Groomer Instruction Manual

60-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Norelco Groomer,
send the product back and we’ll refund you the full purchase
price.
The Groomer must be shipped prepaid by insured
mail, insurance prepaid, and have the sales receipt,
indicating purchase price and the date of purchase,
enclosed.The Groomer must be postmarked no later
than 60 days after the date of purchase. Norelco
reserves the right to verify the purchase price of the
Groomer and limit refunds not to exceed suggested
retail price.
Send dated sales receipt, your complete name and address
as indicated below, and the Groomer, prepaid to:
Norelco Consumer Products Company
A Division of Philips Electronics
North America Corporation
450 North Medinah Road, Dock 16
Roselle, IL 60172-2329
Please allow 4-6 weeks for delivery of check.
(Please Print)
Name __________________________________
Address_________________________________
City____________________________________
State__________________Zip______________
Daytime Telephone No. (_____)______________
E-mail Address: ___________________________
REASON FOR RETURNING: _______________
_______________________________________
_______________________________________
_______________________________________
hear a click.
◗ Hold the Groomer upright when you use the
smaller neckline and sideburn trimmer attachment
(fig. 12).
Using Nose, Ear & Eyebrow
Attachment
Be certain the Groomer is in the OFF position.
To attach or remove nose, ear, eyebrow
attachment (or change attachments):
◗ Remove the Accu•Control comb attachment (fig.
9).
◗ Remove the full width trimmer attachment by
pushing the release button (fig. 10).
◗ Put the nose, ear, eyebrow attachment on the
Groomer (fig. 13). You will hear a click.
Trimming Nose Hair
◗ Make sure nasal passages are clean.
Place nose, ear and eyebrow attachment on
Groomer.
Switch the Groomer on and insert the tip of
the attachment into one nostil (fig. 14).
C
AUTION: Do Not insert the tip more
than 3/16 in./5mm into your nostril.
Slowly move the tip in and out while turning it
around at the same time in order to remove
unwanted hair. For best results, make sure the
side of the tip is firm against skin. This will
reduce the tickling effect that can occur
during trimming of nose hair.
Turn off Groomer. Wipe attachment clean
after each use.
Trimming Ear Hair
◗ Clean outer area of ear and ear canal. Make sure
it is free of wax.
◗ Nose, ear and eyebrow attachment should be on
the Groomer.
Switch the Groomer on and move the tip softly
around the edge of ear to remove hairs
extending beyond the outer ear (fig. 15).
Carefully insert the tip into outer ear canal.
C
AUTION: Do not insert the tip further
than 3/16 in./5mm into the ear as this could
cause damage to the eardrum (fig. 16).
Turn off Groomer. Wipe attachment clean
after each use.
Trimming Eyebrow
◗ Nose, ear and eyebrow attachment should be on
Groomer.
Switch the Groomer on and use the tip to
cut individual eyebrow hairs.
The Groomer can be used for clipping single long
hairs.
Put the Groomer at the root of the hair and
move it along the edge of the eyebrow from
the base of the nose towards the outer tip of
the eyebrow in the direction of hair growth
(fig. 17).
I
MPORTANT: Do not use the Groomer to define
or t
ri
m th
e entire eyebrow. Do not try to trim your
eyelashes. Be careful not to get too close to your
eyelashes and eyes!
Turn off Groomer. Wipe attachment clean
after each use.
Hair Clipping
Make sure that the appliance is fully charged before
you start clipping hair. The appliance will not
operate while cord is connected to electrical outlet.
◗ Before you start clipping, make sure that the head
of the person whose hair you are cutting is at the
same level as your chest so that all parts of his/her
head are clearly visible and within easy reach.
◗ Only use the appliance on dry hair.
◗ Do not use on freshly washed hair
◗ Before you begin, comb the hair in the direction of
growth.
◗ To achieve optimal clipping results, always move
the appliance slowly through the hair against the
direction of hair growth.
Clipping with hair comb attachment
Put the hair clipper comb on the full width
trimmer attachment and push until you
hear it ‘click’ into place (fig. 18).
Press the Hair Length Selector and slide it
to the desired setting. See Table 2.
The setting selected will appear in the
window to the left of the Hair Length
3
2
1
3
2
1
3
2
1
4
3
2
1
2
1
Trimming your Beard & Moustache
with Accu•Control Guide Comb
Attachment
◗ Use this Groomer for its intended household use
as described in this manual.
◗ Make sure that the Groomer is fully charged
before you star t trimming. This Groomer will not
operate while cord is connected to electrical outlet.
Put the Accu•Control comb on the full width
trimmer attachment until you hear it click into
place (fig. 6). The Accu•Control comb will
not work with the smaller neckline and
sideburn trimmer attachment.
