Operation Manual

ManualsBrandsPowerplus ManualsSawPOWX07573T

POWX07573T EN

1 APPLICATION .................................................................................. 3

2 DESCRIPTION (FIG A & B) ............................................................. 3

3 PACKAGE CONTENT LIST ............................................................. 3

4 SYMBOLS ........................................................................................ 4

5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4

5.1 Working area ........................................................................................................... 4

5.2 Electrical safety ....................................................................................................... 4

5.3 Personal safety ....................................................................................................... 4

5.4 Power tools use and care ....................................................................................... 5

5.5 Service ..................................................................................................................... 5

6 ADDITIONAL SAFETY INSTRUCTIONS ........................................ 5

7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS ................ 7

8 ASSEMBLY ...................................................................................... 7

8.1 Assembling the extension hoops .......................................................................... 7

8.2 Assembling the lever .............................................................................................. 7

8.3 Assembling the clamp ............................................................................................ 7

9 OPERATING INSTRUCTIONS ........................................................ 8

9.1 Transporting the mitre saw .................................................................................... 8

9.2 Dust and chip extraction ........................................................................................ 8

9.3 Clamping the work piece ........................................................................................ 8

9.4 Horizontal mitre angle............................................................................................. 8

9.5 Adjusting of the cutting angle (Fig 1) .................................................................... 8

9.6 Vertical bevel angle (Fig. 2) .................................................................................... 8

9.7 Slide lock adjustment ............................................................................................. 8

9.8 Depth stop (Fig. 3) ................................................................................................... 9

9.9 Switching ON / OFF ................................................................................................. 9

9.10 Laser (13) ................................................................................................................. 9

9.11 Dust bag .................................................................................................................. 9

9.12 Sawing ..................................................................................................................... 9

9.13 Sawing special work pieces ................................................................................. 10

9.14 Replacing the saw blade (Fig. 4) .......................................................................... 10

Summary of content (13 pages)

PAGE 1
POWX07573T EN 1 APPLICATION .................................................................................. 3 2 DESCRIPTION (FIG A & B) ............................................................. 3 3 PACKAGE CONTENT LIST ............................................................. 3 4 SYMBOLS ........................................................................................ 4 5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4 5.1 Working area .........................
PAGE 2
10 POWX07573T EN CLEANING AND MAINTENANCE................................................. 10 10.1 Cleaning................................................................................................................. 10 10.2 Connecting cable .................................................................................................. 11 11 TECHNICAL DATA ........................................................................ 11 12 CUTTING CAPACITY..........................................
PAGE 3
EN POWX07573T DOUBLE BEVEL SLIDING MITRE SAW 2000W POWX07573T 1 APPLICATION This power tool is intended as a stationary machine for making straight and cross cuts in wood. You can saw hard and soft wood as well as chip and fibre boards. Only adults may use this tool. WARNING! For your own safety, read this manual and the general safety instructions carefully before using the appliance. Your power tool should only be given to other users together with these instructions. 2 DESCRIPTION (FIG A & B) 1. 2. 3.
PAGE 4
EN POWX07573T 4 SYMBOLS The following symbols are used in this manual and/or on the machine: Denotes risk of personal injury or damage to the tool. Wear eye protection . Read manual before use. In accordance with essential requirements of the European directive(s) Wear gloves. Class II - The machine is double insulated; Earthing wire is therefore not necessary. 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions.
PAGE 5
POWX07573T       EN Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury. Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely.
PAGE 6
POWX07573T                       EN Only use correctly sharpened saw blades. Never exceed the maximum speed that is indicated on the saw blade. Before installing the saw blade, clean the axle, the flanges (especially the assembly surfaces) and the hexagonal nut. Incorrect mounting can lead to vibrations/knocking or slipping of the saw blade. Prevent that the saw comes into contact with metals, such as nails and screws.
PAGE 7
POWX07573T      EN Arsenic and chrome from chemically treated wood. The hazard to your health from such exposures is dependent on how frequently you do this kind of work. Measures for reducing your exposure to such chemicals: Always work in well-ventilated surroundings and with certified safety equipment, such as dust masks that have been specially designed for filtering out microscopic particles. For sawing operations, connect the equipment to a dust exhaust system.
PAGE 8
POWX07573T EN 9 OPERATING INSTRUCTIONS 9.1 Transporting the mitre saw To transport the power tool, use the retaining pin (19). Pull the mitre saw downwards and lock it in the lowered position by pull, twist and push in the retaining pin. That way, the saw is secured. 9.2 Dust and chip extraction For integrated dust extraction, place the dust bag (20) on the sawdust outlet. For external dust, you can use a vacuum cleaner hose.
PAGE 9
EN POWX07573T 9.8 Depth stop (Fig. 3) When not a complete cut through the work piece is desired, use the depth stop bolt to control the depth of cut. Only adjust the front bolt. The rear bolt is used to prevent the blade from cutting the table during normal cutting. Do not adjust the rear bolt.       Unlock the retaining pin. Raise the saw head assembly. Push the depth stop to the left to use the depth stop bolt settings. Pull down on the saw head to check the current setting.
PAGE 10
EN POWX07573T       Switch on the power tool. Move the handle (15) slowly downwards. You have to push the safety switch (17) before you can do this. For long workpieces you should use the slide; loosen the locking knob for this purpose. Saw trough the work piece. Switch off the power tool. Wait until the saw blade (2) has come to a complete standstill before removing the work piece. 9.13 Sawing special work pieces Curved or round work pieces need to be secured against slipping.
PAGE 11
EN POWX07573T 10.2 Connecting cable If the connecting cable (or mains plug) is damaged, it must be replaced. Replacement of the connecting cable should only be carried out by a qualified specialist (qualified electrician). 11 TECHNICAL DATA Nominal Voltage Power rating No load speed Protection class Blade size 230V ~ 50 Hz 2000W 4200min-1 II 305mm x 30 mm x 2.
PAGE 12
EN POWX07573T 15 TROUBLE SHOOTING PROBLEM Motor does not run. Vibrations are too strong. POSSIBLE CAUSE No electricity arrives at the machine. SOLUTION Check the power supply and the power line. The motor is overloaded or overheated. Screws or parts are loose. Allow the machine to run idle for about 2 minutes to cool down. Tighten all screws. The mitre saw is not correctly mounted. Mount the mitre saw correctly. Secure the work piece.
PAGE 13
EN POWX07573T  Your appliance must be returned undismantled to your dealer in an acceptably clean state, (in its original blow-moulded case if applicable to the unit), accompanied by proof of purchase. 17 ENVIRONMENT Should your appliance need replacement after extended use, do not discard it with the household rubbish but dispose of it in an environmentally safe way. Waste produced by electrical machine items should not be handled like normal household rubbish.