PIAGGIO WOULD LIKE TO THANK YOU for choosing one of its products. We have prepared this booklet to help you to get the very best from your scooter. Please read it carefully before riding the scooter for the first time. It contains information, tips and precautions for using your scooter. It also describes features, details and devices to assure you that you have made the right choice.
The instructions given in this manual are intended to provide a clear, simple guide to using your scooter; this booklet also details routine maintenance procedures and regular checks that should be carried out on the vehicle at an authorised Dealer or Service Centre. The booklet also contains instructions for simple repairs.
Personal safety Failure to completely observe these instructions will result in serious risk of personal injury. Safeguarding the environment Sections marked with this symbol indicate the correct use of the vehicle to prevent damaging the environment. Vehicle intactness The incomplete or non-observance of these regulations leads to the risk of serious damage to the vehicle and sometimes even the invalidity of the guarantee. The signs that you see on this page are very important.
INDEX VEHICLE...................................................................................... Dashboard................................................................................ Analogue instrument panel....................................................... Clock......................................................................................... Key switch................................................................................. Locking the steering wheel............................
TECHNICAL DATA...................................................................... Kit equipment............................................................................ SPARE PARTS AND ACCESSORIES........................................ Warnings................................................................................... PROGRAMMED MAINTENANCE............................................... Scheduled maintenance table................................................... Selènia Moto Rider..........
Beverly 500 Chap.
Dashboard (01_01) A = Ignition key-switch B = Starter button C = Throttle control D = Front brake lever E = Cooling hatch 01_01 F = Turn signal switch G = Light switch with passing H = Rear brake control I = Horn button L = Switch pre-installation M = Bag hook N = Saddle opening electric switch O = Switch pre-installation PI = Engine cut-off switch Q = Instrument panel Analogue instrument panel (01_02) A = Speedometer (km/h) B = Odometer 1 Vehicle C = Trip odometer D = Oil pressure warning light 01_02
G = Immobilizer LED H = Fuel gauge I = Low fuel warning light L = Headlight warning light M = Right turn indicator warning light N = Injection telltale light O = Odometer reset button P = Left turn indicator warning light Q = Speedometer (mph) R = Digital clock S = Clock controls Clock (01_03) Hours and minutes are displayed in a 1 to 12 format on the instrument panel; operating the function selection button «1», month, day and seconds are also displayed besides hours and minutes.
Key switch (01_04) LOCK= Ignition barred, key can be removed, mechanical antitheft device activated. OFF= Ignition barred, key can be removed, mechanical antitheft device deactivated. ON= Prestarting position, key cannot be removed, mechanical antitheft device deactivated. Locking the steering wheel 01_04 Turn the handlebar to the left as far as it will go, turn the key to position «LOCK» and remove the key. Releasing the steering wheel Reinsert the key and turn it to «OFF».
Push the «C» button to sound the horn. 01_06 Light switch (01_07) 0 = Dipped beam/tail light 1 = Upper beam 2 = Passing (flashing) WARNING THE SIDELIGHT BULB REMAINS ALWAYS ON IF THE KEY IS SET TO «ON».
Engine stop button (01_09) 0 = OFF 1 = RUN 01_09 The immobilizer system In order to enhance theft protection, the scooter is equipped with a «PIAGGIO IMMOBILIZER » electronic engine locking device that is activated automatically when the starter key is removed. Upon start-up, the «PIAGGIO IMMOBILIZER» system checks the starter key, and only if this key is recognised will the immobilizer system allow the scooter to be started. Keys (01_10, 01_11, 01_12) 01_10 Two types of keys come with the vehicle.
LOSING THE RED KEY PREVENTS ANY REPAIRS OF THE "PIAGGIO IMMOBILIZER" SYSTEM AND THE ENGINE CONTROL UNIT. WARNING 01_12 KEEP THE "CODE CARD" AND THE RED HANDGRIP KEY IN A SAFE PLACE (NOT ON YOUR VEHICLE). Immobilizerdevice enabled indicator led (01_13) Activation of the «PIAGGIO IMMOBILIZER» system is signalled by a flashing warning light «G» (see «Analogue instrument panel» section).
new storage procedure are deleted from the memory. Any lost keys will therefore not be enabled to start the engine. WARNING EACH KEY HAS ITS OWN AND UNIQUE CODE, WHICH MUST BE STORED BY THE SYSTEM CONTROL UNIT. VIOLENT SHOCKS MAY AFFECT THE ELECTRONIC COMPONENTS OF THE KEY. IF OWNERSHIP OF THE VEHICLE IS TRANSFERRED, THE RED-HANDGRIP KEY (AS WELL AS THE OTHER KEYS) AND THE "CODE CARD" MUST ALSO BE TRANSFERRED TO THE NEW OWNER.