Press the Hair Length Selector and slide it to
the desired trimming length setting. The
selected setting number will appear in the
window to the left of the Hair Length
Selector (fig.7). See Table 1 for settings.
◗ If you are trimming for the first time, start by using
the Accu•Control comb at the maximum
trimming length setting (#9) to prevent accidentally
trimming hairs too short. As you become familiar
with the settings, adjust Hair Length Selector to
desired trimming length. Selector will "click" into
position at each setting.
Switch the Groomer ON.
To trim in the most effective way, move the
Groomer against the direction of hair growth.
Make sure the surface of the Guide Comb
always stays in contact with the skin (fig. 8).
N
OTE: S
inc
e all ha
irs d
o not g
row in the same
direction, you may want to try different trimming
d
ire
ctio
ns (i.e., upwards, downwards, or across).
P
ract
ice i
s best f
or op
timum results.
If a lot of hair has accumulated in the Guide Comb,
remove the comb and blow and/or shake the hair out
of the comb. You can also use the cleaning brush
provided to remove hair from the comb area.
◗ REMEMBER: You must reset the hair length
selector back to your desired setting every time
you replace the guide comb on the appliance.
The remaining hair length corresponds with the
smallest distance between the cutting blade and the
spot where the comb is in contact with the skin.
◗ Cutting without the comb attachment or setting
the Accu•Control guide comb to #1 position will
result in a stubble beard look.
Beard Trimming Without
Accu•Control Guide Comb
Remove Accu•Control guide comb if you are:
◗ Defining hair lines
◗ Trimming nape of neck
◗ Removing single, unwanted hairs
Be certain the Groomer is in the OFF position.
Remove the Accu•Control comb attachment by
pressing and sliding the Hair Length Selector
upwards (fig. 9).
Never pull off the Accu•Control comb attachment by
grasping the flexible top portion. Always pull off by the
bottom part of attachment.
Switch the Groomer on.
Make well-controlled movements. Touch the
hair/skin lightly with the Groomer.
Defining Beard, Moustache and
Sideburns
Sideburn
Be certain the Groomer is in the OFF position.
Remove the Accu•Control comb attachment by
pressing and sliding the Hair Length Selector
upwards (fig. 9).
Detach the full width trimmer attachment by
pushing the release button (fig. 10).
Put the smaller neckline and sideburn trimmer
attachment on the Groomer (fig. 11). You will
4
3
2
1
4
3
2
1
4
3
2
1
Selector (fig. 19).
When you are clipping for the first time, start at
the maximum clipping length setting (#9) to
familiarize yourself with the appliance and
prevent accidentally trimming hairs too short. As
you become familiar with the settings, adjust the
Hair Length Selector to desired trimming length.
Selector will ‘click’ into position at each setting.
Make sure that the flat part of the comb is
always in full contact with the scalp to
obtain an even result (fig. 20-21).
Move the appliance slowly over the crown
from different directions to achieve an even
result (fig. 22).
Always move the appliance against the
direction of hair growth.
Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
Turn the Groomer off and remove the hair
comb often to blow and/or shake out hair
that has accumulated.
◗ REMEMBER: You must reset the hair length
selector back to your desired setting every time
you replace the hair clipping comb on the
appliance.
Contouring without the hair clipping
comb attachment
Remove the hair comb by pressing and sliding
the Hair Length Selector upwards (fig. 23).
Be careful when you are clipping without comb
attachment as when the appliance is turned on it
will trim every hair it touches.
Tilt the appliance in such a way that only one
edge of the trimming attachment touches the
hair ends when you shape the contours
around the ears (fig. 24).
To contour the nape of the neck or hairline,
turn the appliance and hold it with the
trimming attachment pointing downwards
(fig. 25).
To contour the sideburns, turn the appliance
and hold it with the trimming attachment
pointing downwards (fig. 26).
Cleaning
◗ Do not use water or a moist cloth to clean the
Groomer.
◗ Always switch Groomer OFF before cleaning.
◗ Do not use abrasive, scourers or liquids such as
alcohol, benzene, bleach or acetone to clean the
Groomer.
◗ Never clean, replace or remove Groomer
attachments with motor ON.
◗ Do not apply pressure to cutters.
◗ Do not touch cutters with hard objects as this
may damage them.
◗ Do not use while bathing, showering or immerse
the Groomer in water or other liquids as damage
to Groomer may occur.
During Use:
◗ If cut hairs have accumulated in the Guide Comb
area, remove hairs by shaking, blowing or using
cleaning brush provided. Remember to adjust the
trimming length back to your selected setting
when you replace the guide comb on Groomer.
Once a Week:
Make sure the Groomer is switched OFF and
disconnected from the electrical outlet.
Remove any attachments.
Blow and/or shake out any hair that may have
accumulated in the attachment.
Clean the outside and inside of the
attachment with the brush supplied (fig. 27).
