philips monitor on any VESA standard ARM or accessories.
FAQs (Frequently Asked Questions) Q: Are Philips LCD monitors Plug-and-Play? A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000 and the PC98/99 platforms. Q: What is USB (Universal Serial Bus)? A: Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals. USB makes necessary resources available without user intervention. There are three main benefits of USB.
FAQs (Frequently Asked Questions) Q: How are LCDs made? A: LCDs are created from two glass plates separated from each other at a distance of a few microns. The plates are filled with liquid crystal and then sealed together. The top plate is colored with an RGB pattern to make the color filter. Polarizers are then glued to both plates. This combination is sometimes called 'glass' or 'cell.' The LCD cell is assembled into a 'module' by adding the backlight, driver electronics and frame.
FAQs (Frequently Asked Questions) A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized electrons on fluorescent glass. Therefore, CRT monitors basically operate with an analog RGB signal. A TFT LCD monitor is a device that displays an input image by operating a liquid crystal panel. The TFT has a fundamentally different structure than a CRT: Each cell has an active matrix structure and independent active elements.
FAQs (Frequently Asked Questions) Interference, especially magnetic fields. Also, since an LCD display utilizes relatively low power, its power supply is extremely quiet. RETURN TO TOP OF THE PAGE Ergonomics, Ecology and Safety Standards Q: What is the CE mark? A: The CE (Conformité Européenne) mark is required to be displayed on all regulated products offered for sale on the European market. This 'CE' mark means that a product complies with the relevant European Directive.
Troubleshooting Troubleshooting • Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Philips dealer.
Troubleshooting ● ● Display position is incorrect ● Image vibrates on the screen Press the Auto button. Adjust the image position using the Horizontal Position and/or Vertical Position in OSD Main Controls. Check that the signal cable is properly connected to the graphics board or PC. Vertical flicker appears ● ● Press the Auto button. Eliminate the vertical bars using the Clock Adjustment of VIDEO NOISE in OSD Main Controls.
Troubleshooting For further assistance, refer to the Consumer Information Centers list and contact your local Philips distributor. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/safety/saf_troub.
Regulatory Information • TCO'99 Information • TCO'99 Environmental Requirements • TCO'03 Information • Recycling Information for Customers CE Declaration • of Conformity Energy Star • Declaration • Federal Communications Commission (FCC) Notice (U. S.
Regulatory Information • Philips End-ofLife Disposal Information for • UK only • Troubleshooting Other Related • Information • Frequently Asked Questions (FAQs) Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.
Regulatory Information The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma) as a consequence.
Regulatory Information ● ● Energy-saving mode after a certain time-beneficial both for the user and the environment Electrical safety Emissions ● ● Electromagnetic fields Noise emissions Ecology ● ● The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on ❍ chlorinated and brominated flame retardants and polymers ❍ heavy metals such as cadmium, mercury and lead.
Regulatory Information Information Center in each country or the following team of Environmental specialist can help. Mr. Job Chiu - Environment manager Philips Electronics Industries (Taiwan) Ltd, Monitor Business Unit E-mail: job.chiu@philips.com Tel: +886 (0) 3 454 9839 Mr. Maarten ten Houten - Senior Environmental Consultant Philips Consumer Electronics E-mail: marten.ten.houten@philips.com Tel: +31 (0) 40 27 33402 Mr. Delmer F. Teglas Philips Consumer Electronics North America E-mail: butch.
Regulatory Information PHILIPS 230W5 This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software.
Regulatory Information Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Regulatory Information Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Regulatory Information WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A. S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3pin plug fitted in its place.
Regulatory Information terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/safety/regs/regulat.
Other Related Information • Safety and Troubleshooting • FAQs Other Related Information • Troubleshooting Information for Users in the U. S. • Regulatory Information • Information for Users in the U.S • Information for Users Outside the U.S For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
SmartManage • Product Information • Philips Pixel Defect Policy • SmartManage Introduction • SmartManage Features and Benefits • Philips SmartControl • Q&A SmartManage Introduction Philips SmartManage is an advanced solution for users, corporate users in particular, to manage their Philips monitors as part of the asset management environment. The solution includes three essential components, Philips SmartManage Administrator, and Philips SmarControl and Agent.
