Register your product and get support at www.philips.com/support 32PFL4907 26PFL4907 22PFL4907 EN User Manual ES Manual del Usuario FR Manuel d’Utilisation EN: F or further assistance, call the customer support service in your country. •• To obtain assistance, contact Philips Customer Care Center; In the U.S.A., Canada, Puerto Rico, or the U.S. Virgin Islands 1 866 309 0843 México D.F.
Contents 1 Notice 5 2 Important 7 7 7 7 Positioning the TV Regulatory notices Environmental care 3 Get started Features Supplied accessories Symbols used in this User Manual Attaching the base Managing cables Installing the remote control batteries Remote control function Control panel Terminals Connecting the antenna or the cable Plugging in the AC power cord Initial setup 4 Use your TV Switching on your TV and putting it in Standby mode Adjusting volume Switching channels Watching channels from a
Return your Product Registration Card or visit at http://www.productrecords.com/philips/ today to get the very most from your purchase. Registering your model with Philips makes you eligible for all of the valuable benefits listed below, so don't miss out. Complete and return your Product Registration Card at once or visit at www.philips.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
1 Notice Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. P&F USA reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this User Manual is believed adequate for the intended use of the system. If the product or its individual modules or procedures are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained.
Copyright All other registered and unregistered trademarks are the property of their respective owners. The terms HDMI and HDMI HighDefinition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. is a trademark of SRS Labs, Inc.
2 Important Environmental care Positioning the TV • • • • • • • • • • • • Large screen TVs are heavy. 2 people are required to carry and handle a large screen TV. Make sure to hold the upper and bottom frames of the unit firmly as illustrated. Install the unit in a horizontal and stable position. Do not install the unit in direct sunlight or in a place subject to dust or strong vibration. Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
3 Get started Features • Supplied accessories User Manual Quick Start guide Quick DTV /TV / CATV Information display • AutoProgram • Net TV • browse the Net TV pages. You can play movies and much more, all from your TV screen. Child lock IMPORTANT Start You can use your remote control to select channels which are broadcast in Digital format and conventional Analog format. Also, cable subscribers can access their cable TV channels.
Attaching the base Managing cables You must attach the base to the unit to have it as a table top unit. Be sure the front and rear of the base match the proper direction. For large screen TVs, at least 2 people are required for these steps. Route your antenna cable and all other cables through the cable management tie at the back of the TV. The holder helps keep your cables tidy and easily manageable. 1 1 1 Attach the cable management tie as illustrated below.
t s r a b c d e f q g h i p j k o n m (POWER-ON / STANDBY-ON) Press to Turn the unit On and go into Standby mode. To completely Turn Off the unit, you must unplug the AC power cord. b ��� FAV Displays a list of all channels marked as favorite. (Includes subchannels) c SLEEP Press to activate the sleep timer. d COLOR buttons (green /yellow) Functionally useful for Net service. e VUDU and COLOR button (blue) Starts up VUDU and functionally useful for Net service.
a VOL ◄/► Touch to adjust volume down (◄) / up (►) or to move left (◄) / right (►) when selecting menu items. b MENU Touch to display the Home menu. c SOURCE Touch to select the connected devices. d CH ▲/▼ Touch to select channels or to move up (▲) / down (▼) when selecting menu items Control panel a g b c d e (POWER-ON / STANDBY-ON) Touch to Turn the unit On and go into Standby mode. To completely Turn Off the unit, you must unplug the AC power cord.
Connecting the antenna or the cable Be sure your antenna or other device is connected properly before plugging in the AC power cord. If you connect to an antenna through RF cable Connecting a set-top box, Blu-ray / DVD recorder via composite connectors and Analog Audio Do not place your recorder too close to the screen because some recorders can be susceptible to signals. Any DTV programs that are broadcasted in your area can be received for free through an antenna connection.
System searching. Please wait... These operations are accessible by remote control. Some may also be accessible by control panel on the main unit. Digital channels found: Analog channels found: Initial setup Auto programming may take more than 20 minutes to complete. Digital channels will take longer than Analog to find and program. Please wait until you see the Auto Programming complete message.
9 Press OK to finish Settings assistant. Store your preferences. Cancel Store • Network updates will appear after Connection test succeeds. Use ◄► to select Yes, then press OK. • When the initial setup is completed, the lowest memorized channel with the confirmation message of the location setting will be displayed on the TV screen. Note •• If you are not receiving a signal from your cable service, contact the Cable provider.
