Replacement Part List

MODEL 45R PARTS LIST

ITEM PART NO. DESCRIPTION QTY. REQ’D.

1 08-45-00-010 SPRING CLIP 1

2 08-45-00-020 FEEDER CHANNEL 1

5 08-45-00-050 ROLLER PIN ASSEMBLY 1

5R 08-45-00-05R ROLLER 1

13 08-45-00-130 FOOT SCREW 4

13N 08-45-00-13N LOCKNUT 4

14 08-45-00-140 GATE 1

15 08-45-00-150 FOOT 1

16 08-45-00-960 SPRING CONTAINER SCREW 2

17 08-45-00-170 SPRING CONTAINER 1

18 08-45-00-180 FEEDER SPRING 1

19 08-45-00-930 SPRING CONTAINER LOCK WASHER 2

23 08-45-00-230 DOWEL PIN 2

25 08-45-00-250 HANDLE ASSEMBLY 1

29 08-45-00-290 ADAPTER PLATE PIN ASSEMBLY 1

37R 07-45-00-704 RATCHET PLUNGER 1

38 08-45-00-380 DRIVING BLADE 1

39 08-45-00-400 LEFT PLUNGER LINER 1

40R 08-45-00-705 RIGHT PLUNGER LINER 1

41 08-45-00-410 PLUNGER SPRING PIN 1

45 08-45-00-450 PLUNGER SPRING 1

58 08-45-00-580 BLADE RETAINER 1

59R 08-45R-00-59 RATCHET ASSEMBLY 1

60 08-45-00-710 RATCHET ACCESS PLATE 1

61 08-45-00-711 RATCHET ACCESS PLATE SCREW 2

400 06-99-400 TOE STAND 1

#8-25 06-99-010 #825 ADAPTER PLATE ASSEMBLY FOR 3/4"T&G 1

ITEM PART NO. DESCRIPTION QTY. REQ’D.

#8-26 06-99-040 #826 ADAPTER PLATE ASSEMBLY FOR 1/2" T&G 1

#8-26 06-99-04A #826 ADAPTER PLATE ASSEMBLY FOR 5/8" T&G 1

#8-25 06-99-04B #825 ADAPTER PLATE ASSEMBLY FOR 22MM" T&G 1

70 06-99-720 #825 NO-MAR PAD (STICK-ON) .015 Thick 1

71 06-99-721 #825 NO-MAR PAD (STICK-ON) .060 Thick 1

72 08-45-TU-KIT MODEL 45R TUNE-UP KIT 1

73 08-45R-OVH-KIT MODEL 45R OVERHAUL KIT 1

MODEL 45R ACCESSORIES

PAGE 1
2 MODEL 45R PARTS LIST ITEM 1 2 5 5R 13 13N 14 15 16 17 18 19 23 25 29 37R 38 39 40R 41 45 58 59R 60 61 400 #8-25 PART NO.
PAGE 2
3 MODEL 45R PARTS LIST IMPORTANT When ordering repair parts, specify both model and serial number
PAGE 3
POWERCLEAT® NAIL LENGTH CHART This chart will assist you in determining the proper length of Powercleat nails to use for various thicknesses of flooring when sub-flooring member varies as to species and thickness. Vertical penetration of the Powercleat nails under the hardwood floor is shown for each application. This is only a guide. Results should be tested in the field before proceeding.
PAGE 4
5 MODEL 45R & 101R RATCHET REPAIR INSTRUCTIONS • With a 5/32 allen wrench, unscrew the two #10-32 socket head cap screws from the access plate. • Replace access plate. Important: Make sure access plate is replaced as shown, with indent facing in towards ratchet. • Remove access plate by turning nailer over. • • Remove ratchet insert assembly. Fasten access plate back to body using a 5/32 allen wrench and the two socket head cap screws. • Install new ratchet insert assembly as shown below.