PRO Blower Instruction Manual

-- 5 --
S
To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S
To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S
Use rakes and brooms to loosen debris be-
fore blowing.
S
In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
S
Conserve water by using power blower s
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S
Watch out for children, pets, open windows,
or freshly washed cars. Blow debris away
safely.
S
Use the full blower nozzle extension so the
air stream can work close to the ground.
S
After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
FUELING
WARNING:
Remove fuel cap slowly
when refueling.
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good quality
2-cycle air-cooled engine oil. We recommend
Poulan or Poulan Pro brand oil. Mix gasoline
and oil at a ratio of 40:1 (A 40:1 ratio is
obtained by mixing 3.2 ounces of oil with 1
gallon of unleaded gasoline). Do not use
automotive oil or boat oil. These oils will
cause engine damage. When mixing fuel,
follow the instructions printed on the
container. Always read and follow safety
rules under HANDLE FUEL WITH CAUTION
in the safety rules section.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid
engine problems, empty the fuel system
before storage for 30 days or longer. Drain the
gas tank, start the engine and let it run until the
fuel lines and carburetor are empty. Use fresh
fuel next season.
STARTING
TO STOP THE ENGINE
D
To stop the engine, press and hold the ON/
STOP switch in the STOP position until en-
gine comes to a complete stop.
BEFORE STARTING THE ENGINE
You MUST make sure the tubes are secure
before using the unit.
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D
Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
Blower
Vacuum
STARTING POSITION
WARNING:
When starting engine,
hold the unit as illustrated . Do not set unit on any
surface except a clean, hard area when starting
engine or while engine is running. Debr is such
as gravel, sand, dust, grass, etc. could be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
STARTING A COLD ENGINE (or warm
engine that has run out of fuel)
S
Move throttle lever to the
position.
S
Move choke lever to FULL CHOKE.
S
Slowly press the primer bulb 12 times.
Switch
Throttle
Lever
Choke
Lever
Primer
Button
S
Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30
_
F, 8 pulls).
NOTE:
If engine attempts to start before the
5
th
pull, go to next step immediately.
S
Move the choke lever to HALF CHOKE.
S
Pull the starter rope sharply until the engine
runs, but no more than 5 pulls (below 30
_
F,
10 pulls). Run engine for 5 seconds, then
move choke lever to OFF CHOKE.
S
Allow the unit to run for 30 more seconds at
OFF CHOKE before moving the throttle le-
ver to
position.
If engine has not started after 5 pulls (at HALF
CH O KE), repeat ST ARTING A COLD EN G INE
procedure. If engine still does not start, proceed
to STARTING A FLOODED EN GINE.
STARTING A WARM ENGINE
S
Move throttle lever to the
position.
S
Pull starter rope sharply until engine runs,
but no more than 5 pulls.
NOTE
:
If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.