4 Use your TV Switching channels Switching on your TV and putting it in Standby mode To Turn Power On or to Turn Standby On • Touch or press . on the front panel or the remote control. Note •• Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy. Your TV has very low Standby power consumption.
Watching channels from an external device Note Switching Each Input Mode can easily switch with the remote control between TV (DTV or Analog TV) and external devices when they are connected to the unit. 1 Turn On a set-top box or the connected device. • The picture from your set-top box or the connected device might appear automatically on the TV screen. •• After selecting Add new devices, follow the on-screen instructions to select the correct device and connector.
Philips Wireless MediaConnect View photos, play music and watch videos using DLNA You can enjoy your TV as a PC monitor wirelessly using your home network. Make sure you download the Philips Wireless MediaConnect software and install it on your PC before you perform the steps below. On your TV you can play video, music and photo files stored on DLNA certified home media servers connected to your home network. In order to use this feature, you must connect this unit to the Internet.
Guide to DLNA Listen to music using DLNA b a 1 2 c Server 1 Audio Server 2 Photos Server 3 Video d Folder Highway Blues Video10 Blue hills Title: Artist: Album: Duration: 00:05:28 Year: e Press ▲▼ to select a file or a folder. Press OK or Æ∆ to play the selected files. • Press OK or Æ∆ to pause, press OK or Æ∆ again to resume. • Press D to skip up the next file. • Press E to skip down the previous file. • Press C to stop playback.
Net TV My Apps functions Net TV offers Internet services for your TV. Use the remote control to browse the Net TV pages. You can play movies and much more, all from your TV screen. –– Because Net TV is an online system, it can be modified over time to better serve its purpose. –– Some Net TV services can be added, changed or stopped after some time. –– You cannot download and save files or install plug-ins. 1 2 Follow the procedure below before logging in to Net TV.
4 Enjoying vTuner With this unit, you can enjoy video and Internet radio with vTuner via the Internet. In order to watching video and listen to Internet radio, you must connect this unit to the Internet. Video playback After you set up the network connection, follow the procedure below to watch the video. Guide to the player screen e.g.) Recommendations a Recommendations Favo Genr Most b NewsNews Note •• Video service may not be fully available with narrowband Internet connection. (e.g.
Internet radio playback Note After you set up the network connection, follow the procedure below to listen to Internet radio. Guide to the playback screen e.g.) Location a Jazz(3) FM 76.2 FM f e Jazz jAzz jaZz jazZ Genre d Add to favorite list : Jazz Schonan Beach FM 78.9 b Location : Japan Language : Japanese Favorite •• This unit cannot play back stations with audio format other than MP3 and WMA. •• Internet radio service may not be fully available with narrowband Internet connection.
Reset the station list Creating a New Station You can remove all stations / folders in Recently Played, Favorites and My Added Stations. By entering your favorite artists or tracks, Pandora selects music and creates a new station for you on the basis of the entered information. 1 2 3 Follow step 1 in Internet radio playback. ➠ p.21 Use ▲▼ to select Reset, then press OK. Use ◄► to select Yes, then press OK. • All stations / folders in Recently Played, Favorites and My Added Stations are removed.
Using Twitter Guide to Twitter Home screen You can view your Twitter feeds and more using the Twitter application on this unit. –– For more details about Twitter, please visit www.twitter.com Twitter Home Screen consolidates browsing of tweets and some functional menus for Twitter. To call up the screen, press NET TV on the remote control and then use ▲▼◄► to select Twitter. Logging in to Twitter Single View After you set up the network connection, you must log in with your Twitter account.
Viewing Favorites on Twitter Viewing Trends on Twitter Your TV displays the logged in user's favorites on Twitter. Trends show topics trending in your area. 1 Follow steps 1 to 2 in Viewing tweets on the TV. ➠ p.23 2 Use ▲▼ to select Favorite, then press OK. • If you have no favorites, TV was not able to acquire the Tweet. will appear. Displaying Mentions on Twitter Your TV displays replies for the logged in user. 1 Follow steps 1 to 2 in Viewing tweets on the TV. ➠ p.
Using auto mode 1 Switch to one of the channels on a list Press AUTO MODE to set your TV to a predefined picture and sound setting. 1 2 Press OK to display the last list that you selected. Use ▲▼ to select a channel, then press OK. • The TV switches to that channel. Note •• Press CH +/− to select channels in a list or press the NUMBER buttons to select channels that are not in a list. .
