GC4800 series User manual
1
GC4800 series ENGLISH 6 BAHASA MELAYU 27 繁體中文 45 简体中文 60
ENGLISH Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. General description (Fig.
Important ENGLISH 7 Read this user manual carefully before you use the appliance and save it for future reference. Danger -- Never immerse the iron in water. Warning -- Check if the voltage indicated on the type plate corresponds to the local mains voltage before you connect the appliance. -- Do not use the appliance if the plug, the mains cord or the appliance itself shows visible damage, or if the appliance has been dropped or leaks.
ENGLISH -- Children should be supervised to ensure that they do not play with the appliance. -- Do not let the mains cord come into contact with the hot soleplate of the iron. Caution -- Only connect the appliance to an earthed wall socket. -- Check the mains cord regularly for possible damage. -- The soleplate of the iron can become extremely hot and may cause burns if touched.
ENGLISH 9 (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. Before first use 1 Remove any sticker, protective foil or plastic from the soleplate. 2 Rinse and dry the filling cup. Preparing for use Filling the water tank Type of water to be used You can use normal tap water to fill the water tank.
ENGLISH Do not fill the water tank beyond the MAX indication. Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank. 5 Close the cap of the filling opening (‘click’). Selecting the temperature and steam setting Temperature and steam settings Fabric type Temperature setting Steam setting Steam boost Ionic DeepSteam (specific types only) Linen MAX 5-6 \ yes Cotton 3 3-4 \ yes Wool 2 1-2 N.A. yes Silk 1 0 N.A. N.A.
ENGLISH 11 1 Specific types only: remove the heatresistant protective cover. Do not leave the heat-resistant protective cover on the soleplate during ironing. 2 Put the iron on its heel. 3 To set the required ironing temperature, turn the temperature dial to the appropriate position (see the ‘Temperature and steam settings’ table above). Check the laundry care label for the fabric type.
ENGLISH 5 Put the mains plug in an earthed wall socket. ,,The amber temperature light goes on. 6 When the amber temperature light has gone out, wait a while before you start ironing. ,,The temperature light goes on from time to time during ironing. Using the appliance Note:The iron may give off some smoke when you use it for the first time.This ceases after a short while. Ironing without steam 1 Set the steam control to position 0 (= no steam).
ENGLISH 13 Steam ironing 1 Make sure that there is water in the water tank. 2 Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Selecting the temperature and steam setting’). 3 Set the appropriate steam setting (see chapter ‘Preparing for use’, section ‘Selecting the temperature and steam setting’). Note:The iron starts to produce steam as soon as it reaches the set temperature.
ENGLISH 1 Make sure that there is water in the water tank. 2 Set the required ironing temperature (see chapter ‘Preparing for use’, section ‘Selecting the temperature and steam setting’). 3 Set the appropriate steam setting (see chapter ‘Preparing for use’, section ‘Selecting the temperature and steam setting’). 4 Press the Ionic DeepSteam button once to switch on the Ionic DeepSteam function. ,,The blue Ionic DeepSteam light goes on and you hear a humming sound.
ENGLISH 15 5 Press the Ionic DeepSteam button again to switch off the Ionic DeepSteam function. Note:The Ionic DeepSteam function is only effective when it is used in combination with a steam setting and a temperature setting between 2 and MAX. Note: Do not use the Ionic DeepSteam function when you iron without steam and/or at low temperature settings. However, ironing at low temperatures without steam with the Ionic DeepSteam function switched on will not damage the iron.
ENGLISH Steam boost function A steam boost from the special Steam Tip soleplate helps remove stubborn creases. The steam boost enhances the distribution of steam into every part of your garment. The steam boost function can only be used at temperature settings between 3 and MAX. 1 Press and release the steam boost button. Vertical steam boost 1 You can also use the steam boost function when you hold the iron in vertical position. This is useful for removing creases from hanging clothes, curtains etc.
ENGLISH 17 Automatic shut-off function (specific types only) The automatic shut-off function automatically switches off the iron if it has not been moved for a while. ,,The red auto-off light flashes to indicate that the iron has been switched off by the automatic shut-off function. To let the iron heat up again: 1 Pick up the iron or move it slightly. ,,The red auto-off light goes out.
ENGLISH Cleaning and maintenance Cleaning 1 Set the steam control to position 0, remove the plug from the wall socket and let the iron cool down. 2 Wipe flakes and any other deposits off the soleplate with a damp cloth and a non-abrasive (liquid) cleaning agent. To keep the soleplate smooth, avoid hard contact with metal objects. Never use a scouring pad, vinegar or other chemicals to clean the soleplate. 3 Clean the upper part of the iron with a damp cloth. 4 Regularly rinse the water tank with water.
ENGLISH 19 Using the Calc-Clean function Use the Calc-Clean function once every two weeks. If the water in your area is very hard (i.e. when flakes come out of the soleplate during ironing), use the CalcClean function more frequently. 1 Make sure the appliance is unplugged. 2 Set the steam control to position 0. 3 Fill the water tank to the MAX level. Do not put vinegar or other descaling agents in the water tank. 4 Set the temperature dial to MAX. 5 Put the plug in an earthed wall socket.
ENGLISH After the Calc-Clean process 1 Put the plug back into the wall socket and let the iron heat up to let the soleplate dry. 2 Unplug the iron when it has reached the set ironing temperature. 3 Move the hot iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate. 4 Let the iron cool down before you store it. Storage 1 Set the steam control to position 0 and unplug the iron. 2 Empty the water tank. 3 Let the iron cool down in a safe place.
ENGLISH 21 Heat-resistant protective cover (specific types only) You can store the iron on the heatresistant protective cover immediately after ironing. It is not necessary to let the iron cool down first. Do not use the heat-resistant protective cover during ironing. 1 Wind the mains cord around the cord storage facility and fix it with the cord clip. 2 Put the iron on the heat-resistant protective cover.
