000BASE-X to 10/100/1000BASE-T 802.
Trademarks Copyright © PLANET Technology Corp. 2016. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners.
FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications.
WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 1000BASE-X to 10/100/1000BASE-T 802.3at PoE+ Media Converter User’s Manual For Model: GTP-805A Rev 1.
Table of Contents 1. Overview.......................................................................... 6 2. Checklist........................................................................... 7 3. Product Outlook................................................................. 8 4. Link Fault Passthrough (LFP)............................................. 10 5. Installing the Converter.................................................... 13 6. PoE Function....................................................
1. Overview Thank you for purchasing PLANET GTP-805A 1000BASE-X Fiberoptic to 10/100/1000Mbps Ethernet twisted-pair 802.3at PoE Bridge Converter. This converter is used to convert one type of media signal to other type that allows two segments to connect easily, efficiently and inexpensively. The converter provides Power over Ethernet power injector function which is able to drive one IEEE 802.3at/802.3af compliant powered device. About the Power over Ethernet Injector The GTP-805A is an IEEE 802.3at/802.
2. Checklist Your GTP-805A box should contain the following items: ll 1000BASE-X to Converter x 1 10/100/1000BASE-T 802.3at PoE Media ll User’s Manual x 1 ll AC-DC Adapter (Input: 54V DC, 0.74A max.) x 1 If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
3. Product Outlook Overview The layout of the GTP-805A IEEE 802.3at PoE Media Converter 1000Base-X to 10/100/1000Base-T Power over Ethernet 10/100/1000Base-T 52V~56V DC Mini-GBIC Fiber TX LNK ACT LFP OFF ON PoE Media Converter 1000X to 10/100/1000T PWR PoE In Use Ethernet+DC Figure 3-1: Product Outlook of the GTP-805A Left View There are one RJ45 twisted-pair jack (auto-MDI/MDI-X), one fiber-optic connector (vary by model) and four LED indicators.
Right View There is one DIP switch for Link Fault Passthrough (LFP) feature. It is turned on for LLCF and LLR detection but this feature is not operable when turned off. Please refer to the following sections for more. There is also one DC 52V ~ 56V power socket for the PoE+ Media Converter.
4. Link Fault Passthrough (LFP) The LFP function includes the Link Fault Passthrough function (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alert administrators to the problem of the link media and provide an efficient solution to monitoring the net. The DIP switch’s LFP function can be disabled or enabled. LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter’s fiber will disconnect the transmission link.
If the connection breaks, the GTP-805A that loses the link will forward to the Switch/Hub that generates a trap to the management station. The administrator can then determine the source of the problem. Management Station Switch/Hub w/SNMP Media Converter Media Converter LFP ON l LED lit = established link Management Station LFP ON Broken Fiber Cable TP Switch/Hub w/SNMP TP ° LED unlit = no link * Units are shipped with the LFP function being disabled (OFF).
If one of the optical conductors is down (as shown in the diagram box below), the converter with LLR function will return a no-link condition to its link partner. With LLCF function also enabled, the no-link condition is carried forward to the switch/ hub where a trap is generated to the management station, and the administrator can then determine the source of the loss.
5. Installing the Converter Please follow these steps to install the PoE+ Media converter: ll Turn off the power of the device/station in a network to which the GTP-805A will be attached. ll Ensure that there is no activity in the network. ll Attach fiber cable from the GTP-805A to the fiber network. ll Attach a Cat.5/5e/6 UTP cable from the 10/100/1000BASE-T network to the RJ45 port on the GTP-805A. ll Connect the 52V~56V DC power adapter to the GTP-805A and verify that the Power LED lights up.
6. PoE Function The installation of the GTP-805A and the IEEE 802.3at/802.3af Injector/Splitter Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3at/802.3af devices that need to be powered on, the GTP-805A can provide you a way to supply power for this Ethernet device conveniently and easily. The GTP-805A equips an AC-DC adapter with DC 54V input and it injects the DC power into the pin of the twisted-pair cable (Pins 1, 2, 3 and 6).
For the places hard to find the power inlet, the GTP-805A provides the easiest way to power your Ethernet devices such as PLANET IEEE 802.3at/802.3af Power over Ethernet Splitter (POE-152S/162S) with Internet Camera or PoE Wireless Access Point installed in a wide-range place.
7. LED Indication System LED PWR Color Green Function Light Indicate the device is powered. 10/100/1000BASE-T Port LED LNK/ ACT Color Green Function Blink Indicate that the PoE+ Media Converter is actively sending or receiving data over that port. Light Indicate that the port is link up at 10/100/1000Mbps. Off Light PoE in Use Orange Off Indicate that the port is link down. Indicate that the port is providing DC 54V to remote powered device.
8. Cable Connection Parameter The limitations are as below: Duplex Connection Limitation (max.
9. GTP-805A Technical Specifications The GTP-805A comes with the following standard features: ll Standard: IEEE 802.3/802.3u/802.3ab, 10/100/1000BASE-T and IEEE 802.3at/802.
APPENDIX A A.
Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. A.2 RJ45 Cable Pin Assignment There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
A.3 Fiber Optic Cable Connection Parameter The wiring details are shown below: Fiber Optic Patch Cables: Standard Fiber Type Cable Specification 1000BASE-SX (850nm) Multi-mode 50/125μm or 62.5/125μm Multi-mode 50/125μm or 62.
EC Declaration of Conformity For the following equipment: *Type of Product: *Model Number: 1000Base-SX/LX to 10/100/1000Base-T PoE Media Converter GTP-802、GTP-802S、GTP-805A * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 10F ., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