For PC Input signal Changing picture format Display modes can be selected when your TV receives a 16:9 or 4:3 video signal. Three types of display modes can be selected for a PC Input signal. Press FORMAT repeatedly to switch the TV aspect ratio. Wide screen 4:3 Unscaled •• This unit can also be connected to your PC that has a DVI terminal. Use an HDMI-DVI conversion cable for this Video connection and it requires Stereo mini 3.5mm plug Audio cable for Analog Audio signal as well.
USB Picture (JPEG) Your TV is fitted with a USB connection that enables you to view photos, listen to music or watch MPEG files stored on a USB Memory Stick. 1 Use ▲▼ to select a file or a folder. avi Image4.jpg 1 Connect the USB Memory Stick to the USB terminal on the side of jpg Image5.jpg mp3 Image6.jpg 2 your TV. Press MENU / EXIT and use ▲▼◄► to select USB, then press OK. Image1.jpg Image7.jpg Image2.jpg Image8.jpg Picture Music Video Image3.jpg avi jpg mp3 Image1.
Music (MP3) Video (MPEG) 1 1 Use ▲▼ to select a file or a folder. avi Track4.mp3 avi Movie4.avi jpg Track5.mp3 jpg Movie5.avi mp3 Track6.mp3 mp3 Movie6.avi Track1.mp3 Track7.mp3 Movie1.avi Movie7.avi Track2.mp3 Track8.mp3 Movie2.avi Movie8.avi Track3.mp3 2 Use ▲▼ to select a file or a folder. Title: Artist: Album: Duration: 00:05:28 Year: Press OK or Æ∆ to play the selected files. • Press OK or Æ∆ to pause, then press OK or Æ∆ again to resume.
5 Use more of your TV This section describes the overview of the Setup menu displayed when you press MENU / EXIT and use ▲▼◄► to select Setup. The Setup menu consists of the function setting items below. 1 Press MENU / EXIT to display Home menu. 3 Use ▲▼ to select the desired menu and an item, then press OK or use ▲▼◄► to determine the setting.
to select the desired setting, then press OK (Color alignment, Noise reduction, Black stretch, * Advanced picture Dynamic contrast, Gamma, MPEG artifact reduction, Color enhancement, Custom color management and Film mode) Picture Before you begin: You must set Home in Location. ➠ p.38 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode. 1 2 Automatic Super zoom 4:3 Press MENU / EXIT and use ▲▼◄► to select Setup, then press OK.
*You can set a particular about picture quality in Advanced picture.
Digital TV operation Sound You can select the Audio language while your TV is receiving the Digital broadcasting. Before you begin: You must set Home in Location. ➠ p.38 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode. 1 2 Press MENU / EXIT and use ▲▼◄► to select Setup, then press OK. Use ▲▼ to select Sound, then press OK.
Digital TV operation Features 1 Press MENU / EXIT and use ▲▼◄► to select Setup, then press 2 In addition to the basic Closed Caption, DTV has its own Closed Caption called Digital caption service. Use this menu to change the settings for Digital caption service. OK. Use ▲▼ to select Features, then press OK.
Note •• Digital caption service that you can switch differs depending on the broadcast description. •• Closed Captioning service may not be controlled by this unit’s menu options if you are watching television through an external cable or satellite set-top box. In which case you will need to use the menu options on the external set-top box to control Closed Captioning. •• The captions do not always use correct spelling and grammar.
US movie ratings Channel lock Particular channels or external Input modes can be invisible in this function. 3 4 Use ▲▼ to select Channel lock, then press OK. Use ▲▼ to select the particular channels or external Input, then press OK repeatedly to switch between view and block. • indicates that the channel or Input Source is locked. • indicates that the channel or Input Source is not locked.
Canada English or Canada French ratings You can select the rating for Canada English or Canada French broadcasting. 3 4 Use ▲▼ to select Canada English ratings lock or Canada French ratings lock, then press OK. Use ▲▼ to select the desired rating, then press OK repeatedly to switch between view and block. • indicates that the rating is locked. • indicates that the rating is not locked.
Channel installation Weak channel installation Be sure the RF cable is correctly connected to this unit and you are registered with your cable TV provider when you install cable channels. This function lets you add the channels that were not added by the AutoProgram due to the reception conditions during the initial setup. It is available only when you select Antenna in Installation mode. Autoprogram 1 Use ▲▼ to select Channels, then press OK.
