Replacement Part List
Table Of Contents
- PM7500-PM9400E Portable Generator Owner’s Manual
- Table of Contents
- Section 1 Introduction and Safety
- Section 2 General Information and Setup
- Section 3 Operation
- Operation and Use Questions
- Before Starting Engine
- Prepare Generator for Use
- Grounding the Generator When Used as a Portable
- Know Generator Limits
- Transporting/Tipping of the Unit
- Starting Pull Start Engines
- Starting Electric Start Engines (if equipped)
- Low Oil Level Shutdown System
- Charging the Battery (electric start units only)
- Section 4 Maintenance and Troubleshooting
- Part No. A0000061814
- Generador portátil PM7500-PM9400E Manual del propietario
- Índice
- Sección 1 Introducción y seguridad
- Sección 2 Información general y configuración
- Sección 3 Operación
- Preguntas sobre la operación y el uso
- Antes de arrancar el motor
- Preparación del generador para su uso
- Conexión a tierra del generador cuando se utilice como equipo portátil
- Conozca los límites del generador
- Transporte/inclinación de la unidad
- Arranque de motores de arranque retráctil
- Arranque de motores de arranque eléctrico (si están equipados)
- Sistema de cierre por nivel bajo de aceite
- Carga de la batería (solo unidades de arranque eléctrico)
- Sección 4 Mantenimiento y solución de problemas
- N.° de pieza A0000061814
- Génératrice portable PM7500-PM9400E Manuel de l’utilisateur
- Table des matières
- Section 1 Introduction et sécurité
- Section 2 Généralités et configuration
- Section 3 Fonctionnement
- Questions concernant le fonctionnement et l’utilisation
- Avant de démarrer le moteur
- Préparer la génératrice à l’utilisation
- Mise à la terre de la génératrice lors d’une utilisation portable
- Connaître les limites de la génératrice
- Transport et inclinaison de la machine
- Démarrer un moteur à lanceur à rappel
- Démarrer un moteur à démarreur électrique
- Système d’arrêt en cas de faible niveau d’huile
- Recharger la batterie (modèles à démarreur électrique seulement)
- Section 4 Entretien et dépannage
- Réf. A0000061814
Owner’s Manual for Portable Generator 19
Inspect Spark Arrester Screen
1. Loosen clamp (A) and remove screw. See
Figure 4-7.
2. Inspect screen (B) and replace if torn, per-
forated or otherwise damaged. If screen is
not damaged, clean with commercial sol-
vent.
3. Replace spark arrestor cone (C) and
screen (B). Secure with clamp and screw.
Figure 4-7. Spark Arrestor Screen
Valve Clearance
Important: Please contact an Independent
Authorized Service Dealer for service assis-
tance. Proper valve clearance is essential for
prolonging the life of the engine.
Check valve clearance after the first fifty-hours
of operation. Adjust as necessary.
• Intake — 0.1 ± 0.02mm (cold), (0.004" ±
0.0008" inches)
• Exhaust — 0.15 ± 0.02mm (cold) (0.006" ±
0.0008" inches)
Storage
General
It is recommended to start and run the genera-
tor for 30 minutes, every 30 days. If this is not
possible, refer to the following list to prepare
unit for storage.
• DO NOT place a storage cover on a hot
generator. Allow unit to cool to room tem-
perature before storage.
• DO NOT store fuel from one season to
another unless properly treated.
• Replace fuel container if rust is present.
Rust in fuel will cause fuel system prob-
lems.
• Cover unit with a suitable protective, mois-
ture resistant cover.
• Store unit in a clean and dry area.
• Always store generator and fuel away from
heat and ignition sources.
Prepare Fuel System for Storage
Fuel stored over 30 days can go bad and
damage fuel system components. Keep fuel
fresh, use fuel stabilizer.
If fuel stabilizer is added to fuel system, pre-
pare and run engine for long term storage.
Run engine for 10-15 minutes to circulate sta-
bilizer throughout fuel system. Adequately
prepared fuel can be stored up to 24 months.
NOTE: If fuel has not been treated with fuel
stabilizer, it must be drained into an approved
container. Run engine until it stops from lack
of fuel. Use of fuel stabilizer in fuel storage
container is recommended to keep fuel fresh.
1. Change engine oil.
2. Remove spark plug.
3. Pour tablespoon (5-10cc) of clean engine
oil or spray a suitable fogging agent into
cylinder.
4. Pull starter recoil several times to distrib-
ute oil in cylinder.
5. Install spark plug.
6. Pull recoil slowly until resistance is felt.
This will close valves so moisture cannot
enter engine cylinder. Gently release
recoil.
Change Oil
Change engine oil before storage. See
Change Engine Oil.
(000108)
WARNING
Hot Surfaces. When operating machine, do not
touch hot surfaces. Keep machine away from
combustibles during use. Hot surfaces could
result in severe burns or fire.
000586
A
B
C
(000143)
DANGER
Explosion and Fire. Fuel and vapors are extremely
flammable and explosive. Store fuel in a well
ventilated area. Keep fire and spark away. Failure
to do so will result in death or serious injury.
(000109)
WARNING
Risk of Fire. Verify machine has properly
cooled before installing cover and storing
machine. Hot surfaces could result in fire.
(000181)
WARNING
Vision Loss. Eye protection is required to avoid
spray from spark plug hole when cranking engine.
Failure to do so could result in vision loss.