ENGLISH Guarantee and service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Consumer Care Centre in your country, go to your local Philips dealer. Troubleshooting If the appliance does not work or does not work properly, first check the list below.
ENGLISH Problem The iron does not produce any steam. The iron does not produce a steam boost. Possible cause There is not enough water in the water tank. 23 Solution Fill the water tank (see chapter ‘Preparing for use’, section ‘Filling the water tank’). The steam Set the steam control to control is set to a position between 1 and position 0. 6 (see chapter ‘Using the appliance’, section ‘Steam ironing’).
ENGLISH Problem Possible cause The iron is not hot enough. Water droplets drip onto the fabric during ironing. You have not closed the cap of the filling opening properly. You have put an additive in the water tank. The set temperature is too low for steam ironing. Solution Set an ironing temperature at which the steam boost function can be used ( 3 to MAX). Put the iron on its heel and wait until the temperature light has gone out before you use the steam boost function.
ENGLISH Problem Water drips from the soleplate after the iron has cooled down or has been stored. Flakes and impurities come out of the soleplate during ironing. Possible cause You have used the steam boost function at a temperature setting below 3. You have put the iron in horizontal position with water still left in the water tank. Hard water forms flakes inside the soleplate. 25 Solution Set the temperature dial to a setting between 3 and MAX. Empty the water tank.
ENGLISH Problem The red light flashes (specific types only). The iron makes a humming sound. The humming sound stops, although the Ionic DeepSteam function is on. Possible cause The automatic shut-off function has switched off the iron (see chapter ‘Features’, section ‘Automatic shutoff function’). The Ionic DeepSteam function is on. The sound stopped because you placed the iron on its heel. Solution Move the iron slightly to deactivate the automatic shut-off function.
BAHASA MELAYU 27 Pengenalan Tahniah atas pembelian anda, dan selamat datang ke Philips! Untuk mendapat manfaat sepenuhnya daripada sokongan yang ditawarkan oleh Philips, daftarkan produk anda di www.philips.com/welcome. Perihalan umum (Gamb.
BAHASA MELAYU Bahaya -- Jangan sekali-kali tenggelamkan seterika di dalam air. Amaran -- Periksa sama ada voltan yang ditandakan di atas plat jenis sepadan dengan voltan sesalur kuasa setempat sebelum anda menyambungkan perkakas. -- Jangan gunakan perkakas jika plag, kord sesalur kuasa atau perkakas itu sendiri menunjukkan kerosakan yang nyata, atau jika perkakas telah terjatuh atau bocor.
BAHASA MELAYU 29 -- Bahagian plat tapak seterika boleh menjadi amat panas dan mungkin menyebabkan kelecuran jika tersentuh. -- Apabila anda selesai menyeterika, apabila anda membersihkan perkakas, apabila anda mengisi atau mengosongkan tangki air dan juga apabila anda meninggalkan seterika tanpa dijaga biarpun seketika: tetapkan kawalan stim di kedudukan 0, dirikan seterika pada tumitnya dan cabut plag sesalur dari soket dinding.
BAHASA MELAYU Bersedia untuk menggunakan Mengisi tangki air. Jenis air yang harus digunakan Anda boleh menggunakan air paip biasa untuk mengisi tangki air. Petua: Jika air paip di kawasan anda amat liat, kami menasihatkan supaya anda mencampurkannya dengan jumlah air suling yang sama banyak. Jangan gunakan air suling semata-mata. 1 Pastikan palam perkakas ditanggalkan. 2 Setkan pengawal stim pada kedudukan 0 (= tiada stim). 3 Bukakan tukup bukaan isian.
BAHASA MELAYU 31 Memilih tetapan suhu dan stim Tetapan suhu dan stim Jenis fabrik Tetapan suhu Tetapan stim Pancutan stim Pencetus Ionic DeepSteam (jenis tertentu sahaja) Linen MAX 5-6 \ ya Kain kapas 3 3-4 \ ya Wul 2 1-2 Tidak Berkaitan ya Sutera 1 0 Tidak Berkaitan Tidak Berkaitan Fabrik sintetik (cth.
BAHASA MELAYU 3 Untuk menetapkan suhu penyeterikaan yang diperlukan, pusing tombol suhu ke kedudukan yang sesuai (lihat jadual ‘Tetapan suhu dan stim’ di atas). Periksa label penjagaan pada kain kotor untuk mengetahui jenis fabriknya. Jika anda tidak tahu jenis kain sesuatu pakaian itu diperbuat, tentukan suhu penyeterikaan yang betul dengan menyeterika bahagian pakaian yang tidak kelihatan apabila anda memakai atau menggunakan pakaian tersebut.
BAHASA MELAYU 33 Penyeterikaan tanpa stim 1 Setkan pengawal stim pada kedudukan 0 (= tiada stim). 2 Tetapkan suhu penyeterikaan yang diperlukan (lihat bab ‘Bersedia untuk menggunakannya’, bahagian ‘Memilih tetapan suhu dan stim’). Penyeterikaan stim 1 Pastikan bahawa terdapat air di dalam tangki air. 2 Tetapkan suhu penyeterikaan yang diperlukan (lihat bab ‘Bersedia untuk menggunakannya’, bahagian ‘Memilih tetapan suhu dan stim’).
BAHASA MELAYU Menyeterika dengan Ionic DeepSteam (jenis tertentu sahaja) Apabila anda menggunakan fungsi Ionic DeepSteam semasa penyeterikaan stim, stim yang dikeluarkan adalah lebih halus daripada semasa penyeterikaan stim yang biasa. Stim halus meresap lebih jauh ke dalam kain, terutamanya ke dalam fabrik yang tebal. Ini membantu anda menghilangkan kedutan degil dengan lebih mudah. 1 Pastikan bahawa terdapat air di dalam tangki air.