The cutter is fixed to the trimming
attachment(s) and cannot be removed.
4
3
2
1
4
3
2
1
8
7
6
5
4
4203 000 53671
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
the following:
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a Groomer that has fallen
into water. Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store Groomer where it can
fall or be pulled into a tub or sink. Do not
place in or drop into water or other liquid.
4. Always unplug this Groomer from the
electrical outlet immediately after using, except
when Groomer is (re)charging.
5. Unplug Groomer before cleaning.
6. When discarding Groomer, unplug Groomer
to remove rechargeable battery. See Battery
Removal instruction sheet.
WAR NIN G
To reduce the risk of burns, fire, electric
shock or injury to persons:
1. Close supervision is necessary when
this appliance is used by, on, or near children
or invalids.
2. Use this Groomer for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this Groomer if it has a dam-
aged cord or plug, if it is not working properly,
if it has been dropped, damaged, or dropped
into water. Return the Groomer to an
Authorized Norelco Service Location for
examination and repair.
4. Keep the Groomer, cord and any attachments
away from heated surfaces.
5. Never drop or insert any object into any
opening.
6. Do not operate, charge or plug in Groomer
outdoors or where aerosol (spray) products
are being used or where oxygen is being
administered.
7. Do not use this Groomer with a damaged or
broken cutter, or cutting unit as injury may
occur.
8. Always attach plug to Groomer first, then to
outlet. To disconnect, turn ON/OFF switch to
“OFF” position (switch is down), then remove
plug from outlet.
9. To prevent possible damage to the cord, do
not wrap cord around the Groomer.
10. Never put Groomer in direct sunlight or store
at a temperature above 140°F.
11. This Groomer is for use on human facial hair
only. Do not use this Groomer for any other
purpose.
12. Always store your Groomer, attachments and
power plug in a moisture-free area. Make sure
the cord is disconnected from the Groomer.
SAVE THESE
INSTRUCTIONS
IMPORTANT: YOUR GROOMER
CONTAINS A NICKEL-CADMIUM
RECHARGEABLE BATTERY. See Battery
Removal instruction sheet.
IMPORTANT: The power plug contains a
transformer. Do not cut off the power plug
to replace it with another plug as this will
cause a hazardous condition.
To Charge/Recharge
◗ Fully charge Groomer before using for the first
time or after non-use for a long period of time.
◗ Battery performance is best if you recharge only
when the battery is (almost) completely empty.
◗ Charging or recharging at temperatures below
40˚F or higher than 95˚F adversely affects lifespan
of the battery.
◗ Continuously recharging Groomer will reduce
lifespan of battery.
Be certain Groomer is OFF.
2. You may charge the Groomer:
◗ In the charging stand by inser ting the plug into the
socket located in the bottom of the charging stand
(fig. 2). Place the Groomer directly on the
charging pin in the stand (fig. 3).
◗ By inserting the charging plug directly into the
Groomer (fig. 4).
Plug charging plug into any 120V AC outlet.
Use only the cord provided.
After a few moments, the green Charging
Indicator Light on the power plug will light
to indicate the Groomer is charging (fig. 5).
◗ It will take approximately 10 hours to fully charge
the Groomer for a cordless trimming time of up
to 35 minutes.
◗ Disconnect the cord and unplug from electrical
outlet.
Optimize the working life
of the battery
◗ After the Groomer has been charged for the first
time, do not recharge the Groomer between
trimming sessions. Continue using it until the
battery is completely empty.
◗ Do not charge for more than 24 hours.
◗ Do not keep cord permanently plugged in.
◗ Discharge/run down the battery completely twice
a year by letting the motor run until it stops.
◗ If the Groomer hasn’t been used for a long period
of time, it must be recharged for a full 10 hours.
Cordless Trimming
Charge according to directions. Unplug
Personal Groomer from outlet.
Slide ON/OFF switch ON to begin trimming.
If the battery is empty and you want to trim
your beard, charge the Groomer for at least 3
hours and you will have enough power for
one use (10 minutes).
Put It To The Test
Like many new products, your Norelco MultiTrim
Personal Groomer may take a little getting used to. If
you are using an electric Personal Groomer for the
first time, or if you’ve been using a different brand,
take the time to acquaint yourself with your new
Personal Groomer.
Your Personal Groomer features the unique
Accu•Control System combined with adjustable
Length Settings to make trimming facial hairs
or hair clipping goof proof.
Throw your scissors away and put your new
Personal Groomer to the test. We guarantee
precise, professional results or Norelco will refund
you the full purchase price.
Accu•Control System
The unique Norelco Accu•Control System puts you
in complete control while trimming your facial hairs
with no prior experience needed. The f lexing Guide
Comb adjusts automatically to hug the contours of
your face for a trim that is both even and accurate.
