Use and Care Manual
Table Of Contents
- 18-, 20-, 24-inch Band Saws
- 1.0 Warranty and service
- 2.0 Table of contents
- 3.0 IMPORTANT SAFETY INSTRUCTIONS
- 4.0 About this manual
- 5.0 Features and Terminology
- 6.0 Specifications
- 7.0 Base hole centers
- 8.0 Setup and assembly
- 8.1 Shipping contents
- 8.2 Unpacking
- 8.3 Spotting the band saw
- 8.4 Rear rail
- 8.5 Front rail and guide rail
- 8.6 Fence assembly
- 8.7 Resaw fence
- 8.8 Fence to table clearance
- 8.9 Setting cursor (zero) position
- 8.10 Setting table parallel to blade
- 8.11 Setting fence parallel to blade
- 8.12 Fence locking tightness
- 8.13 Dust collection
- 9.0 Electrical connections
- 10.0 Adjustments
- 11.0 Operating controls
- 12.0 Operation
- 13.0 Maintenance
- 14.0 Blade Selection
- 15.0 Blade Selection Guide
- 16.0 Troubleshooting PM1800B/2013B/2415B Band Saws
- 17.0 Replacement Parts
- 17.1.1 Complete Machine with Accessories – PM 1800B & 2013B Exploded View I
- 17.1.2 Complete Machine with Accessories – PM 1800B & 2013B Exploded View II
- 17.1.3 Complete Machine with Accessories – PM2415B Exploded View I
- 17.1.4 Complete Machine with Accessories – PM2415B Exploded View II
- 17.1.5 Complete Machine with Accessories – PM1800B, PM2013B and PM2415B – Parts List
- 17.2.1 Upper Wheel Assembly – Exploded View
- 17.2.2 Upper Wheel Assembly – Parts List
- 17.3.1 Lower Wheel Assembly – Exploded View
- 17.3.2 Lower Wheel Assembly – Parts List
- 17.4.1 Upper Wheel Sliding Bracket Assembly –Exploded View
- 17.4.2 Upper Wheel Sliding Bracket Assembly –Part List
- 17.5.1 Brake Linkage Assembly – Exploded View
- 17.5.2 Brake Linkage Assembly – Parts List
- 17.6.1 Lower Blade Guide Support Assembly – Exploded View
- 17.6.2 Lower Blade Guide Support Assembly – Parts List
- 17.7.1 Upper Blade Guide Support Assembly – Exploded View
- 17.7.2 Upper Blade Guide Support Assembly – Parts List
- 17.8.1 Trunnion Support Bracket Assembly – Exploded View
- 17.8.2 Trunnion Support Bracket Assembly – Parts List
- 17.9.1 Guide Bar Bracket Assembly – Exploded View
- 17.9.2 Guide Bar Bracket Assembly – Parts List
- 17.10.1 Gear Bracket Assembly – Exploded View
- 17.10.2 Gear Bracket Assembly – Parts List
- 17.11.1 Miter Gauge Assembly – Exploded View
- 17.11.2 Miter Gauge Assembly – Parts List
- 17.12.1 Fence Assembly – Exploded View
- 17.12.2 Fence Assembly – Parts List
- 18.0 Electrical Connections
34
Trouble Probable Cause Remedy
Machine will not
start/restart or
repeatedly trips circuit
breaker or blows
fuses.
(continued)
Switch failure.
If the start/stop switch is suspect, you
have two options: Have a qualified
electrician test the switch for function, or
purchase a new start/stop switch and
establish if that was the problem on
change-out.
Band Saw does not
come up to speed.
Extension cord too light or too long.
Replace with adequate size and length
cord.
Low current. Contact a qualified electrician.
17.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-
274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of
your machine available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from
Powermatic. Some parts are shown for reference only, and may not be available individually.