BAHASA MELAYU 35 Nota: Fungsi Ionic DeepSteam hanya berkesan apabila ia digunakan bersama dengan tetapan stim dan tetapan suhu antara 2 dan MAX. Nota: Jangan gunakan fungsi Ionic DeepSteam apabila anda menyeterika tanpa stim dan/atau pada tetapan suhu yang rendah. Namun, penyeterikaan pada suhu rendah tanpa stim dengan fungsi Ionic DeepSteam dihidupkan tidak akan merosakkan seterika. Nota: Output Ionic DeepSteam mungkin berbeza dari masa ke semasa, bergantung kepada suhu penyeterikaan.
BAHASA MELAYU Pancutan stim menegak 1 Anda juga boleh menggunakan fungsi pancutan stim apabila anda memegang seterika secara menegak. Ini berguna untuk melicinkan kedut pada pakaian yang tergantung, langsir, dsb. Jangan sekali-kali menghalakan stim kepada orang. Penghenti titisan Seterika ini dilengkapi fungsi penghenti titisan: seterika berhenti menghasilkan stim secara automatik apabila suhu terlalu rendah supaya air tidak menitis keluar dari plat tapak.
BAHASA MELAYU 37 Nota: Jika lampu pandu kuning jingga tidak menyala selepas anda menggerakkan seterika, plat tapak masih berada pada suhu yang betul dan seterika sedia untuk digunakan. Pembersihan dan penyelenggaraan Pembersihan 1 Setkan kawalan stim pada kedudukan 0, tanggalkan plag dari soket dinding dan biarkan seterika menyejuk. 2 Kesat emping dan apa-apa sisa lain pada plat tapak dengan kain yang lembap dan agen pembersih (cecair) yang tidak melelas.
BAHASA MELAYU serpihan keluar dari plat dasar semasa menyeterika), anda harus menggunakan fungsi Pembersihan Kerak dengan lebih kerap. 1 Pastikan palam perkakas ditanggalkan. 2 Tetapkan pengawal stim pada kedudukan 0. 3 Isikan tangki air hingga ke paras MAX. Jangan masukkan cuka atau agen penanggal kerak yang lain ke dalam tangki air. 4 Tetapkan suhu tombol pada MAX. 5 Masukkan plag ke dalam soket dinding yang dibumikan. 6 Cabut plag seterika apabila lampu suhu padam.
BAHASA MELAYU 39 3 Seka alat seterika yang panas itu secara lembut dengan kain terpakai untuk menghilangkan sisa air yang mungkin ada di tapak alat. 4 Biarkan seterika sehingga sejuk sebelum anda menyimpannya. Penyimpanan 1 Tetapkan kawalan stim pada kedudukan 0 dan cabut plag seterika. 2 Kosongkan tangki air. 3 Biarkan seterika sejuk dahulu di tempat yang selamat. 4 Gulung kord sesalur kuasa melingkari kemudahan simpanan kord dan tetapkan di tempatnya menggunakan klip kord.
BAHASA MELAYU Alam sekitar -- Jangan buang perkakas bersama sampah rumah biasa pada akhir hayatnya, tetapi bawanya ke pusat pungutan rasmi untuk dikitar semula. Dengan melakukan sedemikian anda akan membantu memelihara alam sekitar. Jaminan dan perkhidmatan Jika anda memerlukan maklumat atau jika anda menghadapi masalah, sila lawati laman web Philips di www.philips.com atau hubungi Pusat Penjagaan Pelanggan Philips di negara anda (anda boleh mendapatkan nombor telefonnya dalam risalah jaminan sedunia).
BAHASA MELAYU 41 Masalah Penyebab yang mungkin Penyelesaian Plag seterika dipasang tetapi plat tapak dingin. Terdapat masalah sambungan. Periksa kord sesalur kuasa, palam dan soket dinding. Tombol suhu ditetapkan pada MIN. Tetapkan tombol suhu di kedudukan yang dikehendaki. Seterika tidak menghasilkan stim. Air di dalam tangki Isikan tangki air (lihat air tidak mencukupi. bab ‘Bersedia untuk menggunakannya’, bahagian ‘Mengisi tangki air’.) Pengawal stim telah ditetapkan pada kedudukan 0.
BAHASA MELAYU Masalah Titisan air menitik pada fabrik semasa menyeterika. Penyebab yang mungkin Penyelesaian Panasnya alat seterika kurang. Tetapkan suhu penyeterikaan kepada yang membolehkan fungsi pancutan stim digunakan ( 3 hingga MAX). Dirikan seterika di atas tumitnya dan tunggu sehingga lampu suhu telah padam sebelum anda menggunakan fungsi pancutan stim. Tekan tukup sehingga anda Anda tidak mendengar bunyi klik. menutup tukup bukaan isian dengan betul.
BAHASA MELAYU 43 Masalah Penyebab yang mungkin Penyelesaian Air menitis dari plat tapak setelah seterika sejuk atau setelah disimpan. Anda telah meletakkan seterika dalam kedudukan mendatar dengan air masih tertinggal di dalam tangki air. Kosongkan tangki air. Air liat membentuk Emping dan kotoran keluar emping di dalam plat tapak. dari plat tapak semasa menyeterika.
BAHASA MELAYU Masalah Penyebab yang mungkin Penyelesaian Bunyi berdengung akan terhenti, walaupun fungsi Ionic DeepSteam masih hidup. Bunyi itu terhenti kerana anda meletakkan seterika pada tumitnya. Bunyi berdengung akan kedengaran kembali sebaik sahaja anda meneruskan penyeterikaan.