Preferences Use Philips EasyLink You can set the unit to reduce the power consumption or adjust the backlight brightness in Location setting. EasyLink allows you to operate your connected EasyLink device. Your TV supports Philips EasyLink, which enables one-touch play and one-touch Standby between EasyLink-compliant devices. Compliant devices must be connected via an HDMI connector. Setting your location to home One-touch play Use ▲▼ to select Preferences, then press OK.
EasyLink Device list This function allows you to operate the linked functions between our brand devices with a EasyLink feature and this unit connecting through an HDMI cable. You must connect this unit to our brand EasyLink devices and be sure its EasyLink setting is also set to On. 1 2 3 Use ▲▼ to select Preferences, then press OK. Use ▲▼ to select EasyLink, then press OK. Use ▲▼◄► to select the item you want to adjust, then press OK.
Wireless setting Network Set up network connection settings in order to use Net TV or network upgrade function. • • Select to use a wireless LAN to connect to the Internet by wireless connection. 4 The meanings of abbreviations are defined as below. AP : Wireless LAN Access Point WPS : Wi-Fi protected Setup SSID : Wireless network name The key entry screen will appear when you select SSID, WEP /WPA or Proxy address. Use ▲▼ to select Wireless, then press OK.
Wireless network setting This menu is displayed only when you set Wireless in Network selection. In order to use a wireless network, you must set up a connection to the AP (e.g. wireless router). 3 Use ▲▼ to select Wireless network setting, then press OK. Auto Search for wireless networks automatically and select the SSID from the list. 4 5 Use ▲▼ to select Auto, then press OK. The list of wireless networks will be displayed. Use ▲▼ to select the appropriate the SSID, then press OK.
IP configuration In following cases, select IP configuration to set each setting as necessary. –– When connection test failed with the setting of Connection test. –– When instructed by your Internet service provider to make specific settings in accordance with your network environment. 3 4 Proxy configuration 3 4 Use ▲▼ to select a setting, then press OK. Network selection Proxy setting Use ▲▼ to select IP configuration, then press OK.
Setting status You can check the status of network settings. 2 Use ▲▼ to select Setting status, then press OK. • Network setting list will be displayed. • MAC address of this unit will be displayed in the list. Checking your current software version 1 Use ▲▼ to select Software information, then press OK. • The version and a description of the current software is displayed. Picture Software information Reset network settings Sound Software update You can reset the status of network settings.
Upgrading the software 7 USB upgrade Note You can upgrade the software by using USB Memory Stick. 1 Connect your USB Memory Stick with the upgrade file to the USB terminal on the side of your TV. Press again to Turn the unit On. • The TV starts up with the new software. For further assistance, please contact Call Center. • In order to update software via the Internet, you must connect the unit to the Internet and set up necessary settings. Network settings assistant ➠ p.40 Network ➠ p.
6 Connecting devices No supplied cables are used with these connections: •• Please purchase the necessary cables at your local store. Before you connect AC power cord: Be sure other devices are connected properly before plugging in the AC power cord. Connecting your devices HDMI Digital connection �������������������������������������������������� connection offers the highest picture quality.
HDMI-ARC connection Composite Analog Video Connection HDMI-ARC allows you to use EasyLink to output TV Audio directly to a connected Audio device, without the need for an additional Digital Audio cable. Composite Analog Video connection offers standard picture quality for video devices connected to the unit. If you connect to the unit’s Composite Video (Y/VIDEO) Input jack, connect Audio cables to the Audio (L/R) Input jacks. When the Audio is monaural, then only connect to the Audio L Input jack.
Connecting the TV to the Internet using a wireless LAN PC connection HDMI connection Broadband router This unit can be connected to your PC that has a HDMI terminal. Use an HDMI cable for this Digital connection. WLAN USB wireless LAN adapter Ethernet cable Internet IN LAN OUT HDMI cable PC Network provisioning equipment Note •• After you made the wireless connection, set up necessary network settings. Network ➠ p.40 •• Use a Wireless LAN Access Point (AP) (e.g.
The following video signals can be displayed: Format Resolution VGA 640 x 480 SVGA 800 x 600 XGA 1,024 x 768 1,280 x 768 1,360 x 768 WXGA Refresh rate 60Hz Other formats or non-standard signals will not be displayed correctly. Note •• Please purchase the VGA cable or HDMI-DVI conversion cable that has a ferrite core. •• The following operations may reduce noise. –– Attach a ferrite core to the AC power cord of your PC.