After pulling out the last black key, insert the red key again and turn it to "ON" (this operation should be performed within 10 seconds of pulling out the previous key). Leave it in this position for 1 to 3 seconds and return it to the «OFF» position. Proper programming check Insert the red key disabling the transponder (i.e., tilt the key cap by 90°) and turn the key to "ON". Perform the engine start-up operation. Ensure that the engine does not start.
01_15 Power supply socket (01_16) There is a plug socket "D" inside the helmet compartment. The plug socket may be used for external consumers (mobile phone, inspection light, etc.).
The identification numbers consist of a prefix stamped on the chassis «B» covered by port «A» and on the engine «C», followed by a number. These numbers must always be mentioned on spare parts requests. To read the chassis number, remove the relevant port «A» in the helmet compartment placed under the mat. The chassis number stamped on the vehicle should be checked against that reported onto the vehicle's documents.
Saddle opening button (01_20, 01_21) With the key in position «OFF» or «ON» or with the engine on, you can electrically open the saddle by pressing button «E». If the electric opening does not work, use the emergency lever «A». 01_20 01_21 Rear top box opening 1 Vehicle Insert the key into the switch and press down until the glove compartment opens. In the event that the switch is in «LOCK», turn the key to «OFF» or «ON» before pressing it.
Turn the key in anticlockwise direction and at the same time pulling out the retaining hook as far as it will go. Insert the strap of the helmet inside the hook, then push the hook back inside the front rail of the luggage rack in order to avoid preventing starting. CAUTION 01_22 IN ORDER TO AVOID ENDANGERING THE STABILITY WHEN RIDING, DO NOT RIDE THE SCOOTER WITH THE HELMET INSERTED INTO THE ANTITHEFT DEVICE. N.B.
1 Vehicle
Beverly 500 Chap.
Checks Before using the vehicle, check: 1. There is enough fuel in the fuel tank. 2. Front and rear brake fluid level 3. That tyres are properly inflated. 4. The correct functioning of the tail lights, the headlight, and the turn indicators. 5. The correct functioning of front and rear brakes. 6. The oil level in the gearcase. 7. The engine oil level. 8. The coolant level Refuelling (02_01, 02_02) Fuel: open the door as described in the section «Access to the gas tank» and turn the cap«A».
CAUTION PETROL DAMAGES THE PLASTIC PARTS OF THE BODYWORK. CAUTION 02_02 USING OILS OTHER THAN THOSE RECOMMENDED CAN SHORTEN THE LIFE OF THE ENGINE. CAUTION DO NOT USE THE VEHICLE TO THE COMPLETE EXHAUSTION OF THE FUEL; IN THE EVENT THAT THIS SHOULD OCCUR, DO NOT ATTEMPT TO START THE ENGINE. TURN THE KEY SWITCH TO OFF AND TOP-UP THE TANK AS SOON AS POSSIBLE. FAILURE TO FOLLOW THESE GUIDELINES COULD DAMAGE THE FUEL PUMP AND/OR THE CATALYTIC CONVERTER.
Tyre pressure (02_03) Check periodically (about every 500 km) the pressure and wear of the tyres. The tyres are equipped with wear indicators, according to which the tyres should be changed before these indicators come to the surface of the tread. Check also that the tyres do not have tears on their sides or an irregular pattern of wear on the tread; if this occurs, go to an authorised workshop or at least equipped to perform the replacement.
The preloading of the springs can be adjusted to 4 positions using the ring nut located in the lower part of the shock absorbers and the specific spanner supplied. Minimum preloading Position 1: driver only Medium preloading Position 2: driver and top-box 02_04 Medium preloading Position 3: rider and passenger Maximum preloading Position 4: driver, passenger, and top-box. The specific shock absorber wrench must be used to perform this operation.