繁體中文 45 簡介 恭喜您購買本產品並歡迎加入飛利浦!請於 www.philips.
繁體中文 警示 -- 在使用前,請先檢查標籤上所標示的電壓是 否與當地的電源系統電壓一致。 -- 插頭、電源線或產品本身受損時,或是產品 曾摔落或漏電時,請勿使用。 -- 如果電線損壞,則必須交由飛利浦、飛利浦 授權之服務中心,或是具備相同資格的技師 更換,以免發生危險。 -- 當本產品連接到電源時,必須有人看顧。 -- 基於安全考慮,在缺乏監督及適當指示之 下,本產品不適用於孩童及任何身體、知 覺、或心理功能障礙者,或缺乏使用經驗及 知識者。 -- 請勿讓孩童使用本產品或將本產品當成玩 具。 -- 請勿讓電源線靠近接觸熨斗的發熱底盤。 警告 -- 只將產品連接到有接地的電源插座。 -- 定期檢查電線是否受損。 -- 熨斗的底盤可能會變得很燙,如果碰到可能 會燙傷。 -- 當您熨燙完畢、清理熨斗、倒乾水箱的水或 加水,或即使短暫離開熨斗時:請將蒸氣控 制鈕設定到 0 的位置,將熨斗直立在其跟部 上,並且將電源插頭從插座拔出。 -- 請將熨斗放置在平穩的水平面上使用。 -- 請勿將香水、醋、澱粉、除水垢劑、熨燙添 加劑或其他化學物質加入水箱中。 -- 本產品僅供家用。 電磁波 (EMF) 本飛利浦產品符
繁體中文 47 第一次使用 1 撕下底盤上所有貼紙、保護膜或塑膠膜。 2 清洗注水杯並將其風乾。 使用前準備 加水至水箱內 使用哪些類型的水 您可以在水箱中注入一般自來水。 提示: 如果在您居住地區的自來水質硬度很 高,我們建議您用等量的蒸餾水調合。請勿僅 使用蒸餾水。 1 確定產品的插頭已經拔離電源插座。 2 請將蒸氣控制設定到 0 的位置 (= 無蒸氣)。 3 將注水口的蓋子打開。 4 將熨斗向後傾斜,以注水杯盛裝自來水注入 水箱,最多到水箱的最高容量為止。 切勿注入超過「MAX」的水位指示。 請勿將香水、醋、澱粉、除水垢劑、熨燙添加 劑或其他化學物質加入水箱中。
繁體中文 5 蓋上加水蓋 (可聽見喀噠聲)。 選取溫度和蒸汽設定 溫度和蒸氣設定 布料種類 溫度設 定 蒸氣設 定 強力蒸 氣 亞麻布 MAX 最 大 5-6 棉 3 3-4 毛料 2 1-2 無 是 絲 1 0 無 無 合成纖維 (例如 壓克力纖維、尼 龍、聚醯胺、聚 酯纖維) 1 0 無 無 \ \ 離子深層蒸 氣 (限特定 機型) 是 是 注意: 如上表所示,請勿於低溫使用蒸氣或強 力蒸氣,否則熱水會從熨斗漏出。 1 限特定機型:取下防燙護板。 在熨燙期間請勿將防燙護板留在底盤上。 2 將熨斗直立。
繁體中文 49 3 設定所需的熨燙溫度時,請將溫度控制設定 調到適當的位置 (請參閱上方的「溫度和蒸 汽設定」表)。 檢查洗濯指示標籤上的布料種類。 如果您不知道衣料是由哪一種纖維製成,請先 在該衣料不起眼的部份試燙,以判斷適當的熨 燙溫度。 絲質、毛料和合成纖維:熨燙布料的背面以防 止衣料發亮。請勿使用噴水功能,以防止產生 印漬。 請從需要最低溫的衣物開始熨燙,例如合成纖 維製的衣料。 4 設定適當的蒸汽設定 (請參閱上方的「溫度 和蒸汽設定」表)。 5 將電源線插頭插入接地插座中。 ,, 琥珀色溫度指示燈會亮起。 6 當琥珀色溫度指示燈熄滅時,請先稍待一 會兒再開始熨燙。 ,, 熨燙期間,溫度指示燈會間歇性地亮起。 使用此產品 注意: 第一次使用時,熨斗可能會產生一 些煙霧,煙霧會在不久後消失。
繁體中文 無蒸氣熨燙 1 請將蒸氣控制設定到 0 的位置 (= 無蒸氣)。 2 設定所需的熨燙溫度 (請參閱「使用前準 備」單元的「選取溫度和蒸汽設定」一節) 。 蒸氣熨燙 1 確定水箱有水。 2 設定所需的熨燙溫度 (請參閱「使用前準 備」單元的「選取溫度和蒸汽設定」一節) 。 3 設定適當的蒸汽設定 (請參閱「使用前準 備」單元的「選取溫度和蒸汽設定」一節) 。 注意: 到達設定溫度時,熨斗便會立即開始產 生蒸氣。
繁體中文 51 以強力蒸汽進行蒸汽熨燙 1 以強力蒸汽進行熨燙時,請按住強力蒸汽按 鈕。 離子深層蒸氣熨燙功能 (限特定機型) 若您在蒸氣熨燙時使用離子深層蒸氣熨燙功 能,熨斗將產生較一般蒸氣熨燙時更細緻的蒸 氣。細緻的蒸氣可滲透至深處 (尤其是厚重的衣 料),幫助您輕鬆擺平頑強的皺褶。 1 確定水箱有水。 2 設定所需的熨燙溫度 (請參閱「使用前準 備」單元的「選取溫度和蒸汽設定」一節) 。 3 設定適當的蒸汽設定 (請參閱「使用前準 備」單元的「選取溫度和蒸汽設定」一節) 。 4 按一下離子深層蒸汽按鈕,開啟離子深層蒸 汽功能。 ,, 藍色的離子深層蒸氣指示燈即亮起,隨後您 會聽到嗡嗡聲。 ,, 熨斗會產生離子深層蒸氣,幫助您有效去除 各種頑強的皺褶。
