Use and Care Manual
Table Of Contents
- 18-, 20-, 24-inch Band Saws
- 1.0 Warranty and service
- 2.0 Table of contents
- 3.0 IMPORTANT SAFETY INSTRUCTIONS
- 4.0 About this manual
- 5.0 Features and Terminology
- 6.0 Specifications
- 7.0 Base hole centers
- 8.0 Setup and assembly
- 8.1 Shipping contents
- 8.2 Unpacking
- 8.3 Spotting the band saw
- 8.4 Rear rail
- 8.5 Front rail and guide rail
- 8.6 Fence assembly
- 8.7 Resaw fence
- 8.8 Fence to table clearance
- 8.9 Setting cursor (zero) position
- 8.10 Setting table parallel to blade
- 8.11 Setting fence parallel to blade
- 8.12 Fence locking tightness
- 8.13 Dust collection
- 9.0 Electrical connections
- 10.0 Adjustments
- 11.0 Operating controls
- 12.0 Operation
- 13.0 Maintenance
- 14.0 Blade Selection
- 15.0 Blade Selection Guide
- 16.0 Troubleshooting PM1800B/2013B/2415B Band Saws
- 17.0 Replacement Parts
- 17.1.1 Complete Machine with Accessories – PM 1800B & 2013B Exploded View I
- 17.1.2 Complete Machine with Accessories – PM 1800B & 2013B Exploded View II
- 17.1.3 Complete Machine with Accessories – PM2415B Exploded View I
- 17.1.4 Complete Machine with Accessories – PM2415B Exploded View II
- 17.1.5 Complete Machine with Accessories – PM1800B, PM2013B and PM2415B – Parts List
- 17.2.1 Upper Wheel Assembly – Exploded View
- 17.2.2 Upper Wheel Assembly – Parts List
- 17.3.1 Lower Wheel Assembly – Exploded View
- 17.3.2 Lower Wheel Assembly – Parts List
- 17.4.1 Upper Wheel Sliding Bracket Assembly –Exploded View
- 17.4.2 Upper Wheel Sliding Bracket Assembly –Part List
- 17.5.1 Brake Linkage Assembly – Exploded View
- 17.5.2 Brake Linkage Assembly – Parts List
- 17.6.1 Lower Blade Guide Support Assembly – Exploded View
- 17.6.2 Lower Blade Guide Support Assembly – Parts List
- 17.7.1 Upper Blade Guide Support Assembly – Exploded View
- 17.7.2 Upper Blade Guide Support Assembly – Parts List
- 17.8.1 Trunnion Support Bracket Assembly – Exploded View
- 17.8.2 Trunnion Support Bracket Assembly – Parts List
- 17.9.1 Guide Bar Bracket Assembly – Exploded View
- 17.9.2 Guide Bar Bracket Assembly – Parts List
- 17.10.1 Gear Bracket Assembly – Exploded View
- 17.10.2 Gear Bracket Assembly – Parts List
- 17.11.1 Miter Gauge Assembly – Exploded View
- 17.11.2 Miter Gauge Assembly – Parts List
- 17.12.1 Fence Assembly – Exploded View
- 17.12.2 Fence Assembly – Parts List
- 18.0 Electrical Connections
27
13.0 Maintenance
Before doing maintenance on
the machine, disconnect it from the electrical
supply by pulling out the plug or switching off
the main switch! Failure to comply may cause
serious injury.
Clean the band saw regularly to remove any
resinous deposits and sawdust.
Keep the miter slot, and the guide bearings, clean
and free of resin.
Keep the blade clean and sharp. Check it
periodically for cracks or other signs of wear.
The drive belt should be checked periodically. If it
looks worn, frayed, glazed or otherwise damaged,
replace it.
Remove any deposits from the band wheels to avoid
vibration and potential blade breakage.
Vacuum or blow out dust from inside the cabinet.
(Use proper dust mask equipment).
The table surface must be kept clean and free of rust
for best results. If rust appears, you can use a
mixture of household ammonia, good commercial
detergent and #000 steel wool. Alternatively,
commercial rust removers can be found at many
hardware stores.
Apply a light coat of paste wax to the table. There
are also products in aerosol form available in major
hardware stores and supply catalogs. Whatever
method is chosen, the coating should protect the
metal and provide a smooth surface, without
staining workpieces.
If the power cord is worn, cut, or damaged in any
way, have it replaced immediately.
13.1 Lubrication Points
Periodically apply a light, non-hardening grease to
rack and pinion system of guide post (Figure 46).
Grease sliding surfaces of table trunnions (Figure
47). Also grease contact area of trunnion scale and
handwheel gear (Figure 47), and the other gears
connected to the handwheel (Figure 48).
Grease blade tension screw (Figure 49).
Oil any pins, shafts, and joints. Do not get oil on
pulleys or belts.
Note: Bearings on the band saw are sealed for life
and do not require lubrication.
Figure 46
Figure 47
Figure 48
Figure 49