English Operating Instructions Thank you very much for purchasing this PIONEER product. Before using your Plasma Display, please carefully read the “Important Information” and these “Operating Instructions” so you will know how to operate the Plasma Display properly. Keep this manual in a safe place. You will find it useful in the future. Notes on Installation Work: This product is marketed assuming that it is installed by qualified personnel with enough skill and competence.
Warnings and Safety Precaution Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference. This plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Please see the section “Plasma monitor cleaning procedure” on the next page. The plasma display panel consists of fine picture elements (cells) with more than 99.99 percent active cells.
This Class B digital apparatus complies with Canadian ICES-003. 8. Caution This model is for use with the following optional accessories. Use with other optional accessories is capable of resulting in instability causing possible injury. 9. Table top stand: PDK-1014 Wall mount unit: PDK-WM03 10. 11. 12. 13. Important Information 14. 15. DECLARATION OF CONFORMITY This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
English Installation ...................................................... 2 Ventilation Requirements for enclosure mounting .......... 2 How to use the safety metal fittings and the screws for safety metal fittings ................................................ 2 Cable Management .................................................. 3 How to use the remote control .................................... 3 Battery Installation and Replacement ........................... 3 Operating Range .....................
You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. * Do not touch or hold the screen face when carrying the unit. • This device cannot be installed on its own. Be sure to use a stand or original mounting unit.
Part Names and Function Part Names and Function A AC IN Connect the included power cord here. q Power ( ) Turns the monitor’s power on and off. w Remote sensor window Receives the signals from the remote control. e STANDBY/ON indicator When the power is on ............................. Lights green. When the power is in the standby mode ... Lights red. r INPUT/EXIT Switches the input. The available inputs depend on the setting of “BNC INPUT” and “RGB SELECT”.
6 En q POWER ON/STANDBY Switches the power on/standby. (This does not operate when STANDBY/ON indicator of the main unit is off.) w OFF TIMER Activates the off timer for the unit. e DISPLAY Displays the source settings on the screen. r SCREEN SIZE Automatically detects the signal and sets the aspect ratio. SCREEN SIZE button is not active for all signals. t MENU/SET Press this button to access the OSD controls. Press this button during the display of the main menu to go to the sub menu.
English SCREEN SIZE Operation (manual) With this function, you can select one of six screen sizes. When viewing videos or digital video discs 1. Press the SCREEN SIZE button on the remote control. 2. Within 3 seconds ... Press the SCREEN SIZE button again. The screen size switches as follows: The picture is expanded in the horizontal and vertical direction, maintaining the original proportions. * Use this for theater size (wide) movies, etc. 2.35:1 size screen → 4:3 → FULL → WIDE → ZOOM → 2.
* A PC-input picture may not be displayed in these modes, depending on the input signal specifications. 1. Press the button to select a screen mode from among single mode, side-by-side, and picture-in-picture. Operations in the Side-by-side mode To change the picture size, press the cursor button. VIDEO1 A PC2-BNC To move the position of the sub screen, press the cursor or button.
Setting the language for the menus The following describes how to use the menus and the selected items. 1. Press the MENU/SET button on the remote control to display the MAIN MENU. The menu display can be set to one of seven languages. Example: Setting the menu display to “DEUTSCH” MAIN MENU PICTURE SET UP SOUND FUNCTION SCREEN SEL. SIGNAL INFO. MENU OK EXIT EXIT 2. Press the cursor buttons ▲ ▼ on the remote control to highlight the menu you wish to enter. 3.
Sub menu 2 FUNCTION POWER MGT. INPUT SKIP SUB. P DETECT ZOOM NAV PICTURE FREEZE LONG LIFE ON←→OFF ON←→OFF AUTO←→OFF OFF←→S BY S←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT OFF←→S BY S1←→S BY S2←→BTM LEFT←→BTM RIGHT←→TOP RIGHT←→TOP LEFT MANUAL/AUTO ABL 100/75/50/25 ORBITER OFF/AUTO1/AUTO2 INVERSE/WHITE OFF/INVERSE/WHITE SCREEN WIPER ON/OFF SOFT FOCUS OFF/LEVEL1-4 OSD ORBITER ON/OFF OSD CONTRAST LOW/NORMAL Main menu Sub menu Sub menu 2 SIGNAL INFO.