WARNING WE STRONGLY RECOMMEND NOT TO ADJUST BOTH SHOCK ABSORBERS WITH DIFFERENT PRELOADING Running in (02_05) WARNING 02_05 DURING THE FIRST 1000 KM DO NOT RIDE THE VEHICLE OVER 80% OF ITS MAXIMUM SPEED. AVOID TWISTING THE THROTTLE GRIP FULLY OR KEEPING A CONSTANT SPEED ALONG LONG SECTIONS OF ROAD. AFTER THE FIRST 1000 KM, GRADUALLY INCREASE SPEED UNTIL REACHING THE MAXIMUM PERFORMANCE.
5. Pull lever «C» of the front or rear brake and then activate the starter button «D». WARNING 02_07 THE AUTOMATIC TRANSMISSION MAKES THE REAR WHEEL TURN EVEN WHEN THE THROTTLE IS SLIGHTLY TWISTED. RELEASE THE BRAKE CAREFULLY AFTER STARTING, AND THEN ACCELERATE GRADUALLY. CAUTION DO NOT START-UP THE ENGINE IN CLOSED AREAS BECAUSE EXHAUST GASES ARE TOXIC.
Stopping the engine (02_08) Fully untwist the throttle grip, then rotate the key in the switch «A » to «KEY OFF» (extractable key). 02_08 Stand (02_09) Centre stand Push with your foot on the centre stand's fork «F» while lifting the vehicle backward, holding onto the handlebar. Stand (02_09, 02_10) Side stand Push with your foot on the stand's prong «L» until it releases into position, while lowering the vehicle onto the stand.
2 Use CAUTION DUE TO THE HIGH TEMPERATURES THE CATALYTIC CONVERTER CAN REACH, ALWAYS TAKE CARE, WHEN PARKING THE SCOOTER, THAT THE EXHAUST DOES NOT COME INTO CONTACT WITH FLAMMABLE MATERIALS, TO AVOID SERIOUS BURNS. CAUTION DO NOT SWITCH OFF THE ENGINE WHILE THE VEHICLE IS MOVING. UNBURNED FUEL COULD ENTER THE CATALYTIC CONVERTER AND BURN, CAUSING IT TO OVERHEAT AND POSSIBLY DESTROYING IT.
Safe driving Some simple tips are provided below that will enable you to use your scooter on a daily basis in greater safety and peace of mind. Your skill and your mechanical knowledge are the basis of a safe ride. We recommend trying out the vehicle in traffic - free zones, in order to acquire a good knowledge of the vehicle it self. 1. Before riding off, remember to put on your helmet and fasten it correctly. 2.Reduce speed on rough roads and ride with care. 3.
CAUTION DO NOT ADJUST THE MIRRORS WHILE RIDING. THIS COULD CAUSE YOU TO LOOSE CONTROL OF THE VEHICLE. CAUTION ANY CHANGES TO THE VEHICLE PERFORMANCE AS WELL AS ALTERATIONS TO ORIGINAL STRUCTURAL PARTS IS STRICTLY FORBIDDEN BY LAW, AND RENDERS THE VEHICLE NO LONGER CONFORMING TO THE APPROVED TYPE AND DANGEROUS FOR RIDING. Accessories (02_12, 02_13) The saddle is supplied with a protection cover. Lift the saddle and extract the cover from its housing to use it.
CAUTION DO NOT USE THE VEHICLE WITHOUT THE PROTECTION COVER.
Beverly 500 Chap.
Engine oil level In 4-stroke engines, engine oil is used to lubricate the distribution elements, the bushes and the thermal group. An insufficient quantity of oil can cause serious damage to the engine.In all four-stroke engines, a loss of efficiency in oil performance and consumption should be considered normal. Consumption can particularly reflect the conditions of use (i.e. when driving at "full acceleration" all the time, oil consumption increases).
If the light comes on during braking, at idling speed or while turning a corner, it is necessary to check the oil level and top up if required. If, after having topped up the oil, the warning light persists in coming on while braking, at idling speed or while turning a corner, it will be necessary to turn to an Authorised Piaggio service centre. Engine oil change (03_03, 03_04) 03_04 The engine oil and filter must be replaced every 6,000 km by an authorised Piaggio service centre.
