Owner's Manual
Table Of Contents
- Quick Start Guide
- Operation Manual
- Reset
- Demo Mode (Menu Item)
- Table of Contents
- Parking Brake Interlock
- Using This Manual
- Parts & Controls
- Basic Operation
- Using the Navigation Menu Screens
- Displaying Rear View Camera Input
- Using the Map
- Customizing the Map Screen Settings
- Setting a Route to Your Destination
- Checking and Modifying the Current Route
- Advanced Operation
- Searching for and Selecting a Location
- Registering and Editing Locations
- Browsing Information on MSN Direct
- Registering and Connecting the Bluetooth Device
- Using Hands-Free Phoning
- Using the Radio
- HD Radio
- Playing Audio CDs
- Playing Music Files on ROM
- Playing a DVD-Video
- Playing a DVD-VR Disc
- Playing a DivX Video
- DVD-Video, DVD-VR, DivX Setup
- Playing Music Files (from USB or SD)
- Using an iPod
- Bluetooth Audio Player
- Using the XM Tuner
- Using the SIRIUS Tuner
- Using AV Input
- External Input
- Selecting the Video for Rear Display
- Picture Adjustments
- Customizing Preferences
- Navigation Settings Menu
- System Settings Menu
- Navigating the Menus
- Selecting the Language
- Setting the Time Difference
- Changing the Unit Between Kilometers and Miles
- Changing the Virtual Speed of the Vehicle
- Setting the Volume for Guidance and Phone
- Changing the Splash Screen
- Setting the Rear View Camera
- Touch Panel Calibration
- Illumination Color
- Checking the Version Information
- Replicating the Settings
- Turning Off the Screen
- AV Sound Settings Menu
- AV System Settings Menu
- Navigating the Menus
- Setting Video Input 1 (AV1)
- Setting Video Input 2 (AV2)
- Switching the Auto Antenna Setting
- Changing the Wide Screen Mode
- Setting the Rear Output
- Switching the Sound Muting / Attenuation
- Changing the Voice Output of the Navigation Guidance
- Acquiring / Cataloging iPod Music Information
- Displaying your DivX VOD Registration Code
- Operating the Navigation System by Voice
- Anti-Theft Function
- Additional Information
- Troubleshooting
- Error Messages
- Glossary
- Specs
- Installation Manual
- Table of Contents
- Note for Blue Wire
- Installation Hardware
- System Connections
- Power / Speaker Connections
- Speed Signal Connection
- Parking Brake Connection
- Reverse Gear Signal Connection
- Pre Amp Connection
- Rear View Camera Connection
- Connecting a Rear Display
- External Video Input Connections
- Mounting
- Installing the GPS Antenna
- Installing the Microphone
- Note on Voice Recognition Control
- Warranty
CAUTION
For safety reasons, these route-setting functions
are not available while your vehicle is in motion.
To enable these functions, you must stop in a
safe place and put on the parking brake before
setting your route.
p Some information regarding traffic regula-
tions depends on the time when the route
calculation is performed. Thus, the infor-
mation may not correspond with a certain
traffic regulation when your vehicle actually
passes through the location in question.
Also, the information on the traffic regula-
tions provided will be for a passenger vehi-
cle, and not for a truck or other delivery
vehicles. Always follow the actual traffic
regulations when driving.
The basic flow of creating
your route
1 Park your vehicle in a safe place, and
apply the parking brake.
2 Display the “Top Menu” screen.
3 Select the method of searching for your
destination.
= For details, refer to Chapter 8.
4 Enter the information about your desti-
nation to calculate route.
5 Confirm the location on the map.
= For details, refer to Checking the location on
the map on this page.
6 The navigation system calculates the
route to your destination, and then shows
the route on the map.
7 Check and decide the route.
= For details, refer to Checking the calculated
route on this page.
8 Your navigation system sets the route
to your destination, and the map of your
surroundings appears.
9 After releasing the parking brake, drive
in accordance with navigation guidance.
Checking the location on
the map
After searching for the destination, the “Loca-
tion confirmation screen” appears.
Location confirmation screen
% Touch [OK].
The destination is set, and then route calcula-
tion starts.
p If you press MODE button during route cal-
culation, the calculation is canceled and
the map display appears.
# Touch [Scroll].
The map display changes to the scroll mode. You
can fine-tune the location in the scroll mode, and
then you can set the location as your destination
or do various operations.
# Touch [Waypoint].
The location is added to the “Waypoints List”
screen.
p If a destination is not set, [Waypoint] is not
available.
Checking the calculated route
After the destination is set, route calculation
starts.
Setting a route to your de stination
En
48
Chapter
06