繁體中文 5 再按一下離子深層蒸汽按鈕,關閉負離子深 層蒸汽功能。 注意: 您必須同時使用蒸氣設定,且溫度設定 必須介於 2 到 MAX 之間,離子深層蒸氣熨燙 功能才可發揮功效。 注意: 若您不使用蒸氣且/或以低溫設定熨燙 時,請勿使用離子深層蒸氣熨燙功能。但是若 不開啟蒸氣設定,而以低溫配合離子深層蒸氣 進行熨燙,熨斗不會有所損傷。 注意: 熨斗每次產生的離子深層蒸氣可能因熨 燙溫度不同而有所差異。 功能 噴水功能 您可以在任何溫度下使用噴水功能,以潤溼衣 服。這有助於消除頑強的皺摺。 1 確定水箱有水。 2 按噴水按鈕數下,以潤溼衣服。 強力蒸氣功能 特殊 Steam Tip 蒸汽頭底盤噴出的強力蒸汽有 助於移除頑強的皺褶。強力噴射蒸汽讓蒸汽更 均勻散佈到衣物各處。 強力噴射蒸汽功能只能用在 3 到 MAX 之間 的溫度設定。
繁體中文 53 1 按下並放開強力蒸氣按鈕。 垂直蒸汽釋放 1 當您垂直握住熨斗時,也可以使用強力噴 射蒸汽功能。 用以移除吊掛衣服、窗簾等之縐褶時很有用。 切勿直接對著人噴射蒸氣。 特殊底盤防漏功能 本熨斗配有特殊底盤防漏功能:當溫度太低時 熨斗會自動停止產生蒸氣,以避免水從底盤滴 下。當您聽到一個聲音時,表示已開啟此功 能。 自動斷電功能 (限特定機型) 如果熨斗已有一段時間未被移動,自動斷電功 能會自動關閉熨斗電源。 ,, 紅色自動斷電指示燈閃爍時,表示自動斷電 功能已經關閉熨斗電源。 若要讓熨斗再次加熱: 1 拿起熨斗或稍微移動。 ,, 紅色自動斷電指示燈熄滅。 ,, 如果底盤溫度已經低於熨燙溫度,則琥珀色 溫度指示燈會亮起。 2 如果琥珀色指示燈在移動熨斗後亮起,請等 指示燈熄滅後再開始熨燙。
繁體中文 注意: 如果琥珀色指示燈在移動熨斗後並未亮 起,表示底盤仍保持在適當的溫度,熨斗可開 始熨燙。 清潔與維護 清潔 1 設定蒸汽控制鈕到 0 的位置。將電源插頭從 插座上拔除並讓熨斗冷卻。 2 以乾的抹布和非研磨性 (液態) 清潔劑,擦掉 底盤上的薄片及其他的沈積物。 為保持底盤滑順,請避免底盤與金屬物品直接 碰觸。禁止使用鋼絲絨、醋或其他的化學物質 清潔底盤。 3 請用溼布清潔熨斗上面的部份。 4 定期以清水沖洗水箱,沖洗後請將水箱內的 水倒光。 雙效抗鈣除垢系統 -- 除鈣錠能預防蒸汽孔沈積水垢。此除鈣錠能 持續作用,不需 更換。 -- 除鈣清洗功能可去除熨斗中的水垢雜質。 使用除鈣功能 每兩週使用一次除鈣功能。如果居住地的水質 非常硬 (亦即在熨燙過程中有小薄片從底盤產 生),則必須更頻繁地使用除鈣功能。 1 確定產品的插頭已經拔離電源插座。 2 將蒸汽控制設定到 0 的位置。 3 將水倒入水箱至 MAX 刻度。 切勿將醋或其他除鏽劑倒入水箱內。
繁體中文 55 4 將溫度控制設定到「MAX」。 5 將插頭插入接地插座中。 6 溫度指示燈熄滅時,請拔除熨斗的插頭。 7 將熨斗拿到洗手槽上方,按住除垢按鈕不 放,輕輕地前後搖晃熨斗。 ,, 蒸氣和滾水將會從底盤流出。雜質和白色的 小薄片 (如果有的話) 將會被沖出來。 8 當水箱內的水全部流光後,即放開除垢清洗 按鈕。 9 如果熨斗內仍有許多雜質,請重複除鈣清洗 的過程。 除鈣清洗之後 1 將插頭插回插座中使熨斗加熱,讓底盤變 乾。 2 當熨斗到達設定的熨燙溫度時,將熨斗的插 頭拔掉。 3 將熱的熨斗輕輕地在用過的布料上摩擦,以 將底盤上已形成的水漬擦拭乾淨。 4 在您將熨斗收藏前,請先讓其冷卻。 收納 1 將蒸汽控制鈕設定在 0 的位置,並拔除熨斗 插頭。
繁體中文 2 將水箱內的水倒光。 3 將熨斗置於安全的地方進行冷卻。 4 將電線捲繞在電線放置的地方,並用其固定 夾將電源線固定起來。 5 將熨斗直立存放於乾燥且安全的地方。 防燙護板 (限特定機型) 熨燙衣物後,可以立即將熨斗放置在防燙護 板。不一定要先讓熨斗冷卻。 在熨燙間切勿使用防燙護板。 1 將電線捲繞在電線放置的地方,並用其固定 夾將電源線固定起來。 2 將熨斗放在防燙護板上。 環境保護 -- 本產品壽命結束時請勿與一般家庭廢棄物一 併丟棄。請將該產品放置於政府指定的回收 站,此舉能為環保盡一份心力。
繁體中文 57 保固與服務 若您需要相關資訊,或是有任何問題,請瀏覽 飛利浦網站,網址為 www.philips.