And, it’s easy to maneuver over those hard-to-reach
areas such as the throat and chin. The Hair Length
Selector allows you to choose among 9 preset hair
lengths and clicks into position so you can control
the exact hair length you desire or vary the length of
your facial hair.
The Hair Clipping Comb also features 9 preset hair
lengths and clicks into position so you can control
the exact hair length you desire. The Norelco
Personal Groomer for professional, goof-proof results
every time or your money back.
Tr i m m i n g
◗ Make sure hair is clean and dry.
◗ Always comb the hair with the styling comb in
the direction of growth before you start trimming.
D
o not move the Groomer too fast. Make smooth
and gentle movements.
3
2
1
4
3
2
1
Place the attachment back on Groomer or
place in the storage stand (fig. 28).
This Groomer has no other user-serviceable
parts. Any other service should be performed by
an Authorized Norelco Service Location.
Storage
◗ Be sure Groomer is turned OFF. Remove cord
from outlet and Groomer before storing in a safe,
dry location where it will not be crushed, banged,
or subject to damage.
◗ Store the Groomer and attachments in the
storage stand to prevent damage.
◗ Do not wrap cord around Groomer or stand
when storing.
◗ Store cord in a safe location where it will not be
cut or damaged.
◗ Do not place or store Groomer where it can fall
or be pulled into a tub or sink, water or other
liquid while plugged in.
Replacing The Cutting Unit
If your cutters become damaged or worn, do not
continue using the Groomer. Cutters should be
r
eplaced immediately by an Authorized Norelco
Service Location.
Assistance
For assistance or the Authorized Norelco Service
Location nearest you, call toll free:
1-800-243-3050
or visit our website: www.norelco.com
Authorized Norelco Service Location information is
available 24 hours a day, 7 days a week.
Battery Removal
◗ This Norelco Groomer contains a rechargeable
Nickel-Cadmium battery, which must be disposed
of properly.
◗ Battery should only be removed when Groomer
is to be discarded.
◗ Refer to Battery Removal instruction sheet for
directions on removing the rechargeable battery.
5
A. Neckline & Sideburn Trimmer Attachment
B. Full Width Trimmer Attachment
C. Lifetime Self-Sharpening 3-Dimensional Rounded
Stainless Steel Cutter Blades
D. Accu•Control Beard & Moustache Trimmer
Guide Comb
E. Hair Clipping Comb
F. 9 Position Hair Length Selector
G. Release Button
H. On/Off Slide Switch
I. Socket for appliance plug
J. Cleaning Brush
K. Styling Comb
L. LED Charging Indicator Light on Adaptor
M. Appliance Plug
N. Charging Plug
O. Nose, Ear, Eyebrow Trimmer Attachment
P. Charging/Storage Stand
Norelco
D
C
B
G
H
J
K
N
M
O
P
A
E
F
L
I
Features
Remaining hair length
(mm)
4
6
8
10
12
14
16
18
20
Setting
1
2
3
4
5
6
7
8
9
Table 2. Hair clipper
Remaining hair length
(mm)
2
4
6
8
10
12
14
16
18
Setting
1Stubble
2 Closely Cropped
3 Shor t
4 Medium Short
5Medium
6Medium Long
7Long
8Extra Long
9Longest
Table 1. Beard trimmer
2 3 4
5 6 7
8 9 10
11 12 13
MAX 0.5cm
14 15
MAX 0.5cm
16
17 18 19
20 21 22
23 24 25
26 27 28
fig. 1
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new Norelco
product, Model G270, against defects in materials or workmanship for a
period of two years (cutters for up to five years) from the date of purchase,
and agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident,
misuse or abuse, lack of reasonable care, the affixing of any attachment not
provided with the product or loss of parts or subjecting the product to any
but the specific voltage.* Use of unauthorized replacement parts will void
this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY
FOR WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE AND WILL NOT REIMBURSE THE CONSUMER FOR
DAMAGE RESULTING FROM WARRANTY SERVICE PERFORMED BY A
NON-AUTHORIZED REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply take or ship the product postage
prepaid to the nearest Authorized Norelco Service Location. It is suggested
that for your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized by
Philips Electronics North America Corporation. This warranty gives you spe-
cific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above exclusion and limitations may not
apply to you.
*Read enclosed instructions carefully.
Manufactured for: Norelco Consumer Products Company
A Division of Philips Electronics North America Corporation
1010 Washington Blvd., Stamford, CT 06912-0015
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
MultiTrim, All-In-One and ACCU•CONTROL are Trademarks of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.
© 2004 Philips Electronics North America Corporation. All Rights Reserved.
ULTRA PRECISE, ULTRA CONVENIENT...GUARANTEED!
420300053671.qxd 11/19/03 6:22 PM Page 1 (Black plate)