CAUTION USED OILS CONTAIN SUBSTANCES HARMFUL TO THE ENVIRONMENT. FOR OIL REPLACEMENT, CONTACT AN AUTHORISED SERVICE CENTRE, WHICH IS EQUIPPED TO DISPOSE OF USED OILS IN AN ENVIRONMENTALLY FRIENDLY AND LEGAL WAY. Recommended products AGIP CITY HI TEC 4T Engine oil SAE 5W-40, API SL, ACEA A3, JASO MA Synthetic oil Characteristic Engine oil (at oil and filter change) 1.5 lt. Hub oil level (03_05) Check the oil in the rear hub. To check the rear hub oil level, proceed as follows: 1.
CAUTION RIDING THE VEHICLE WITH INSUFFICIENT HUB LUBRICATION OR WITH CONTAMINATED OR IMPROPER LUBRICANTS ACCELERATES THE WEAR AND TEAR OF THE MOVING PARTS AND CAN CAUSE SERIOUS DAMAGE. CAUTION USED OIL CAN HARM THE ENVIRONMENT. COLLECTION AND DISPOSAL SHOULD BE CARRIED OUT IN COMPLIANCE WITH CURRENT REGULATIONS. CAUTION AN EXCESSIVE QUANTITY OF OIL CAN LEAD TO LEAKAGE, WHICH MAY CAUSE THE ENGINE AND THE WHEEL TO GET DIRTY.
CAUTION FOR OIL REPLACEMENT, CONTACT ANY AUTHORISED SERVICE CENTRE AS THEY ARE EQUIPPED TO DISPOSE OF USED OILS IN AN ENVIRONMENTALLY FRIENDLY AND LEGAL WAY. Recommended products AGIP ROTRA 80W-90 Rear hub oil SAE 80W/90 Oil that exceeds the requirements of API GL3 specifications Characteristic Quantity: approx. 250 cc Tyres (03_06) Check periodically (roughly every 500 km) the tyre pressure.
CAUTION IT IS MANDATORY TO ADOPT EXCLUSIVELY "S" CLASS TYRES, WHICH GUARANTEE CORRECT VEHICLE PERFORMANCE AT THE DIFFERENT SCOOTER SPEEDS. USING ANY OTHER TYRE MAY RESULT IN VEHICLE INSTABILITY. IT IS ADVISABLE TO USE TYRE TYPES RECOMMENDED BY PIAGGIO. Characteristic Front tyre pressure 2.2 bar Rear tyre pressure 2.2 bar with driver only Rear tyre pressure 2.3 bar with passenger.
REAR TYRE Rear tyre Pirelli 150/70 14" GTS 24 M/C 66S TUBELESS Spark plug dismantlement (03_07) Proceed as follows: 1. Remove the access cover over the spark plug on the left-hand side of the scooter and reach into the spark plug with your hand. 2. Disconnect spark plug HV wire cap «A» ; 3. Unscrew the spark plug using the spark plug wrench supplied; 03_07 4. When refitting, place the spark plug into the hole at the required angle and tighten by hand until it is finger tight; 5.
Spark plug • • NGK CR7EKB Champion RG6YC Electrode gap 0.7-0.8 mm Removing the air filter (03_08) Proceed as follows: - Loosen the clamping screws and remove the air filter cover "D"; - Remove the filter element and clean it with water and shampoo; then dry it with a clean cloth and slight blows of compressed air. Finally, immerse it in a mixture containing 50% oil of the recommended type and 50% petrol. Then gently squeeze the filter element between your hands, allow it to drip and then refit it.
Recommended products AGIP FILTER OIL Oil for air filter sponge Mineral oil with specific additives for increased adhesiveness Air filter cleaning (03_09, 03_10) Periodically check the exhaust blow-by and condensate pipe in area "E" and empty it into a suitable container. Position the scooter on the centre stand and remove cover "F", without removing any other components, working from underneath the scooter and noting that it is located behind the shoulder of the transmission air intake.
