Product Manual

ManualsBrandsPro Series ManualsElectricC8100-NS - 1 HP Chemical Resistant Submersible Pump

PHCC Pro Series Chemical

Resistant Pumps

Operating Instructions C8050 & C8100

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

roperty damage! Retain instructions for future reference.

Description

PHCC Pro Series submersible chemical resistant pumps are rated for continuous

duty. Pumps are strong and dependable, and when used intermittently in a sump

application, extends the life of the pump. PSC motor design saves energy, reduces

operation costs and provides better service. Intended for pumping non-flammable

fluids compatible with pump component materials.

General Safety Instructions

SAVE THESE INSTRUCTIONS.

This manual contains important

SAFETY WARNINGS and OPERATING

INSTRUCTIONS for the C8050 & C8100

pumps. You will need to refer to it

before attempting any installation or

maintenance.

ALWAYS keep these instructions with

the unit so that they will be easily

accessible.

Failure to read and follow these

warnings and instructions could result

in property damage, serious injury, or

death.

Risk of electric

shock. To reduce

this risk, observe the following

precautions.

• ALWAYS disconnect the pump from

the power source before servicing or

making adjustments.

• NEVER handle the pump or motor

with wet hands or when standing on

a wet or damp surface while the

pump is plugged into the power

source.

• MAKE SURE THERE IS A PROPERLY

GROUNDED RECEPTACLE

AVAILABLE. This pump is wired

with a 3-prong grounded plug. To

reduce the risk of electric shock, be

certain that it is only connected to a

properly grounded, 3-prong

receptacle (preferably with ground

fault circuit interrupt). If you have a

2-prong receptacle, have a licensed

electrician replace it with a 3-prong

receptacle according to local codes

and ordinances.

• NEVER bypass grounding wires or

remove the ground prong from the

plug.

• DO NOT use an extension cord. The

electrical outlet should be within the

length of the pump’s power cord,

and at least 4 feet above the floor

Specifications

C8050 C8100

HP 1/2 1

Motor Type PSC PSC

Voltage 60 Hz 115 VAC 115 VAC

Amps 4.7 11.3

Water Flow (GPM) at Total Feet of Head

5 Ft. 74 90

10 Ft. 64 82

15 Ft. 51 69

20 Ft. 40 61

25 Ft. 27 53

30 Ft. 13 45

35 Ft. -- 37

40 Ft. -- 24

Max Head 36 Ft. 49 Ft.

Max Dia Solids 1/4” 3/8”

Dimensions

C8050 C8100

HP 1/2 1

Pump Discharge 2” 2”

Materials of Construction

Pump Housing 304 SS 304 SS

Impeller 304 SS 304 SS

Motor Casing

304 SS 304 SS

Inlet Screen 304 SS 304 SS

Motor Shaft 304 SS 304 SS

Mech. Seals (2) Carbon/Ceramic/Viton

Fasteners 304 SS 304 SS

Overall Dimensions

Length 9.1” 10.4”

Width 6.3” 7.5”

Height 16.3” 18.1”

Weight (lbs.) 23.0 46.0

Summary of content (7 pages)

PAGE 1
C8050 & C8100 Operating Instructions Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
PAGE 2
PHCC Pro Series Operating Instructions C8050 and C8100 PHCC Pro Series Chemical Resistant Pumps General Safety Instructions (Continued) level to minimize potential hazards from flood conditions. • DO protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. • MAKE SURE the supply circuit has a fuse or circuit breaker rated to handle the power requirements noted on the nameplate of the pump.
PAGE 3
PHCC Pro Series Operating Instructions Models C8050 and C8100 Installation (Continued) NOTE: When using a check valve, an air bleed hole of 1⁄8” (3.2mm) needs to be drilled in the discharge pipe. The hole should be below the check valve, but above the water line. A small stream of water will escape through this air bleed hole when the pump is running, so the hole should be drilled at an angle toward the bottom of the sump pit. 8. Install a gate valve or ball valve as required by any codes. 9.
PAGE 4
PHCC Pro Series Operating Instructions C8050 and C8100 PHCC Pro Series Chemical Resistant Pumps Chemical Compatibility Chart Beer Milk Sodium Sulfate Beet Sugar Liquids Cotton Seed Oil Sodium Sulfide Calgon Linseed Oil Sodium Thiosulphate ("Hypo") Carbonic Acid Soybean Oil Soy Sauce Cider Potassium Bromide Stearic Acid Coffee Potassium Carbonate Stoddard Solvent Cream Potassium Chloride Tanning Liquors Detergents Sea Water Tomato Juice Epsom Salts (Magesium Sulfate) Sodium Bicarb
PAGE 5
PHCC Pro Series Operating Instructions Models C8050 and C8100 Troubleshooting Chart Symptom The pump will not start or run Thermal protector tripping or not functioning Pump starts and stops too frequently Pump will not shut off Possible Cause(s) Corrective Action 1. Pump is not plugged in 1. Plug pump in properly (see instructions) 2. Water is not high enough to activate the pump 2. Make sure float switch is positioned properly 3. Open circuit 3.
PAGE 6
C8050 and C8100 PHCC Pro Series Operating Instructions PHCC Pro Series Chemical Resistant Pumps Troubleshooting Chart (Continued) Symptom Insufficient or no water volume Abnormal sound or vibration Possible Cause(s) Corrective Action 1. Check valve on secondary pump will not close and water re-circulates within the system 1. Replace the check valve on the secondary pump 2. Worn impeller 2. Replace impeller & adjust spacing between impeller and cover 3. Partially blocked impeller 3.
PAGE 7
PHCC Pro Series Operating Instructions Models C8050 and C8100 LIMITED WARRANTY GLENTRONICS ONE-YEAR LIMITED WARRANTY. PHCC PRO SERIES CHEMICAL RESISTANT PUMPS, MODELS COVERED IN THIS MANUAL, ARE WARRANTED BY GLENTRONICS, INC. TO THE ORIGINAL USER AGAINST DEFECTS IN WORKMANSHIP OR MATERIALS UNDER NORMAL USE FOR ONE YEAR AFTER DATE OF PURCHASE.