SmartManage ● ● chipsets that support the DDC/CI interface Microsoft Windows 2000 and XP operation systems. Philips monitors supporting DDC/CI interface 2. Installation How to download "SmartControl Installation " file: 1. 2. 3. 4. 5. 6. Visit http:// www.philips.com/pcstuff Click into "monitors and peripheral" page Select "Manuals/drivers" Enter your model number Select "SmartControl" download SmartControl and its driver for installation.
SmartManage ● ● Product Information Click Product Information in the left pane to view the product information stored in the monitor's memory. General Click on General for general information including driver information, device information, and monitor control. file:///D|/My%20Documents/dfu/230W/english/230w5/product/smart.
SmartManage Within monitor control, users can click on Auto Setup to achieve optimum performance or click on factory reset to reset the parameters of the monitor. Such choices are disabled when using DVI-D (digit) input. Q&A Q1. What is the difference between SmartManage, SmartControl? A.
SmartManage A. It might be your graphic adaptor is not compatible with the SmartControl. If your graphic adaptor is one of the above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl, and re-install it once more. If it is still not working, we are sorry that the graphic adaptor is not supported. Please pay attention to Philips’ web site for any updated SmartControl driver available. Q5.
Philips Pixel Defect Policy • SmartManage • Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips Pixel Defect Policy Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple Three adjacent lit sub pixels - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) (one white pixel) Black Dot Defects appear as pixels or sub pixels that are always dark or 'off'.
Philips Pixel Defect Policy 3 adjacent lit subpixels (one white pixel) 0 Distance between two bright dot defects* 25 mm or more Total bright dot defects of all types 3 or fewer BLACK DOT DEFECTS ACCEPTABLE LEVEL 230W5 MODEL 1 dark subpixel 5 or fewer 2 adjacent dark subpixels 2 or fewer 3 adjacent dark subpixels 1 or fewer Distance between two black dot defects* 15 mm or more Total black dot defects of all types TOTAL DOT DEFECTS 5 or fewer ACCEPTABLE LEVEL 230W5 MODEL Total bright or b
Setting up and Connecting Your Monitor Setting Up and Connecting Your Monitor Your LCD Monitor : • Front View Product Accessory Pack Description • Accessory Unpack all the parts.
Setting up and Connecting Your Monitor Cable Management If you use an Apple MacintoshTM, you need to connect the special Mac adapter to one end of the monitor signal cable. Connect the cables to the back of your computer by following these steps: (a) Turn off your computer and unplug its power cord. (b) Connect the VGA or DVI cable to the video connector. file:///D|/My%20Documents/dfu/230W/english/230w5/install/connect.
Setting up and Connecting Your Monitor (c) Connect the audio cable. (d) Plug the power cord of the computer and the monitor into a nearby outlet. (e) Turn on your computer and monitor. If the monitor displays an image, installation is complete. Connect to DVD/VCR/VCD Connect to DVD/VCR/VCD through component video (YPbPr) Connect to DVD/VCR/VCD through S-VIDEO file:///D|/My%20Documents/dfu/230W/english/230w5/install/connect.
Setting up and Connecting Your Monitor Connect to DVD/VCR/VCD through composite video (CVBS) Connect to Earphone RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/install/connect.
VESA Standard Mounting VESA Standard Mounting Your LCD Monitor : • Front View Product Description • Accessory Pack • Setting up and connecting your monitor • Getting Started • Optimizing Performance • Universal Card Reader 1) Place monitor face down on a safe surface. 2) Remove the cable cover. Remove the base cover. 3) Unscrew the 4 screws at the base. file:///D|/My%20Documents/dfu/230W/english/230w5/install/base.
VESA Standard Mounting 4) VESA mounting holes RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/install/base.
Getting Started Your LCD Monitor : • Front View Product Description • Setting Up and Connecting Your Monitor • Getting Started • Optimizing Performance • Universal Card Reader Getting Started Getting Started Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows® 95/98/2000/Me/XP. This information file ( .
Getting Started 6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button. 7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'. 8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button. 9. Click on the 'OK' button, select your monitor model and click on the 'Next' button. 10.