On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”. On “GAMMA” of “PICTURE” menu, select “2.3”. PICTURE PICTURE MEMORY : OFF CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT DNR : LOW COLOR TEMP. : HIGH GAMMA : 2.1 LOW TONE : AUTO SET UP LEVEL : 0 COLOR MGT PURECINEMA : ON AV SELECTION : DYNAMIC EXIT RETURN SEL. ADJ. PICTURE PICTURE MEMORY : OFF CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT DNR : LOW COLOR TEMP. : MIDDLE GAMMA : 2.
SET UP Settings Menu Adjusting the treble, bass and left/right balance and audio input select The treble, bass and left/right balance can be adjusted to suit your tastes. Example: Adjusting the bass Adjusting the Position, Size, PHASE, CLOCK The position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position in the normal mode Setting the BNC connectors Select whether to set the input of the 5 BNC connectors to RGB and component.
Setting the black level for HDMI signal Set the black level for the signal transmitted via the HDMI terminal. Example: Setting “COLOR2” On “HDMI SET UP” of “SET UP” menu, select “COLOR2”. SET UP LANGUAGE : ENGLISH BNC INPUT : COMPONENT D-SUB INPUT : RGB HD SELECT : 1080 I RGB SELECT : AUTO HDMI SET UP : COLOR2 COLOR SYSTEM : AUTO BACK GROUND : GRAY SIDE MASK : 3 S1/S2 : OFF DISPLAY OSD : ON OSD ADJUST : TOP LEFT ALL RESET : OFF SEL. ADJ.
On “POWER MGT.” of “FUNCTION” menu, select “ON”. On “INPUT SKIP” of “FUNCTION” menu, select “ON”. FUNCTION POWER MGT. : OFF INPUT SKIP : ON SUB. P DETECT : AUTO ZOOM NAV : BTM LEFT PICTURE FREEZE : S BY S1 LONG LIFE : MANUAL SEL. ADJ. EXIT RETURN OSD (On Screen Display) Controls FUNCTION POWER MGT. : ON INPUT SKIP : OFF SUB. P DETECT : AUTO ZOOM NAV : BTM LEFT PICTURE FREEZE : S BY S1 LONG LIFE : MANUAL SEL. ADJ.
ABL (Auto Brightness Limiter) Use this to activate the brightness limiter. Example: Setting “ABL” to “75” On “ABL” of “LONG LIFE” menu, select “75”. OSD (On Screen Display) Controls LONG LIFE ABL : 75 ORBITER : OFF INVERSE/WHITE : OFF SCREEN WIPER : OFF SOFT FOCUS : OFF OSD ORBITER : ON OSD CONTRAST : LOW SEL. ADJ. EXIT RETURN Information ABL settings 100: The brightness of the screen is adjusted automatically to suit the picture quality. 75, 50, 25: Sets maximum brightness.
Table of Signals Supported mini D-Sub 15-pin connector (Analog) Supported resolution 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 Computer input signals supported by this system Model Dots lines Signal Type 640 400 640 480 Pin No.
If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service. Symptom Mechanical sound is heard. The unit emits a crackling sound. Picture is disturbed. Sound is noisy. Remote control operates erroneously. The remote control does not work. Monitor’s power does not turn on when the remote control’s power button is pressed.
Specifications English Screen Size Aspect Ratio Resolution Signals Synchronization Range Input Signals Specifications Input Terminals PC Visual 1 (Analog) Visual 2 (Analog) Video Visual 1 Visual 2 Visual 3 COMPONENT Visual 1 Visual 2 HDMI Audio RS-232C Sound output Power Supply Current Rating Power Consumption Dimensions 30 En 53.2"(H) 29.9"(V) inches 1351(H) 760(V) mm diagonal 61" 16 : 9 1365(H) 768(V) pixels Horizontal : 15.8 to 110 kHz (automatic : step scan) Vertical : 59.