Use and Care Manual
Table Of Contents
- 18-, 20-, 24-inch Band Saws
- 1.0 Warranty and service
- 2.0 Table of contents
- 3.0 IMPORTANT SAFETY INSTRUCTIONS
- 4.0 About this manual
- 5.0 Features and Terminology
- 6.0 Specifications
- 7.0 Base hole centers
- 8.0 Setup and assembly
- 8.1 Shipping contents
- 8.2 Unpacking
- 8.3 Spotting the band saw
- 8.4 Rear rail
- 8.5 Front rail and guide rail
- 8.6 Fence assembly
- 8.7 Resaw fence
- 8.8 Fence to table clearance
- 8.9 Setting cursor (zero) position
- 8.10 Setting table parallel to blade
- 8.11 Setting fence parallel to blade
- 8.12 Fence locking tightness
- 8.13 Dust collection
- 9.0 Electrical connections
- 10.0 Adjustments
- 11.0 Operating controls
- 12.0 Operation
- 13.0 Maintenance
- 14.0 Blade Selection
- 15.0 Blade Selection Guide
- 16.0 Troubleshooting PM1800B/2013B/2415B Band Saws
- 17.0 Replacement Parts
- 17.1.1 Complete Machine with Accessories – PM 1800B & 2013B Exploded View I
- 17.1.2 Complete Machine with Accessories – PM 1800B & 2013B Exploded View II
- 17.1.3 Complete Machine with Accessories – PM2415B Exploded View I
- 17.1.4 Complete Machine with Accessories – PM2415B Exploded View II
- 17.1.5 Complete Machine with Accessories – PM1800B, PM2013B and PM2415B – Parts List
- 17.2.1 Upper Wheel Assembly – Exploded View
- 17.2.2 Upper Wheel Assembly – Parts List
- 17.3.1 Lower Wheel Assembly – Exploded View
- 17.3.2 Lower Wheel Assembly – Parts List
- 17.4.1 Upper Wheel Sliding Bracket Assembly –Exploded View
- 17.4.2 Upper Wheel Sliding Bracket Assembly –Part List
- 17.5.1 Brake Linkage Assembly – Exploded View
- 17.5.2 Brake Linkage Assembly – Parts List
- 17.6.1 Lower Blade Guide Support Assembly – Exploded View
- 17.6.2 Lower Blade Guide Support Assembly – Parts List
- 17.7.1 Upper Blade Guide Support Assembly – Exploded View
- 17.7.2 Upper Blade Guide Support Assembly – Parts List
- 17.8.1 Trunnion Support Bracket Assembly – Exploded View
- 17.8.2 Trunnion Support Bracket Assembly – Parts List
- 17.9.1 Guide Bar Bracket Assembly – Exploded View
- 17.9.2 Guide Bar Bracket Assembly – Parts List
- 17.10.1 Gear Bracket Assembly – Exploded View
- 17.10.2 Gear Bracket Assembly – Parts List
- 17.11.1 Miter Gauge Assembly – Exploded View
- 17.11.2 Miter Gauge Assembly – Parts List
- 17.12.1 Fence Assembly – Exploded View
- 17.12.2 Fence Assembly – Parts List
- 18.0 Electrical Connections
23
Figure 36: belt detension
Figure 37: belt position
Figure 38: belt deflection
10.14 Drive belt tension and
replacement
The drive belt and pulleys are properly adjusted at
the factory. However, belt tension should be
occasionally checked when the band saw is new, as
a new belt may stretch slightly during the breaking-
in process.
If the belt becomes worn, cracked, frayed or glazed,
it should be replaced as follows:
Refer to Figures 36 and 38.
1. Disconnect machine from power source.
2. Open upper and lower doors and remove blade.
3. Remove screw from lower wheel shaft and
remove lower wheel.
4. Loosen motor lock handle.
5. Raise motor lift handle and retighten motor lock
handle to hold motor in raised position.
6. Remove old belt and install new one, making
sure it seats properly in the pulley grooves.
7. Loosen motor lock handle and allow motor to
lower.
8. The weight of the motor itself should generally
produce the proper tension for the belt. Check
tension by pushing with moderate pressure
against center of belt (Figure 38). An
adequately tensioned belt will deflect about
1/2”. If tension isn’t strong enough, push down
on the motor.
9. Tighten motor lock handle, reinstall lower
wheel, and install hex nut securely on shaft.
10. Re-check blade tension and tracking before
operating saw.