Owner's Manual

14
MAINTENANCE SCH E DULE
Check:
Fuel mixture level Before each use....
Bar lubrication Before each use.......
Chain tension Before each use.......
Chain sharpness Before each use.....
For damaged parts Before each use...
For loose caps Before each use......
For loose fasteners Before each use...
For loose parts Before each use......
Inspect and Clean:
Bar Before each use................
Complete saw After each use.......
Air filter Every 5 hours*.............
Chain brake Every 5 hours*.........
Spark arresting screen
and muffler Every 25 hours*..........
Replace spark plug Yearly.
Replace fuel filter Yearly...
* Hours of Operation --
Each hour of operation is approximately
2 tanks of fuel.
AIR F ILTER
CAUTION
: Do not clean filter in gasoline
or other flammable solvent to avoid creating
a fire hazard or producing harmful evapora-
tive emissions.
Cleaning the air filter:
A dirty air filter decreases the life and perfor-
mance of the engine and increases fuel con-
sumption and harmful emissions. Always
clean your air filter after 10 tanks of fuel or 5
hours of operation, whichever comes first.
Clean more frequently in dusty conditions. A
used air filter can never be completely
cleaned. It is advisable to replace your air fil-
ter with a new one after every 50 hours of op-
eration, or annually, whichever comes first.
1. Loosen 3 screws on cylinder cover.
2. Remove cylinder cover.
3. Remove air filter.
4. Clean the air filter using hot soapy water.
Rinse with clean cool water. Air dry
completely before reinstalling.
5. Lightly oil air filter before installing to im-
prove the ef ficiency of air filter . Use
2--cycle engine oil or motor oil (SAE 30).
Squeeze excess oil from filter.
6. Reinstall air filter.
7. Reinstall cylinder cover and 3 screws.
TIghten securely.
Air Filter
Cylinder Co
v
er
Screws
Cylinder
Cover
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
As the unit is used, carbon deposits build up
on the muffler and spark arresting screen,
and must be removed to avoid creating a fire
hazard or af fecting engine performance.
Replace the spark arresting screen if breaks
occur.
Mu
f
f
ler Di
f
f
user
Muffler
Cover
Screws
Muffler
Cover
Muffler
Body
Spark
Arresting
Screen
CLEANING THE SPARK ARREST -
ING SCREEN
Cleaning is required every 25 hours of op-
eration or annually, whichever comes first.
1. Loosen and remove the 2 muffler cover
screws.
2. Remove the muffler cover (cover snaps
off muffler body).
3. Remove muffler diffuser and spark ar-
resting screen assembly. Notice the
orientation of these parts for reassem-
bling.
4. Clean the spark arresting screen with a
wire brush. Replace screen if breaks are
found.
5. Replace any broken or cracked muffler
parts.
6. Reinstall diffuser and spark arresting
screen assembly with round holes fac-
ing up.
7. Reinstall muffler cover and 2 screws.
Tighten securely.
CARBURETOR ADJUSTMENT
WARNING: The chain will be mov-
ing during most of this procedure. Wear your
protective equipment and observe all safety
precautions. The chain must not move at idle
speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if
you notice any of the following conditions:
S Chain moves at idle. See IDLE SPEED--T
adjusting procedure.
S Saw will not idle. See IDLE SPEED--T ad-
justing procedure.
Idle Speed--T
Allow engine to idle. If the chain moves, idle
is too fast. If the engine stalls, idle is too slow.
Adjust speed until engine runs without chain
movement (idle too fast) or stalling (idle too
slow). The idle speed screw is located in the
area above the primer bulb and is labeled T.
S Turn idle speed screw (T) clockwise to in-
crease engine speed.
S Turn idle speed screw (T) counterclock-
wise to decrease engine speed.