7 Useful tips FAQ Question Answer My remote control does not work. What should I do? •• Check the antenna or cable connection to the main unit. •• Check the batteries of the remote control. •• Check if there is an obstacle between the infrared sensor window and the remote control. •• Test the signal Output use IR Signal Check. ➠ p.52 If okay, then possible infrared sensor trouble. •• Aim the remote control directly at the infrared sensor window on the front of the unit.
Symptom Remedy Power is ON but no screen image. •• Check whether the connection of the antenna, cable receiver or satellite box is connected correctly. •• Check whether all the cables to the unit are connected to the correct Output jack of your device like Blu-ray / DVD recorder. •• Make sure that the selected Input mode is connected to the working Input jack. •• Check if your computer is NOT in sleep mode when the Input mode of this unit is in PC mode.
Symptom Remedy Wireless LAN connection fails or wireless connection is poor. •• Check the installation location of the TV and wireless router (access point). Signal quality may be affected for the following reasons. Cannot use the wireless connection. •• Check if the Wireless LAN Access Point (AP) (e.g. wireless router) is oriented properly or not placed too close between them.
8 Information Glossary Maintenance Cabinet Cleaning DTV (ATSC) Acronym that stands for Advanced Television Systems Committee and the name of the Digital broadcasting standards. • Aspect ratio • The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the TV screen is almost square); widescreen models are 16:9 (the TV screen is almost twice as wide as its height).
9 Specifications Model # 32PFL4907 26PFL4907 22PFL4907 Picture enhancement Type WXGA (1366 x 768 pixels 60Hz) Aspect ratio 16:9 Viewing angles 178° (V) by 178° (H) 150° (V) by 160° (H) Built-in Digital tuner 160° (V) by 170° (H) ATSC / NTSC Sound enhancement Mono / Stereo Mono, Stereo, SRS TruSurround XT® Power output (RMS watts) 8W x 2 2W x 2 Equalizer 5 band Ease of use SD (4:3 Source) Picture format HD (16:9 Source) HDMI AV (4:3 Source) HDMI AV (16:9 Source) PC Source : A
10 Warranty LIMITED WARRANTY ONE (1) YEAR WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
i License This product uses some open source software: GPL software:linux, gcc, sysfsutils, Realtek WiFi driver, binutils, busybox, dhcpcd LGPL software: directfb, glibc, Qt MIT: Expat, c-ares, libxml2, lua, lua-xmlreader, lua-slncrypto, giflib MIT/X: cURL gSOAP Public License: gSOAP BSD: WPA Supplicant zlib/libpng License: zlib, libpng XML-RPC FOR C/C++ license: xmlrpc Free Type, LibJPEG, OpenSSL, MINIX 3, unicode, ADPCM, OpenGL GPL GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991
ii 3. 4. 5. 6. 7.
iii OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
iv its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries.
v 4. 5. 6. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
vi subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11.
vii MIT Expat Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers. c-ares Copyright 1998, 2009 by the Massachusetts Institute of Technology.
viii BSD Copyright (c) 2003-2010, Jouni Malinen and contributors All Rights Reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
ix 5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www. openssl.
x 7. Modification is not permitted with respect to this document. All copies of this document must be verbatim. EXHIBIT 1 UNICODE, INC. LICENSE AGREEMENT - DATA FILES AND SOFTWARE Unicode Data Files include all data files under the directories http://www.unicode.org/Public/, http://www.unicode.org/reports/, and http://www.unicode.org/cldr/data/. Unicode Data Files do not include PDF online code charts under the directory http://www.unicode.org/Public/.
xi 1.7. “Licensed Patents” means patent claims Licensable by SGI that are infringed by the use or sale of Original Code or any Modifications provided by SGI, or any combination thereof. 1.8. “Modifications” means any addition to or deletion from the substance or structure of the Original Code or any previous Modifications. When Covered Code is released as a series of files, a Modification is: A.
xii 7. 8. 9. 10. 11. 12. 13. implied or statutory, to which, under any applicable law, it might be deemed to have been subject. Claims of Infringement. If Recipient learns of any third party claim that any disposition of Covered Code and/or functionality wholly or partially infringes the third party’s intellectual property rights, Recipient will promptly notify SGI of such claim. Versions of the License.
P&F USA, Inc. PO Box 2248, Alpharetta, GA 30023-2248 P&F Mexicana, S.A. de C.V. Av. La Palma No. 6, Col. San Fernando La Herradura, Huixquilucan Edo. de México C.P. 52787 Philips and Philips Shield are used under license of Koninklijke Philips Electronics N.V.