Getting Started dialog box. If your Windows® 95/98/2000/Me/XP version is different or you need more detailed installation information, please refer to Windows® 95/98/2000/Me/XP user's manual. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230W/english/230w5/install/gt_start.
Universal Card Reader (UCR) Your LCD Monitor : • Front View Product Description • Setting Up and Connecting Your Monitor • Getting Started • Optimizing Performance Universal Card Reader (UCR): • Introduction Installing the Reader Using the • Reader Disconnecting • the Reader Universal Card Reader (UCR) Introduction This 6-in-1 Flash Card Reader & USB Hub combines the functionality of a two-slot memory card reader and a USB hub.
Universal Card Reader (UCR) 1 LED 2 SD/MMC/SM/MS 4-in-1 Socket Supports Secure Digital / MultiMedia / SmartMedia / Memory Stick / Memory Stick Pro cards 3 Dual USB Type A Connectors For connecting USB 2.0 or USB 1.1 devices 4 CF Socket Type I/II Compact Flash Card and IBM Microdrive Rear View 1 USB type A Connector For connecting to USB 2.0 or USB 1.
Universal Card Reader (UCR) RETURN TO TOP OF THE PAGE Installing the Reader For Windows 98SE / Me CAUTION: Make sure you have installed the USB drivers before connecting the reader to the host computer. 1. Insert the Electronic User's Manual CD-ROM into the CD-ROM drive. 2. Double-click the CD-ROM icon in My Computer. Locate and double-click the CD-ROM drive:\lcd \pc\ucr_driver\setup.exe file. 3. Follow the on-screen instructions to complete the software installation. Reboot the computer. 4.
Universal Card Reader (UCR) Using the Reader Identify the Storage Media In Windows, each inserted flash card or USB-connected storage device will be identified as a Removable Drive and assigned with a drive letter in My Computer. You can click on icon representing the drive to gain access to the files contained on your flash cards or USB-connected storage devices. In the Mac OS, each inserted flash card or USB-connected storage device will be represented as a disk icon on the desktop.
Universal Card Reader (UCR) file:///D|/My%20Documents/dfu/230W/english/230w5/install/ucr.
Your Philips F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
Your Philips F1rst Choice Warranty ● ● ● ● Reception problems caused by signal conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the monitor; Product requires modification or adaptation to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country.
Your Philips F1rst Choice Warranty file:///D|/My%20Documents/dfu/230W/english/warranty/war_1st.
Your Guarantee in Central and Eastern Europe Your Guarantee in Central and Eastern Europe Dear Customer, Thank you for purchasing this Philips product, which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts during a period of 36 months from date of purchase.
Your Guarantee in Central and Eastern Europe which apply in countries for which the product was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific country. Just a click away In case of any problems, we advise you to read the operating instructions carefully or go to the www. philips.com/support website for additional support.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee Your Philips F1rst Choice Warranty(Canada/USA) Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
United States Guarantee Your warranty does not cover: ● ● ● ● ● ● ● labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics. reception problems caused by signal conditions or cable or antenna systems outside the unit.
United States Guarantee (877) 835-1838 or (919) 573-7855 (In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty. But, because some states do not allow limitations on how long an implied warranty may last, this limitation may not apply to you.) TO GET WARRANTY SERVICE IN CANADA...
United States Guarantee ● ● ● Other cards installed Having the following information available will also help speed up the process: Your proof of purchase indicating: date of purchase, dealer name, model and product serial number. The full address to which the swap model should be delivered. Just a phone call away Philips’ customer help desks are located worldwide. Within the U.S.
