BASIC OPERATION INSTRUCTIONS Synergy TRU-Balance TM Dynamic G90 Controller ACN# 088 609 661
SAFETY GUIDELINES WARNING! An authorized Pride Provider or a qualified technician must perform the initial setup of this product and must perform all of the instructions in this manual. The symbols below are used throughout this owner's manual and on the controller to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/ situation.
TABLE OF CONTENTS LABEL INFORMATION ................................................................... 4 INTRODUCTION ................................................................................ 5 DYNAMIC G90 CONTROLLER .................................................... 7 PRECAUTIONARY GUIDELINES ............................................... 7 OPERATING THE DYNAMIC G90 CONTROLLER ............ 11 CONTROLLER COMMUNICATIONS CONNECTOR ......... 15 OFF-BOARD CHARGER SOCKET ..............................
LABEL INFORMATION PRODUCT SAFETY SYMBOLS The symbols below are used on the controller to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual. Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and store in a clean and dry condition.
Basic Operation Instructions 5 INTRODUCTION WELCOME to Pride Mobility Products Corporation (Pride). The product you have purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that the design features will provide you with the conveniences you expect during your daily activities. Understanding how to safely operate and care for this product should bring you years of trouble free operations and service.
Basic Operation Instructions NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and we will be glad to send you a new one immediately. My authorized Pride Provider Is: Name: Address: Phone Number: Purchase Date: Dynamic G90 Controller www.pridemobility.
Basic Operation Instructions 7 DYNAMIC G90 CONTROLLER The Dynamic G90 controller is a fully-programmable, modular electronic controller system that allows you to operate your power chair. It is designed to allow the user to have complete control over chair movement and speed. The controller has been pre-programmed to meet a typical user’s needs.
Basic Operation Instructions Electromagnetic and Radio Frequency Interference (EMI/RFI) WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can have an adverse affect on the performance of electrically-powered mobility vehicles.
Basic Operation Instructions 9 Dynamic G90 Controller Features Figure 1 provides information on the Dynamic G90 components and connections. Use this diagram to familiarize yourself with the function and location of each component before using the Dynamic G90 controller. The following functions are available with the Dynamic G90 controller: Joystick Control The joystick is used to control the direction and speed of the power chair.
Basic Operation Instructions 7 Segment Display Display for showing the selected drive profile. Also displays Drive Inhibit, Attendant Mode, & Lighting Mode when applicable. Actuator Indicator Lights Battery Condition Meter A series of six LEDs which indicates charge level. Left Leg Rest Hazard Right Turn ECU Icon Lock/System Status Headlight Elevate Right Leg Rest On/Off Key Toggles system power on and off. Headlights/ Hazard Key Toggles Headlights (short press) on and off.
Basic Operation Instructions 11 OPERATING THE DYNAMIC G90 CONTROLLER The Dynamic G90 controller is used to operate your power chair and all of its components. The Dynamic G90 controller consists of (See figure 2): 1. Joystick 2. Keypad & display 3. Controller communications connector 4. 3-pin off-board charger socket NOTE: This section describes standard Dynamic G90 control functions.
Basic Operation Instructions Figure 2. Dynamic G90 Controller DRIVE MODE & ACTUATOR DISPLAY BATTERY CONDITION METER RIGHT TURN INDICATOR LEFT TURN INDICATOR HEADLIGHT INDICATOR HAZARD LIGHT INDICATOR LOCK/SYSTEM STATUS LED ECU MODE INDICATOR ON/OFF KEY HEADLIGHTS/ HAZARD KEY MODE KEY HORN KEY RIGHT TURN INDICATOR KEY LEFT TURN INDICATOR KEY Figure 3. Dynamic G90 Keypad and Display Dynamic G90 Controller www.pridemobility.
Basic Operation Instructions 13 Lock/System Status LED The lock/system status LED is normally on when the system is powered up, and off when the system is powered down. See figure 3. This light will flash green if there is an internal fault, or if an OONAPU fault has occurred. See “Out Of Neutral At Power Up.” The lock/system status LED also serves as the magnetic locking area, a feature that enables you to “lockout” unauthorized users.
Basic Operation Instructions Mode Key The mode key enables you to select a drive profile and a power accessory mode. Your Dynamic G90 controller was preprogrammed for five drive profiles— 1 (slowest) to 5 (fastest). The drive profile is indicated by a number in the center of the keypad (7 segment display). NOTE: The drive mode settings are preset at the factory. If your authorized Pride Provider changes these settings, please make note of these changes. To change the drive profile: 1.
Basic Operation Instructions 15 CONTROLLER COMMUNICATIONS CONNECTOR This connects the Dynamic G90 to the power chair’s batteries, motors, and motor brakes. OFF-BOARD CHARGER SOCKET You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front of the Dynamic G90 (see figure 1). If you use an off-board charger, the charger current should not exceed 8 amps. Contact your authorized Pride Provider for more information.
Basic Operation Instructions SLEEP MODE The power chair controller features a sleep mode that must be enabled through programming. Sleep mode is a built-in circuit that will automatically shut off the main power if the joystick is not moved in any direction for a period of time. This time factor is programmed into the controller. To restore power and continue, turn your power chair on. OUT OF NEUTRAL AT POWER UP (OONAPU) Your power chair joystick is equipped with Out Of Neutral At Power Up (OONAPU).
Basic Operation Instructions Error Fault Code 1 2 3 4 5 6 7 8 9 10 11 12 Diagnosis DX Module Fault An auto download has occurred. The controller is not correctly programmed. The connection between the power module and the joystick module may be faulty. DX Accessory The accessory module (CLAM) has Fault a fault. Left Motor The connection between the power (or connection) module and the left motor is either Fault open or is shorted or the motor itself is shorted.
Basic Operation Instructions CARE AND MAINTENANCE Refer to your power chair owner’s manual for proper cleaning and disposal instructions. WARRANTY For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of charge, the controller or any of its components found upon examination by an authorized representative of Pride to be defective in material and/or workmanship. Dynamic G90 Controller www.pridemobility.
NOTES www.pridemobility.
Pride Mobility Products Corporation 182 Susquehanna Avenue Exeter, PA 18643-2694 USA Pride Mobility Products Company 380 Vansickle Road Unit 350 St. Catharines, Ontario L2R 6P7 Canada Pride Mobility Products Ltd. 32 Wedgwood Road Bicester, Oxon OX26 4UL UK Pride Mobility Products Australia Pty. Ltd. 21 Healey Road Dandenong, 3175 Victoria, Australia Pride Mobility Products Italia S.r.l. Via del Progresso - ang. Via del Lavoro Loc.
