64-bit PCI Gigabit Ethernet Network Adapter ENW-9607/9607M User’s Manual Version 1.
Copyright Copyright 2004 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
Table of Contents CHAPTER 1 INTRODUCTION ............................................................................................. 1 1.1 PACKAGE CONTENT .......................................................................................................................... 1 1.2 FEATURES ........................................................................................................................................ 1 1.3 VERIFYING YOUR SYSTEM REQUIREMENTS .....................................
Chapter 1 Introduction The ENW-9607 is a 64-bit 10/100/1000Base-T PCI 2.2 Gigabit Ethernet adapter designed to address high-performance system application requirements. The ENW-9607M provides a SFP, mini-GBIC interface. It can be attached with 1000Base-SX or 1000Base-LX mini-GBIC modules, depending on the practical applications. Using PCI 2.
1.3 Verifying Your System Requirements Before installing the ENW-9607/9607M, be sure your computer meets the following requirements: Hardware ü CPU: 300MHz or Faster ü RAM: 64MB (Minimum) ü PCI Local Bus 2.1 or 2.2 compliant Software ü Microsoft Windows 98/Me/NT/2000/XP/Server 2003 ü Linux ü Novell 4.x / 5.x / 6.x 1.
Chapter 2 Hardware Installation 2.1 LED definitions The faceplate of ENW-9607 has four LEDs: 100, 1000 FDX and ACT. And ENW-9607M has three LEDs: 1000, FDX and ACT. The pictures below have showed the faceplate of ENW-9607 and ENW-9607M. Table 2-1 and 2-2 explain the function and state of the LEDs.
LED Description Off/Off: Works with 10Mbps 100 / 1000 On/Off: Works with 100Mbps Off/On: Works with 1000Mbps Off: Works in Half-Duplex mode FDX On: Works in Full-Duplex mode ACT Blink: Transmitting or receiving data through the LAN Table 2-1 Descriptions of ENW-9607 LEDs LED Description Off: The connection is not established. 1000 On: The connection is not established.
Step 7: Replace the PC cover. Step 8: Power on the PC and refer to next chapter to install the driver of this adapter. ? Note: Please do not install the ENW-9607/9607M in a shared PCI slot. Avoid any PCI slot next to an ISA slot because this is often a shared slot and does not support bus mastering. You may refer to the mainboard manual to know which PCI slot share the resource with AGP slot and avoid using it as well.
Chapter 3 Driver Installation A device driver must be installed before your ENW-9607/9607M can be used with your computer. This chapter describes how to install the driver for various operating systems. Before you begin the driver installation process, make sure you have the installation disks for your computer ’s operation system nearby. The driver installation below is for ENW-9607M, which is similar for ENW-9607.
5. Select “Specify a location” and click “Next”. 6. You can click “Browse” to specify the driver location. (Assume "E" is your CD-ROM drive, the driver can be found in E:\Drivers\ENW-9607M\Win2000). Please click “OK” to continue. 7. Windows will show this screen to prompt you that it finds a driver for the device you are installing, please click “Next” to continue. 8. Windows may prompt you this driver is not digitally signed by Microsoft. If the device name is correct, please press ”Yes” to continue.
9. Please click “Finish” to complete the driver installation. (In Win98/Me, Windows will ask you restart your PC when driver installation finished.) 3.2 Installing Driver To Windows XP / Server 2003 ? The following installation operates under Window XP. Procedures will be similar Note: to Window Server 2003. 1. Install ENW-9607M into your PC’s PCI slot. 2. Power on the PC and insert Driver Disk into CD-ROM drive. 3. Windows XP will detect ENW-9607M and ask you to install driver.
4. Please select “Include this location in the search” and then click “Browse” to specify ENW-9607M driver location to install. (Assume "E" is your CD-ROM drive, you can find ENW-9607M driver in E:\Drivers\ENW-9607M\WinXP). Please click “Next” to continue. 5. WinXP will show you this dialog box to prompt you the driver is not digitally signed by Microsoft, please press “Continue Anyway” to continue. 6. Please click “Finish” to complete the driver installation.
3.3 Installing Driver To Windows NT 1. Install ENW-9607M into your PC’s PCI slot. 2. Power on the PC and insert Driver Disk into CD-ROM drive. 3. Click START -> SETTINGS -> CONTROL PANEL -> NETWORK. 4. Select ADAPTERS. 5. Click “ADD” button. 6. Select “HAVE DISK”. 7. Assume "E" is the CD-ROM drive. Enter the path as “E:\Drivers\ENW-9607M\WinNT. 8. Click OK. 9. Select the “PLANET ENW-9607M 1000Base-SX/LX SFP Gigabit Ethernet Adapter (Marvell Chip)” entry that matches your adapter. 10.
and start the build process with the following command: # cd DriverInstall # ./install.sh 4. Choose your favorite installation method. 5. The driver will be compiled and installed. 6. Please restart Linux system. 3.5 Installing Driver To Novell 4.x 1. Update NBI.NLM, NEB.NLM, MSM.NLM, and ETHERTSM.NLM in the SYSTEM directory of the server to the latest versions available for NetWare 4.20 (working versions are provided with this driver). 2.
Chapter 4 Utility ENW-9607 is VCT Technology supported. The Virtual Cable Tester(TM) installation package contains the Marvell Virtual Cable Tester(TM) application. This utility can help user to diagnose the cable status and verify the cable length. ? The Marvell Virtual Cable Tester(TM) can only be used on Windows 2000 and Note: Windows XP. 4.1 Installation Instructions 1. Run “setupVCT.exe” under “E:\Utility\VCT” directory.
3. Please check the installation note and click “Next” to continue. 4. Please click “Install” to begin the installation. 5. Please click “Finish” to complete the utility installation. 4.2 Utility Operating After installation, you can find the utility in “Start” => “Programs” => “Marvell” => “Virtual Cable Tester”. Please click “Virtual Cable Tester” option to start. If you see the dialog box as below, please make sure you are using ENW-9607 and the card had been install to your PC properly.
your PC, please select the card you want to test in the first field. Then click “Run” button to test the cable status of selected ENW-9607.
Chapter 5 Model ENW-9607 Specifications ENW-9607M IEEE 802.3 Standards IEEE 802.3u IEEE802.3ab IEEE802.3ab Connectors RJ-45 Mini-GBIC LEDs 100 / 1000 / FDX / ACT 1000 / FDX / ACT 4-pair, Category 5 Depends Category 5 enhanced module installed on the mini-GBIC Cabling Requirements Half duplex mode: 10/100/1000 Mbps Speed Full duplex mode: 2000 Mbps Full duplex mode: 20/200/2000 Mbps Bus Type PCI 2.1/ 2.
Appendix A Advanced Properties The default settings of the adapter should work in most cases. However, if you experience any unusual circumstances during your installation, these settings may help you to trouble shoot the adapter. Do not change any of these settings without a thorough understanding on your network. The following table briefly explains the function of each property. Parameter Description Value The IEEE 802.