The engine cooling system is of the forced liquid circulation type. The coolant circuit contains approx. 1.7 litres of coolant consisting of a mixture of 50% demineralised water and glycol ethylene-based antifreeze solution with corrosion inhibitors. The liquid supplied with the scooter is already mixed and ready for use. 03_11 For proper functioning of the engine, ensure that the temperature of the coolant remains in the middle zone of gauge "C" on the instrument panel.
N.B. IF DURING A NON-DEMANDING RIDE THE COOLANT WARNING LIGHT COMES ON, SHUT OFF THE ENGINE AND ALLOW IT TO COOL DOWN. THEN CHECK THE COOLANT LEVEL; IF THE LEVEL IS NOT CORRECT, CONTACT AN AUTHORISED SERVICE CENTRE. WARNING TO AVOID THE RISK OF SCALDING, DO NOT UNSCREW THE EXPANSION TANK COVER WHILE THE ENGINE IS STILL HOT. WARNING TO PREVENT AVOID HARMFUL FLUID LEAKAGE WHILE RIDING, ENSURE THAT THE LEVEL NEVER EXCEEDS THE MAXIMUM VALUE. TO ENSURE CORRECT ENGINE OPERATION, KEEP THE RADIATOR GRILLE CLEAN.
Braking system fluid top up (03_16) Proceed as follows: Remove tank cover "D" and loosen the two screws "E" and top up the brake fluid level using only the prescribed brake fluid and without exceeding the maximum level. 03_15 Under normal climatic conditions, the brake fluid should be replaced every 2 years. This operation must be carried out by trained technicians; please contact your nearest PIAGGIO dealer or an authorised service centre.
FMVSS DOT 4 Synthetic fluid Battery (03_17, 03_18) To access the battery, proceed as follows: 1. Place the scooter on its centre stand; 2. Lift the seat, paying attention to the points mentioned above. 3. Remove retainer "A" and cover "B". 4. Release the elastic strap "C". 03_17 The battery is the electrical device that requires the most frequent inspections and diligent maintenance.
Battery 12V - 12 Ah Use of a new battery Ensure that the terminals are connected correctly and check the voltage. CAUTION DO NOT REVERSE THE POLARITY: RISK OF SHORT CIRCUIT AND DAMAGE TO THE ELECTRICAL SYSTEM. Checking the electrolyte level The electrolyte level, which should be checked regularly, must always be at the maximum level. To top it up to this level, use only distilled water.
- At least once a month start the engine and run it slightly above idle speed for 10-15 minutes. This keeps all the engine components, as well as the battery, in good working order. - Take your vehicle to a garage (as indicated in the "Vehicle not used for extended periods" section) to have the battery removed. Have the battery cleaned, charged fully and stored in a dry, ventilated place. Recharge at least once every two months.
MODIFICATIONS OR REPAIRS TO THE ELECTRICAL SYSTEM, PERFORMED INCORRECTLY OR WITHOUT STRICT ATTENTION TO THE TECHNICAL SPECIFICATIONS OF THE SYSTEM, CAN CAUSE ERRORS IN FUNCTIONING AND RISK OF FIRE.
Fuse: 5A Protected circuits: Basic power supply to control unit, immobilizer Control unit live Position on fuse box: 4 Fuse: 5A Protected circuits: Control unit live Outlet 12V-180W, button for helmet compartment lighting, bulb for helmet compartment lighting, contacts for key switch, actuator for seat opening, electrical button opening Position on fuse box: 5 Light remote control Position on fuse box: 6 Fuse: 15A Protected circuits: Outlet 12V-180W, button for helmet compartment lighting, bulb for he
Position on fuse box: 8 3 Maintenance Stop lights, preparation for radio and anti-theft device, damper, instrument panel live Fuse: 7.5A Protected circuits: Stop lights, preparation for radio and anti-theft device, damper, instrument panel live Light switch, front and rear light bulbs, license plate bulb, instrument panel lighting Position on fuse box: 9 Fuse: 7.
