I 3 5 i n t e g r at e d A m p l i f i e r User Guide
CAUTION TO REDUCE THE RISK OF FIRE, REPLACE WITH THE SAME TYPE AND RATING OF FUSE. ATTENTION UTILISER UN FUSIBLE DE RECHANGE MÊME TYPE. Safety compliance This product has been designed to meet the IEC 60065 international electrical safety standard.
2.4G and 5G FCC Statements This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. This device complies with Part 15 of the FCC Rules.
I35 Integrated Amplifier User Guide
C ontents Welcome! 6 Technical specification 13 Getting Started 7 Speaker outputs 13 1 Unpack the I35 7 Analogue inputs 13 2 Connect speakers 7 Analogue outputs 13 3 Connect inputs 7 Performance 13 4 Connect power 7 General 13 Back-panel connections 8 Additional information 14 Phase 14 Using the remote control 9 Burn-in 14 Selecting I35 mode 9 RS232 and trigger 14 Fitting the batteries 9 Using the I35 with a CD35 14 Using the I35 10 Error messages 14 Front panel
W elcome ! Congratulations on selecting your new I35 Integrated Amplifier This user guide describes the features and explains how to set up the amplifier for the best sound quality and ease of operation in order to allow for the most enjoyable reproduction of sound from all your sources. For additional support and assistance please contact your local authorized Primare dealer, or visit our website at www.primare.net.
Getting S tarted 1 Unpack the I35 2 Connect speakers 4 Connect power Your I35 is supplied with: The I35 is designed to be connected directly to a pair of loudspeakers. l Plug one end of the mains cable supplied with the I35 into the power connector on the back panel, and connect the other end to a wall socket. l l l l l l This User Guide Mains cable IR cable Trigger cable C25 remote control with batteries AC Polarity Pen If any of these items are missing please contact your supplier.
Back-panel connections The following diagram explains the function of each of the connectors on the back panel: Slot for network module RS232 Trigger IR in/out Slot for DAC module Balanced analogue inputs Unbalanced analogue inputs On/off Analogue outputs Right speaker Left speaker Power and fuse I35 Integrated Amplifier User Guide
U sing the remote control Selecting I35 mode The remote control can operate any associated Primare products you have in your system. To make the remote control operate the I35 l Press the AMP AV button once. To make the remote control operate another product Press briefly to mute the sound Indicators light when pressing a button Top: AMP, PRE, or CD mode Bottom: AV, SC, or AUX mode l Press the AMP AV, CD SC, or PRE AUX button as appropriate.
U sing the I 3 5 Front panel controls Selecting a source Changing the display brightness Selector The I35 provides a choice of 5 inputs. Initially these are labelled as shown in the following table, but you can give them your own aliases to suit the sources in your system; see ALIAS, page 11. To change the front panel display brightness Selects an input. In the settings menus navigates between settings. Standby O Switches the I35 to standby, or switches it on from standby.
C onfiguring the settings Using the settings menus INPUT SETTINGS You can view and change the I35 settings from the front panel or remote control. The INPUT SETTINGS menu allows you to customise the inputs to suit the sources in your system: To display the settings menu A1 SETTINGS 20 l Press the @ button on the front panel, or the MENU button on the remote control.
AUDIO SETTINGS GENERAL SETTINGS The AUDIO SETTINGS menu allows you to customise the balance and start-up volume, and the maximum and mute volume. The GENERAL SETTINGS menu allows you to configure the general operation of the I35: AUDIO SETTINGS 20 BALANCE STARTUP VOLUME MAXIMUM VOLUME 00LR00 30 99 BALANCE Allows you to adjust the balance between 00LR-9 (far left), 00LR00 (centred, default) and -9LR00 (far right). STARTUP VOLUME Sets the general startup volume to between 0 and 60. The default is 20.
T echnical specification Speaker outputs Performance General Power Gain Control 2 x 150W into 8Ω, 2 x 300W into 4Ω Analogue inputs Balanced inputs 2 x XLR, 30kΩ impedance Unbalanced inputs 3 x RCA, 15kΩ impedance Analogue outputs Preamplifier output: 16.5dB Speaker output: 42.5dB C25 system remote control RS232 IR in/out Trigger out Analogue frequency response Power Consumption Distortion Operating: <37W Line output: 0dB 20Hz – 20kHz: -0.2dB THD + N: < 0.
A dditional information These instructions help you get the best possible sound from your I35. Phase The phase of the AC supply can make a significant difference to the sound. Use the Polarity Pen supplied with the I35 to verify which pin is live on your AC power cable.
Index A Alias (settings menus) 11 Analogue inputs and outputs 8 Audio settings menu 12 Auto-dim (settings menus) 12 Auto sense (settings menus) 11 B Back panel 8 Balance (settings menus) 12 Balanced inputs 8 C Clipping 11 D G General settings menu 12 Input (settings menus) 11 Input gain (settings menus) 11 Inputs, connecting 7 Factory reset (settings menus) 12 Firmware (settings menus) 12 Front panel (settings menus) 12 Settings menus 11 IR input 8 Sources Connecting 7 L LED brightness (setti
T H E S O U N D A N D V I S I O N O F S C A N D I N AV I A S I N C E 1 9 8 6 L imstensgatan 7 , 2 1 6 1 6 L imhamn , S weden More information at primare.