Use and Care Manual
Table Of Contents
- 18-, 20-, 24-inch Band Saws
- 1.0 Warranty and service
- 2.0 Table of contents
- 3.0 IMPORTANT SAFETY INSTRUCTIONS
- 4.0 About this manual
- 5.0 Features and Terminology
- 6.0 Specifications
- 7.0 Base hole centers
- 8.0 Setup and assembly
- 8.1 Shipping contents
- 8.2 Unpacking
- 8.3 Spotting the band saw
- 8.4 Rear rail
- 8.5 Front rail and guide rail
- 8.6 Fence assembly
- 8.7 Resaw fence
- 8.8 Fence to table clearance
- 8.9 Setting cursor (zero) position
- 8.10 Setting table parallel to blade
- 8.11 Setting fence parallel to blade
- 8.12 Fence locking tightness
- 8.13 Dust collection
- 9.0 Electrical connections
- 10.0 Adjustments
- 11.0 Operating controls
- 12.0 Operation
- 13.0 Maintenance
- 14.0 Blade Selection
- 15.0 Blade Selection Guide
- 16.0 Troubleshooting PM1800B/2013B/2415B Band Saws
- 17.0 Replacement Parts
- 17.1.1 Complete Machine with Accessories – PM 1800B & 2013B Exploded View I
- 17.1.2 Complete Machine with Accessories – PM 1800B & 2013B Exploded View II
- 17.1.3 Complete Machine with Accessories – PM2415B Exploded View I
- 17.1.4 Complete Machine with Accessories – PM2415B Exploded View II
- 17.1.5 Complete Machine with Accessories – PM1800B, PM2013B and PM2415B – Parts List
- 17.2.1 Upper Wheel Assembly – Exploded View
- 17.2.2 Upper Wheel Assembly – Parts List
- 17.3.1 Lower Wheel Assembly – Exploded View
- 17.3.2 Lower Wheel Assembly – Parts List
- 17.4.1 Upper Wheel Sliding Bracket Assembly –Exploded View
- 17.4.2 Upper Wheel Sliding Bracket Assembly –Part List
- 17.5.1 Brake Linkage Assembly – Exploded View
- 17.5.2 Brake Linkage Assembly – Parts List
- 17.6.1 Lower Blade Guide Support Assembly – Exploded View
- 17.6.2 Lower Blade Guide Support Assembly – Parts List
- 17.7.1 Upper Blade Guide Support Assembly – Exploded View
- 17.7.2 Upper Blade Guide Support Assembly – Parts List
- 17.8.1 Trunnion Support Bracket Assembly – Exploded View
- 17.8.2 Trunnion Support Bracket Assembly – Parts List
- 17.9.1 Guide Bar Bracket Assembly – Exploded View
- 17.9.2 Guide Bar Bracket Assembly – Parts List
- 17.10.1 Gear Bracket Assembly – Exploded View
- 17.10.2 Gear Bracket Assembly – Parts List
- 17.11.1 Miter Gauge Assembly – Exploded View
- 17.11.2 Miter Gauge Assembly – Parts List
- 17.12.1 Fence Assembly – Exploded View
- 17.12.2 Fence Assembly – Parts List
- 18.0 Electrical Connections
30
15.0 Blade Selection Guide
Identify the material and thickness of your workpiece. The chart will show the recommended PITCH, blade TYPE,
and FEED RATE.
Key: H – Hook L – Low
S – Skip M – Medium
R – Regular H – High
Example: 10/H/M means 10 teeth per inch / Hook Type Blade / Medium Feed
For Radius Cutting
Study the part drawing or prototype, or actually
measure the smallest cutting radius required, and
locate this radius (in inches) on the chart at the right.
Follow the curve to where the approximate blade
width is specified. If a radius falls between two of the
curves, select the widest blade that will saw this
radius.
This procedure should be used for making initial
blade selections. These recommendations can, of
course, be adjusted to meet specific requirements
of a cutting job. Compromises may be necessary if
you cannot find all needed specifications in a single
blade.
Table 2