繁體中文 問題 可能原因 解決方法 熨斗沒有產 生強力蒸 氣。 您在非常短的時 間內過度使用強 力噴射蒸汽功 能。 請保持水平位置繼續熨燙,靜 待一陣子之後,再使用強力蒸 氣功能。 熨斗不夠燙。 設定適合使用強力噴射蒸汽功 能 (3 到 MAX) 的溫度。 將熨斗直立,靜待指示燈熄滅 後再開始使用強力噴射蒸汽 功能。 您沒有正確地蓋 上加水蓋。 按壓加水蓋,直到聽到喀搭 聲。 您已將添加物加 進水箱中。 以水清洗水箱,不要將任何的 添加物倒入水箱中。 設定的熨燙溫度 太低,無法進行 蒸汽熨燙。 設定或 2 更高的溫度。 您在溫度設定為 3 以下時, 使用強力蒸氣功 能。 把溫度控制設定調到 3 與 MAX 之間的設定。 熨斗冷卻後 或在儲藏 時,底盤會 滴水。 在水箱裡還有水 時,將熨斗平 放。 將水箱內的水倒光。 在熨燙過程 中會有小薄 片和雜質從 底盤產生。 硬水在底盤內側 形成小薄片。 請使用除鈣清洗功能一次或 數次 (請參閱「清潔與維護」 單元的「使用除鈣功能」一 節)。 熨燙時,水 滴滴到衣料 上。
繁體中文 59 問題 可能原因 解決方法 紅色指示燈 閃爍 (限特 定機型)。 稍微移動熨斗,以解除自動斷 自動斷電功能已 關閉熨斗電源 (請 電功能。紅色自動斷電指示燈 會熄滅。 參閱「功能」章 節的「自動斷 電」)。 熨斗發出嗡 嗡聲。 離子深層蒸氣熨 燙功能是在開啟 狀態。 如果在沒有使用蒸汽功能熨燙 時聽到嗡嗡聲,請放開離子深 層蒸汽熨燙按鈕。當您沒有配 合蒸汽設定進行熨燙時,負離 子深層蒸汽熨燙功能不會發揮 作用。 嗡嗡聲停止 時,離子深 層蒸汽熨燙 功能仍然開 啟。 因為您將熨斗直 立,所以嗡嗡聲 停止。 一旦您繼續燙衣服時,嗡嗡聲 即會恢復。
简体中文 简介 感谢您的惠顾,欢迎光临飞利浦! 为了您能充分享受飞利浦提供的支持, 请在 www.philips.
简体中文 61 注意事项 使用本产品之前,请仔细阅读本使用说 明书,并妥善保管以备日后参考。 危险 -- 切勿将熨斗浸泡到水里。 警告 -- 连接产品电源前,请检查型号铭牌所标 示的电压与当地电源电压是否一致。 -- 如果插头、电源线或产品本身已经明 显损坏,或产品曾坠落或出现渗漏, 请勿再使用产品。 -- 如果电源软线损坏,为了避免危险, 必须由制造商、其维修部或类似部门 的专业人员来更换。 -- 在产品接通电源期间,使用者不得离 开。 -- 本产品不打算由肢体不健全、感觉或 精神上有障碍或缺乏相关经验和知识 的人(包括儿童)使用,除非有负责 他们安全的人对他们使用本产品进行 监督或指导。 -- 应照看好儿童,确保他们不玩耍本产 品。 -- 切勿让电源线触及高温电熨斗底板。 注意 -- 产品只能使用带接地线的插座。 -- 定期检查电源线是否损坏。
简体中文 -- 熨斗的底板会变得非常烫,如触摸喷 嘴,则会导致烫伤。 -- 当完成熨烫、清洁产品、为水箱加水 或将水倒出水箱,乃至短时间离开本 产品时:请将蒸汽控制旋钮设定到位 置 O,将熨斗竖放,并从电源插座上 拔下电源线。 -- 一定要在稳固、平整且水平的表面上 放置和使用熨斗。 -- 切勿将香水、醋、淀粉、除垢剂、 烫衣剂或其它化学品注入水箱内。 -- 本产品仅限于家用。 电磁场 (EMF) 这款飞利浦产品符合关于电磁场 (EMF) 的相关标准。据目前的科学证明,如果 正确使用并按照本用户手册中的说明进 行操作,本产品是安全的。 首次使用之前 1 从熨斗底板取下任何不干胶标签、 保护膜或塑料保护罩。 2 清洗并擦干注水杯。
简体中文 63 使用准备 给水箱注水 应使用的水质类型 您可以使用普通自来水注入水箱。 提示: 如果您所在地区的自来水硬度 很高,我们建议您将自来水与等量的 蒸馏水混合后再使用。请勿仅使用蒸 馏水。 1 确保已经拔下产品的电源插头。 2 将蒸汽控制旋钮调至位置 0 (=无蒸汽)。 3 打开注水口的盖子。 4 向后倾斜熨斗,使用注水杯向水箱 注入自来水,直至注到水箱最大值 标示处。 切勿让水位超过最大 (MAX) 水位标示。 切勿将香水、醋、淀粉、除垢剂、 烫衣剂或其它化学品注入水箱内。 5 盖上注水口的盖子 (可听到“咔哒”一声)。