F1rst Choice Contact Information F1rst Choice Contact Information Country Telephone number Tariff Austria 01 546 575 603 Local call tariff Belgium 070 253 010 0.17 Cyprus 800 92256 Free of Charge Denmark 3525 8761 Local call tariff Finland 09 2290 1908 Local call tariff France 08 9165 0006 0.23 Germany 0180 5 007 532 0.12 Greece 00800 3122 1223 Local call tariff Ireland 01 601 1161 Local call tariff Italy 199 404 042 0.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Belarus • Bulgaria • Croatia • Czech Republic • Estonia • Dubai • Hong Kong • Hungary • India • Indonesia • Korea • Latvia • Lithuania • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Romania • Russia • Serbia & Montenegro • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey • Ukraine
Consumer Information Centers ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE-12618 Tallinn Tel: +372 6519900 www.ee.invia.fujitsu.com HUNGARY Serware Szerviz Vizimolnár u. 2-4 HU - 1031 Budapest Tel: +36 1 2426331 Email: inbox@serware.hu www.serware.hu LATVIA ServiceNet LV Jelgavas iela 36 LV - 1055 Riga, Tel: +371 7460399 Email: serviss@servicenet.lv LITHUANIA ServiceNet LT Gaiziunu G. 3 LT - 3009 KAUNAS Tel: +370 7400088 Email: servisas@servicenet.lt www.servicenet.
Consumer Information Centers SLOVAKIA Datalan Servisne Stredisko Puchovska 8 SK - 831 06 Bratislava Tel: +421 2 49207155 Email: servis@datalan.sk SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.Zytnia 1 PL - 05-500 Piaseczno Tel: +48 22 7501766 Email: servmonitor@zolter.com.pl www.zolter.com.pl RUSSIA Tel: +7 095 961-1111 Tel: 8-800-200-0880 Website: www.philips.ru TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.
Consumer Information Centers UKRAINE Comel Shevchenko street 32 UA - 49030 Dnepropetrovsk Tel: +380 562320045 www.csp-comel.com Latin America ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V. Vedia 3892 Capital Federal CP: 1430 Buenos Aires Phone/Fax: (011)-4544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda.
Consumer Information Centers COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information Centre Norte 45 No.669 Col. Industrial Vallejo C.P.02300, -Mexico, D.F. Phone: (05)-3687788 / 9180050462 Fax : (05)-7284272 PARAGUAY Av. Rca. Argentina 1780 c/Alfredo Seiferheld P.O.
Consumer Information Centers URUGUAY Rambla O'Higgins 5303 Montevideo Uruguay Phone: (598) 619 66 66 Fax: (598) 619 77 77 Customer Desk: Phone: 0004054176 VENEZUELA Industrias Venezolanas Philips S.A. Apartado Postal 1167 Caracas 1010-A Phone: (02) 2377575 Fax : (02) 2376420 Canada CANADA Philips Electronics Ltd.
Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA SHANGHAI Rm 1007, Hongyun Building, No. 501 Wuning road, 200063 Shanghai P.R.
Consumer Information Centers INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr. A Besant Road, Worli Bombay 400 025 CALCUTTA Customer Relation Centre 7 justice Chandra Madhab Road Calcutta 700 020 MADRAS Customer Relation Centre 3, Haddows Road Madras 600 006 NEW DELHI Customer Relation Centre 68, Shivaji Marg New Dehli 110 015 INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav.
Consumer Information Centers KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone: 080 600 6600 (toll free) Fax : (02) 709 1210 MALAYSIA After Market Solutions Sdn Bhd, Philips Authorised Service Center, Lot 6, Jalan 225, Section 51A, 46100 Petaling Jaya, Selangor Darul Ehsan, Malaysia.
Consumer Information Centers SINGAPORE Accord Customer Care Solutions Ltd Authorized Philips Service Center Consumer Service 620A Lorong 1 Toa Rayoh Singapore 319762 Tel: +65 6882 3999 Fax: +65 6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 13F, No. 3-1 Yuan Qu St., Nan Gang Dist., Taipei 115, Taiwan Phone: 0800-231-099 Fax : (02)-3789-2641 THAILAND Philips Electronics (Thailand) Ltd.
Consumer Information Centers SOUTH AFRICA PHILIPS SA (PTY) LTD Customer Care Center 195 Main Road Martindale, Johannesburg P.O. box 58088 Newville 2114 Telephone: +27 (0) 11 471 5194 Fax: +27 (0) 11 471 5123 E-mail: phonecare.za@philips.com Middle East DUBAI Philips Middle East B.V. Consumer Information Centre P.O.Box 7785 DUBAI Phone: (04)-335 3666 Fax : (04)-335 3999 file:///D|/My%20Documents/dfu/230W/english/warranty/warcic.