Quantity: 1 Power: 12V - 5W Turn indicator bulbs Type: Spherical Quantity: 4 Power: 12V - 10W Rear tail light bulb Type: All glass Quantity: 2 Power: 12V - 3W Stop light bulb Type: Spherical Quantity: 1 Power: 12V - 10W Instrument panel lighting bulb Type: All glass Quantity: 2 Power: 12V - 2W Helmet compartment light bulb Type: Cylindrical Quantity: 1 3 Maintenance Power: 12V - 5W License plate light bulb Type: All glass Quantity: 1 Power: 12V - 5W 52
To remove the front headlight assembly, proceed as follows: 1. Remove screws «A» of the brake fluid tank cover. 2. Remove the 3 windshield screws and the windshield proper. 3. Remove the rear-view mirrors. 4. Remove the screws "C" of the upper coupling. 03_22 5. Remove the screws "C" of the lower coupling. 6. Remove the two screws "D" of the front handlebar cover. 7. Remove the front handlebar cover. This gives access to the bulbs.
2. Turn on the headlight and check that the borderline of the projected light beam on the screen is not higher than 9/10 or lower than 7/10 of the distance from the ground to the centre of vehicle headlamp; 3. If this is not the case, regulate the headlight by turning screw «A». N.B. THE ABOVE PROCEDURE COMPLIES WITH THE EUROPEAN STANDARDS REGARDING MAXIMUM AND MINIMUM HEIGHT OF LIGHT BEAMS. REFER TO THE STATUTORY REGULATIONS IN FORCE IN EVERY COUNTRY WHERE THE vehicle IS USED.
3 Maintenance 03_28 Front direction indicators (03_29) To replace the burnt bulb, remove the screws «G» 03_29 Rear optical unit (03_30, 03_31, 03_32, 03_33, 03_34) To remove the rear light assembly, proceed as follows: 1. Remove the plastic cover "A" from the rear luggage rack, then remove the two lateral screws of the lower part of the luggage rack proper. 2. Remove screw "B" 3. Remove screws "C" and the lateral panels of the side, paying attention not to damage the retaining straps. 03_30 4.
You thus gain access to the rear light bulb "E", the stop light bulb "F" and turn indicator bulbs "G". Release the spring and take out the bulbs. To replace the rear light bulbs "E", pull out the rubber lamp holder from its seat. To reassemble, repeat the operation in the reverse order.
3 Maintenance 03_34 Number plate light Remove the support of the license plate light by loosening its retaining screw. Take out the rubber lamp holder and then take out the bulb. Helmet compartment lighting bulb Open the helmet compartment, take out the snap-on transparent glass and replace the bulb. Rear-view mirrors Adjust the mirrors by applying slight pressure to the side of the mirror to move it to the desired position.
Front and rear disc brake (03_35) The brake disc and pad wear is automatically compensated, therefore it has no effect on the functioning of the front and rear brakes. For this reason it is not necessary to adjust the brakes. An excessively elastic brake lever stroke may indicate the presence of air in the braking circuit or a failure in the braking system.
Puncture The vehicle is equipped with Tubeless tyres (without inner tube). In the event of a puncture, contrary to the situation with a tyre with inner tube, the tyre deflates more slowly, resulting in a greater steering safety. In the event of a puncture, it is admissible to make an emergency repair using an "inflate and repair" spray can. For a final repair, take your vehicle to an Authorised Service Centre or Dealer. The replacement of a tyre involves removing the wheel in question.
Periods of inactivity (03_36) We recommend carrying out the following operations: 1. Clean the scooter thoroughly and then cover it with a canvas; 2. With the engine off and the piston in the bottom dead centre position, remove the spark plug, and pour into its hole 1 t0 2 cc of the recommended oil. Operate the starter button 1-2 times for roughly 1 second to turn the engine over slowly, then insert the spark plug again; 03_36 3.
THE USE OF A HIGH-PRESSURE WATER JET IS STRONGLY DISCOURAGED FOR ANY ENGINE CLEANING OPERATION; HOWEVER, IF NO OTHER MEANS ARE AVAILABLE, IT IS THEN NECESSARY TO: • ONLY USE THE FAN JET. • DO NOT PLACE THE NOZZLE CLOSER THAN 60 CM. • DO NOT USE WATER AT TEMPERATURES OVER 40ºC. • DO NOT USE HIGH-PRESSURE WATER JETS. • DO NOT STEAM WASH. • DO NOT DIRECT THE JET AT: THE CARBURETTOR, THE ELECTRIC CABLES, THE SLOT DIFFUSERS IN THE TRANSMISSION COVER AND THE SCROLL COVER.