简体中文 选择温度和蒸汽设定 温度和蒸汽设定 面料类型 麻 温度设 蒸汽设 蒸汽喷 深层离子 定 定 射 蒸汽(仅 限于特定 型号) 最大 5-6 是 \ 棉 3 羊毛 2 丝绸 1 合成纤维 1 (如聚丙烯、 尼龙、聚酰 胺、聚脂) 3-4 1-2 0 0 \ 不适用 不适用 不适用 是 是 不适用 不适用 注意: 确保您选择的蒸汽设定适合所 设定的熨烫温度。 1 仅限于特定型号:除去隔热保护 盖。 在熨烫过程中,不要将隔热保护盖遗留 在底板上。 2 将熨斗竖立。
简体中文 65 3 要设定所需的熨烫温度,请将温度 转盘旋转到适当位置(见“温度和 蒸汽设定”表格)。 检查衣服标签以确定面料类型。 如果您不知衣物是由何种纤维组成, 找一处穿时看不见的地方熨, 试试何种温度最合适。 丝绸,羊毛及合成纤维:应当熨其反 面,以防产生局部发亮。为避免产生水 渍印,请勿使用喷雾功能。 从需要最低熨烫温度的布料开始熨烫, 如合成纤维织物。 4 设置适当的蒸汽设定(见上面的“ 温度和蒸汽设定”表格)。 5 将插头插入有接地的电源插座。 ,,黄色温度指示灯亮起。 6 当琥珀色温度指示灯熄灭后, 在开始熨烫之前请稍等片刻。 ,,在熨烫期间,温度指示灯会时亮时 灭。
简体中文 使用本产品 注意: 首次使用时,熨斗可能会冒轻 烟。 过一会就会停止。 无蒸汽熨烫 1 将蒸汽控制旋钮调至位置 0 (=无蒸汽)。 2 设定所需的熨烫温度 (见“使用准备”一 章中的 “选择温度和蒸汽设定”一节)。 蒸汽熨烫 1 确保水箱中有水。 2 设定所需的熨烫温度(见“使用准 备”一 章中的“选择温度和蒸汽设 定”一节)。
简体中文 67 3 设置合适的蒸汽设定(见“使用准 备”一 章中的“选择温度和蒸汽设 定”一节)。 注意: 熨斗将在达到设定温度时立即 开始产生蒸汽。 使用加强蒸汽进行蒸汽熨烫 1 要想在熨烫过程中使用加强蒸汽, 请按住蒸汽蒸汽束喷射按钮 使用深层离子蒸汽进行熨烫 (仅限于特定型号) 当您在蒸汽熨烫过程中使用深层离子蒸 汽功能时,产生的蒸汽要比普通蒸汽更 微小。更微小的蒸汽能够更加深入织 物,尤其是较厚的面料深处。这有助于 您轻松去除顽固皱褶。 1 确保水箱中有水。 2 设定所需的熨烫温度(见“使用准 备”一 章中的“选择温度和蒸汽设 定”一节)。
简体中文 3 设置合适的蒸汽设定(见“使用准 备”一 章中的“选择温度和蒸汽设 定”一节)。 4 按一次深层离子蒸汽按钮打开深层 离子蒸汽功能。 ,,蓝色的深层离子蒸汽指示灯亮起, 熨斗会发出嗡嗡声。 ,,熨斗能产生深层离子蒸汽,帮助您去 除使是最顽固的褶皱。 5 再次按深层离子蒸汽按钮关闭深层 离子蒸汽功能。 注意: 只有在结合蒸汽设定以及 2 和最高 (MAX) 之间的温度设定使用 时,深层离子蒸汽功能才有效果。 注意: 在不使用蒸汽进行熨烫和(或) 低温设定时,请勿使用深层离子蒸汽功 能。但是,即使在不使用蒸汽进行低温 熨烫时,打开深层离子蒸汽功能也不会 损坏熨斗。 注意: 深层离子蒸汽输出可能时常发 生变化,这取决于熨烫温度。
简体中文 69 功能 喷水功能 您可以在任意温度下使用喷水功能,湿 润要熨烫的布料。这有助于去除顽固的 褶皱。 1 确保水箱中有水。 2 按几次喷水按钮,把要熨烫的布料 弄湿。 蒸汽喷射功能 特制的底板前端尖型设计,会喷出蒸 汽束, 帮助去除顽固的皱褶。喷射的蒸汽束能 将蒸汽渗透到衣物的任何细微之处。 蒸汽喷射功能只能在 3 到最高 (MAX) 温度设定之间使用。 1 按下并释放蒸汽喷射按钮。 垂直蒸汽束喷射 1 您也可以在熨斗直立时使用蒸汽喷 射功能。 蒸汽束喷射可用于去除悬挂的衣物、 窗帘上的褶皱。 不要将蒸汽直接对着他人。
简体中文 防滴漏功能 该熨斗具有防滴漏功能:当温度太低 时,熨斗将自动停止产生蒸汽,防止水 从熨斗底板滴漏。当此现象发生时, 您会听到一声响声。 自动关熄功能(仅限于特定型号) 如果熨斗在一段时间内没有移动,自动 关熄功能将自动切断熨斗电源。 ,,红色自动关熄指示灯闪烁,表示自动 关熄功能已切断熨斗电源。 让熨斗再次加热: 1 将熨斗拿起或稍微动一下。 ,,红色自动关熄指示灯将熄灭。 ,,如果底板的温度降到低于设定的熨烫 温度,黄色温度指示灯将亮起。 2 如果移动熨斗后,黄色温度指示灯 亮起,则应等其熄灭后才能开始熨 烫。 注意: 如果移动熨斗后,黄色温度指 示灯没有亮起,则说明底板温度仍可继 续熨烫。 清洁和保养 清洁 1 将蒸汽控制旋钮设定到位置 0,从 插座中拔下电源插头,让熨斗充分 冷却。
