Use and Care Manual
Table Of Contents
- CNC Routers
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 1.1 Switch lock-out
- 2.0 About this manual
- 3.0 Table of contents
- 4.0 CNC router features
- 5.0 Specifications for Powermatic CNC Router Machines
- 6.0 Glossary
- 7.0 Setup and assembly
- 7.1 Shipping contents for PM-2X2R
- 7.2 Unpacking and cleanup
- 7.3 Tools required for assembly
- 7.4 Shipping contents for PM-2X4SP
- 7.5 Unpacking and cleanup
- 7.6 Tools required for assembly
- 7.7 Assembling stand (all models)
- 7.8 Installing router table on stand
- 7.9 Completing assembly
- 7.10 Installing router (PM-2X2R only)
- 7.11 Installing top guard
- 8.0 Electrical connections
- 9.0 Setup for operation
- 10.0 Operations
- 11.0 Controller functions
- 12.0 User-maintenance
- 13.0 Additional accessories
- 14.0 Troubleshooting PM-2X2R and PM-2X4SP CNC routers
- 15.0 Replacement Parts
- 15.1.1 PM-2X2R Assembly I – Exploded View
- 15.1.2 PM-2X2R Assembly II – Exploded View
- 15.1.3 PM-2X2R Assemblies – Parts List
- 15.2.1 PM-2X2S Stand Assembly – Exploded View
- 15.2.2 PM-2X2S Stand Assembly – Parts List
- 15.3.1 PM-2X4SP Assembly I – Exploded View
- 15.3.2 PM-2X4SP Assembly II – Exploded View
- 15.3.3 PM-2X4SP Assemblies – Parts List
- 15.4.1 PM-2X4S Stand Assembly – Exploded View
- 16.0 Electrical Connections for CNC Router
- 17.0 Warranty and service
14
7.7 Assembling stand (all models)
NOTE: Assembly procedures for stand are identical
for PM-2X2R and PM-2X4SP. The only difference is
side panels and braces are longer on the 2X4
model.
1. Thread a nut (S10) onto each leveling foot (S9,
Figure 7-9).
2. Turn front and rear panels upside down. You
may wish to lay down a rug or cardboard to
prevent scratching top surface of panels.
3. Install four leveling feet and four casters into
bottom of panels, as shown. Tighten caster
screws securely. The leveling feet can be
adjusted later.
Figure 7-9
4. Partially insert eight screws with washers
(Figure 7-10) into threaded holes inside both
panels. Push washers against screw head.
5. Install cross braces over screws, and tighten.
NOTE: The flange on the cross brace must face
toward the outside. (TIP: Use rubber mallet to
tap cross braces even with panel edges.)
Figure 7-10
6. Flip assembly on its side, and install a third
cross brace in similar manner (Figure 7-11).
Tighten screws.
7. Flip assembly again (right side up) and install
fourth cross brace. Tighten screws.
Figure 7-11
8. Install lower supports (S2) to bottom edge of
storage cabinet in the orientation shown in
Figure 7-12.
Figure 7-12
9. Install open side panel (S7, Figure 7-13) and
tighten screws.
10. Place storage cabinet with supports into stand
so it is flush with side panel. See Figure 7-13.
Tighten screws.