IN ORDER TO MAINTAIN PROPER CLEANING AND BRILLIANCE OF THE MUFFLER, WE RECOMMEND THE USE OF A PRODUCT SPECIFICALLY FOR CHROME-PLATED SURFACES PIAGGIO RECOMMENDS AND DISTRIBUTES A PASTE SPECIALLY FOR THE GLOSS OF STAINLESS STEEL MUFFLERS; IT CAN BE ORDERED UNDER THE NUMBER 602683M FROM THE DEALER NETWORK. STARTING FAILURE Emergency switch in «OFF» Set the switch back to «ON» Fuse blown Replace the blown fuse and have the vehicle checked by an Authorised Service Centre.
3 Maintenance * IMPORTANT: DO NOT USE THE SCOOTER TO THE COMPLETE EXHAUSTION OF THE FUEL; IN THE EVENT THAT THIS SHOULD OCCUR, DO NOT ATTEMPT TO START THE ENGINE. TURN THE KEY SWITCH TO "OFF" AND TOP-UP THE TANK AS SOON AS POSSIBLE. THE FAILURE TO FOLLOW THESE GUIDELINES COULD CAUSE DAMAGE TO THE FUEL PUMP AND/OR THE CATALYTIC CONVERTER. IGNITION PROBLEM Faulty spark plug Contact an Authorised Service Centre. Faulty ignition / injection control Contact an Authorised Service unit.
INSUFFICIENT BRAKING Greasy disc. Worn pads. Faulty Contact an Authorised Service braking system. Presence of air in Centre. the front and rear brake circuit. INEFFICIENT SUSPENSIONS Shock absorber fault, oil leak, end Contact an Authorised Service buffer damaged; shock absorber Centre. preloading incorrectly set IRREGULAR AUTOMATIC TRANSMISSION Contact an Authorised Service Centre.
Beverly 500 Chap.
4 Technical data 04_01 66
4 Technical data DATA Version 500 Engine Single-cylinder, four-stroke, four valves, single overhead camshaft, chain driven on the flywheel side Bore x stroke 92 X 69 mm Cubic capacity 460 cm³ Compression ratio 10.5: 1 Ignition advance (before TDC) Variable advance controlled by the injection control unit Fuel supply 38 Ø mm throttle body and single injector Spark plug • • NGK CR7EKB Champion RG6YC Max. speed 160 km/h Valve clearance intake: 0.15 mm discharge (when cold): 0.
4 Technical data Fuel supply Electronic injection with electric fuel pump. Exhaust muffler absorption-type exhaust muffler with catalytic converter. Electronic ignition inductive, high efficiency integrated with the injection system, with variable timing and separate HV coil. Lubrication Engine lubrication with trochoidal pump (inside the crankcase), oil filter and pressure adjustment bypass. Cooling Forced fluid circulation, with engine driven pump; 3-way thermostat to pump intake.
Pirelli 110/70 16" GTS 23 M/C 52S TUBELESS Rear tyre Pirelli 150/70 14" GTS 24 M/C 66S TUBELESS Front suspension Hydraulic telescopic fork with stem diameter 41 mm. Rear suspension engine in relation to the rocker forks with two double-acting hydraulic shock absorbers and setting of the preload in 4 positions. Chassis Tubular and steel sheets. Empty weight 193 Kg Maximum load Maximum load 189 Kg. Fuel tank capacity ~13,2 l (approximate value) Reserve approx.
4 Technical data
Beverly 500 Chap.
Warnings (05_01) WARNING IT IS ALSO RECOMMENDED THAT "ORIGINAL PIAGGIO SPARE PARTS" BE USED, AS THESE ARE THE ONLY ONES OFFERING YOU THE SAME QUALITY GUARANTEE AS THOSE INITIALLY FITTED ON THE SCOOTER. THE USE OF NON-ORIGINAL SPARE PARTS RENDERS THE WARRANTY VOID. 05_01 WARNING PIAGGIO MARKETS ITS OWN LINE OF ACCESSORIES THAT ARE RECOGNISED AND GUARANTEED FOR USE. IT IS THEREFORE ESSENTIAL, IN ORDER TO CHOOSE AND MOUNT THE ACCESSORIES CORRECTLY, TO CONTACT AN AUTHORISED DEALER OR SERVICE CENTRE.