简体中文 71 2 用湿布和非腐蚀性(液体)清洁剂 抹去底板上的水垢和其它沉积物。 为了保持底板光滑,应避免底板与金属物 体碰撞。切勿使用磨砂布、醋或其他化学 品清洁底板。 3 用湿布清洁熨斗的上部。 4 定期用水冲洗水箱。冲洗之后将水 箱中的水全部倒出。 双效除垢系统 -- 防水垢片可防止水垢堵塞蒸汽孔。 此防水垢片持续有效,无须更换。 -- 除垢功能可以从熨斗除去水垢颗粒。 使用自动除垢功能 建议两周使用一次自动除垢功能。如果 您所在地区的水质很硬(即在熨烫过程 中底板出现水垢薄片时),可增加使用 自动除垢功能的次数。 1 确保已经拔下产品的电源插头。 2 将蒸汽控制旋钮转到 0 位。 3 给水箱注水,直至最大水位 (MAX)。 不要将醋或其它除垢剂注入水箱。 4 将温度转盘调至最大 (MAX)。 5 将插头插入有接地的电源插座。 6 当温度指示灯熄灭时,拔下熨斗的电 源插头。
简体中文 7 握住熨斗的水槽上方,然后按下 自动除垢按钮并轻轻地来回晃动熨 斗。 ,,蒸汽和沸水从熨斗底板流出。杂质和 水垢 (如果有)将被冲出。 8 一旦水箱中的水用完后,松开 “清除水垢”按钮。 9 如果熨斗中仍存在大量杂质, 请重复执行除水垢步骤。 完成除水垢过程后 1 将插头插回插座,让熨斗加热, 以将底板烘干。 2 当达到设定的熨烫温度后, 拔下熨斗的电源插头。 3 将热熨斗放在一块用过的布上轻轻 地前后移动,以除去留在底板上的 水渍。 4 让熨斗冷却,然后存放好。 存储 1 将蒸汽控制设置到位置 0 并拔下熨 斗的电源插头。 2 倒空水箱。 3 将熨斗放在安全的位置冷却。
简体中文 73 4 将电源线缠绕在电源线存储装置 上, 然后用线夹固定。 5 请将熨斗竖放在干燥安全的地方。 隔热保护盖(仅限于特定型号) 可以在熨烫之后立即将熨斗存放在隔 热保护盖上。没有必要先让熨斗冷却 下来。 熨烫时,不要使用隔热保护盖。 1 将电源线缠绕在电源线存储装置上, 然后用线夹固定。 2 将熨斗装上隔热保护盖。 环保 -- 弃置产品时,请不要将其与一般生活 垃圾堆放在一起;应将其交给官方指 定的回收中心。这样做有利于环保。
简体中文 保修与服务 如果您需要了解信息, 或者有任何疑问,请访问飞利浦网站: www.philips.
简体中文 问题 熨斗不产 生蒸汽喷 射。 熨烫时, 水滴会滴 在布料 上。 75 可能的原因 解决方法 蒸汽控制旋钮 将蒸汽控制旋钮设定在 转到了 0 位。 1 到 6 之间(见“使用 产品”一章的“蒸汽熨 烫”一节)。 熨斗不够热并 设定适合蒸汽熨烫的温度 且/或防滴漏功 (3 到 MAX 之间)。 能已经启动。 将熨斗竖立,等待温度 指示灯熄灭,然后再开 始熨烫。 您在很短的时 持续按水平方向熨烫, 间内过于频繁 稍等片刻后再使用蒸汽 地使用了蒸汽 喷射功能。 喷射功能。 熨斗不够热。 将熨烫温度设置到可以 使用蒸汽喷射功能的水 平(3 到 MAX 之 间)。将熨斗竖立,等 到温度指示灯熄灭再使 用蒸汽喷射功能。 您没有正确地 按下盖子,直到听到喀 盖上注水口 哒一声。 盖。 您在水箱中放 入了添加剂。 设定温度太 低,无法进行 蒸汽熨烫。 漂洗水箱并且不要往水 箱内注入任何添加剂。 设定 2 或更高的温 度。
简体中文 问题 可能的原因 您在温度设定 低于 3 的 情况下使用蒸 汽喷射功能。 熨斗冷却 您在水箱仍然 后,或存放 有水的情况下 期间,有水 将熨斗水平放 从底板漏 置。 出。 在熨烫过程 硬水会在底板 中底板内冒 内形成水垢。 出水垢和杂 质。 红色指示灯 自动关熄功能 闪烁(仅 已关闭熨斗 限于特定型 电源 号)。 (见“功能” 一章“自动关 熄功能”一 节)。 熨斗发出嗡 深层离子蒸汽 嗡声。 功能已开启。 解决方法 将温度旋钮调到 3 与 MAX 之间的设置。 倒空水箱。 一次或多次使用自动除 垢功能(见“清洁和保 养”一章“使用自动除 垢功能”一节)。 轻轻移动熨斗,以解除 自动关熄功能。红色自 动关熄指示灯将熄灭。 如果在不使用蒸汽进行 熨烫时听到嗡嗡声,请 按深层离子蒸汽按钮关 闭深层离子蒸汽功能。 深层离子蒸汽功能在不 使用蒸汽进行熨烫时不 起作用。
简体中文 问题 虽然深层离 子蒸汽功能 仍然开启, 但是嗡嗡声 停了下来。 可能的原因 解决方法 声音停止是因 一旦您继续熨烫, 为您将熨斗竖 嗡嗡声即会恢复。 放了。 18/04/2014 77
4329.000.8208.