5 Spare parts and accessories ANCE, AS WELL AS DECREASE THE LEVEL OF SAFETY DURING USE. NEVER RIDE THE SCOOTER WITH ADDED ACCESSORIES FASTER THAN 130 Km/h. THIS MAXIMUM SPEED LIMIT CAN BE FURTHER REDUCED DUE TO THE USE OF NON-PIAGGIO ACCESSORIES, AN ABNORMAL LOAD, WORN TYRES, AND SCOOTER, STREET AND WEATHER GENERAL CONDITIONS.
5 Spare parts and accessories
Beverly 500 Chap.
Scheduled maintenance table Adequate maintenance is fundamental to ensuring long-lasting, optimum operation and performance of your scooter. For this purpose, PIAGGIO has developed a series of checks and maintenance operations (against payment) that are contained in the summary table shown on the next page. Any minor faults should be reported without delay to a PIAGGIO Dealer or Authorised Service Centre without waiting until the next scheduled service.
6 Programmed maintenance Tyre pressure and wear - check Vehicle and brake test - test ride Hub oil - change Crankcase breather - empty Steering - adjustment Injection system pipework - visual check AFTER 10,000 KM AFTER 30,000 KM AFTER 50,000 KM AND AFTER 70,000 KM Safety locks - check Spark plug - replacement Driving belt - replacement Throttle lever - adjustment Air filter - check Air filter belt compartment - check Engine oil - change Valve clearance - check Electrical system and battery - check Coolan
Tyre pressure and wear - check Vehicle and brake test - test ride Hub oil - check Stand control roller - replace Suspensions - check Steering - Check Injection system pipework - visual check Crankcase breather - empty AFTER 20,000 KM AFTER 40,000 KM AFTER 60,000 KM AND AFTER 80,000 KM Safety locks - check Bushing of driven pulley Spark plug - replacement 6 Programmed maintenance Driving belt - replacement Throttle lever - adjustment Air filter - check Air filter belt compartment - check Engine oil - chan
6 Programmed maintenance Engine oil - replacement Brake pads - check condition and wear Sliding block / variable speed rollers - change Tyre pressure and wear - check Vehicle and brake test - test ride Hub oil - check Stand control roller - replace Crankcase breather - empty Suspensions - check Steering - Check Injection system pipework - visual check Fuel filter - check RECOMMENDED PRODUCTS TABLE Product Description Specifications AGIP ROTRA 80W-90 Rear hub oil SAE 80W/90 Oil that exceeds the requir
Product Description Specifications Oil for air filter sponge Mineral oil with specific additives for increased adhesiveness AUTOSOL METAL POLISH Muffler cleaning paste Specific product for cleaning and polishing stainless steel mufflers.
Description Specifications between -20 C and +120 C; NLGI 2; ISO-LXBCIB2. Selènia Moto Rider (06_01) PIAGGIO-GILERA rides with SELENIA MOTO RIDER The technology and quality of FL Selenia for a range of high performance products. Thanks to the co-operation between FL Selenia and Piaggio Engineering, the Selenia Moto Rider products give the Piaggio/Gilera scooters protection and safety in every operating situation.
6 Programmed maintenance
TABLE OF CONTENTS A F L Air filter: 41, 42 Fuel: 15 Fuses: 48 Light switch: 11 B Battery: 46, 47 Brake: 44, 58 M H Maintenance: 33, 75, 76 Headlight: 53 Horn: 11 Hub oil: 36 Mirrors: 57 C S Clock: 9 Saddle: 18 Scheduled maintenance: 76 Shock absorbers: 25 Spark plug: 40 Stand: 28 Start-up: 11 I Disc brake: 58 Identification: 17 Immobilizer: 12, 14 Instrument panel: 8 E K Engine oil: 34, 35 Engine stop: 12 Key switch: 10 Keys: 12 D T Tank: 15 Technical Data: 65 Top box: 18 Transmission
The descriptions and illustrations given in this publication are not binding. While the basic specifications as described and illustrated in this booklet remain unchanged, PIAGGIO-GILERA reserves the right, at any time and without being required to update this publication beforehand, to make any changes to components, parts or accessories, which it considers necessary to improve the product or which are required for manufacturing or construction reasons.