www.proform.com Model No. PFTL20511.3 Serial No. Write the serial number in the space above for reference. Serial Number Decal ACTIVATE YOUR WARRANTY To register your product and activate your warranty today, go to www.proformservice.com/ registration. CUSTOMER CARE For service at any time, go to www.proformservice.com. Or call 1-888-533-1333 Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT Please do not contact the store.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. 12.
20. The heart rate monitor is not a medical device. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general. 28. Over exercising may result in serious injury or death. If you feel faint or if you experience pain while exercising, stop immediately and cool down. 29. Do not store the television in temperatures below -40° F (-40° C) or above 140° F (60° C).
34. Upon completion of any service or repairs to the treadmill or the television, ask the service technician to perform safety checks to confirm that the unit is in proper operating condition. 38. Use a jumper wire not smaller than No. 6 AWG (13.3 mm2) copper, or the equivalent, when a separate antenna-grounding electrode is used. See NEC Section 810-21 (j) or your local codes and ordinances. 35. Use No. 10 AWG (5.3 mm2) copper, No. 8 AWG (8.4 mm2) aluminum, No. 17 AWG (1.
STANDARD SERVICE PLANS all 7
BEFORE YOU BEGIN Thank you for selecting the revolutionary PROFORM® PERFORMANCE 1850 treadmill. The PERFORMANCE 1850 treadmill offers an impressive selection of features designed to make your workouts at home more enjoyable and effective. And when you’re not exercising, the unique treadmill can be folded up, requiring less than half the oor space of other treadmills. reading this manual, please see the front cover of this manual.
PART IDENTIFICATION CHART Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached. Extra hardware may be included.
ASSEMBLY • To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. • Left parts are marked “L” or “Left” and right parts are marked “R” or “Right.” • Assembly requires two persons. • To identify small parts, see page 9. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you nish all assembly steps.
3. Pull the Upright Wire (81) and the base ground wire (A) through the indicated hole in the Base (94). 3 Attach the base ground wire (A) to the Base (94) with a #8 x 1/2" Ground Screw (10). Hole 81 A 94 10 4. Identify the Left Upright (89). Have a second person hold the Left Upright near the Base (94). 4 81 89 See the inset drawing. Tie the wire tie in the Left Upright (89) securely around the end of the Upright Wire (81).
5. Hold the Left Upright (89) against the Base (94). Be careful not to pinch the Upright Wire (81). Insert two 3/8" x 1 1/4" Screws (8) with two 3/8" Star Washers (13) and two 3/8" x 2 3/4" Screws (7) into the Left Upright. 5 81 89 Partially tighten the 3/8" x 2 3/4" Screws (7) and the 3/8" x 1 1/4" Screws (8) until the heads of the Screws touch the Left Upright (89); do not fully tighten the Screws yet. Note: It may be helpful to use the Short Hex Key (64) on the Screw shown.
7. Cut the plastic ties in the Left Handrail (88) and the Right Handrail (87). If necessary, press the 5/16" Cage Nuts (31) back into place. 7 87 122 Identify the Left Handrail (88) and hold it near the Left Upright (89). Insert the Upright Wire (81) through the bracket on the bottom of the Left Handrail. Pull the Upright Wire out of the end of the Left Handrail. 31 81 90 Hold the Right Handrail (87) near the Right Upright (90).
9. Set the console assembly face down on a soft surface to avoid scratching the console assembly. 9 Console Assembly Remove and discard all of the screws (B) attaching the Crossbar (93). Next, lift off the Crossbar. B 93 10. IMPORTANT: To avoid damaging the Crossbar (93), do not use power tools and do not overtighten the #10 x 3/4" Screws (9) or the #10 x 3/4" Flat Head Screws (112). 10 9 112 35 93 9 Orient the Crossbar (93) as shown.
11. With the help of a second person, hold the console assembly near the Left Handrail (88). 11 Connect the Upright Wire (81) to the console wire. See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Remove the wire tie from the Upright Wire.
14. Slide the Left Handrail Cover (85) onto the Left Handrail (88). Slide the Right Handrail Cover (86) onto the Right Handrail (87). Attach each Handrail Cover with a #8 x 1/2" Screw (1). 14 86 87 1 85 88 1 15. Hold the Left Upright Cover (79) against the console assembly. Align the holes in the Left Upright Cover with the holes in the Left Upright (89). Attach the Left Upright Cover with three #8 x 1/2" Screws (1). 15 Attach the Right Upright Cover (80) to the Right Upright (90) in the same way.
. IMPORTANT: See page 21 and plug in the power cord. Next, see page 25 and turn on the power. 17 IMPORTANT: Make sure to follow all instructions in this step. See page 33; follow steps 1, 2, and 4. When the frame stops moving, remove the key from the console and unplug the power cord. 18. IMPORTANT: Before you begin this step, make sure that you have read and followed all of the instructions in step 17. 18 56 Raise the Frame (56) to the position shown.
19. Attach the Rear Feet (57) to the Frame (56) as shown with four #8 x 3/4" Screws (2). 19 Lower the Frame (56) (see HOW TO LOWER THE TREADMILL FOR USE on page 40). 57 57 2 2 56 20. Press the Grommet (77) into the square hole in the Base (94). 20 94 77 21. Remove the #8 x 1/2" Machine Screw (114) and the Wire Cover (117) from the TV Bracket (118).
22. With the help of a second person, hold the TV assembly near the console assembly, and connect the wires. 22 TV Assembly Attach the TV assembly to the back of the console assembly with four 1/4" x 3/4" Screws (116). Be careful not to pinch any wires. Start all four Screws, and then tighten them. Console Assembly Wires 116 23. Place the treadmill near the coaxial cable from your wall (or device). Connect the coaxial cable to the Upright Coaxial Cable (122).
THE CHEST HEART RATE MONITOR HOW TO PUT ON THE HEART RATE MONITOR The heart rate monitor consists of a chest strap and a sensor. Insert the tab on one end of the chest strap into the hole in one end of the sensor as shown. Then, press the end of the sensor under the buckle on the chest strap. The tab should be flush with the front of the sensor.
HOW TO CONNECT THE TREADMILL HOW TO CONNECT THE POWER CORD nominal 120-volt circuit capable of carrying 15 or more amps. To avoid overloading the circuit, do not plug other electrical devices, except for lowpower devices such as cell phone chargers, into the surge suppressor or into an outlet on the same circuit. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.
Before operating the 15" digital TV, you must connect an antenna or a 75 ohm CATV cable to the 75 ohm terminal, an AV cable to the audio/video input jack, or an HDMI cable to the HDMI input jack. Note: Use a CATV cable to connect to an external source such as a cable box, satellite TV box, VCR, or analog cable. No CATV cable, antenna, or adapter; AV cable; or HDMI cable is included. HOW TO CONNECT AN ANTENNA Place an indoor VHF antenna or an outdoor combination VHF/UHF antenna in the desired location.
HOW TO CONNECT A VCR, DVD PLAYER, OR OTHER DEVICE USING AN AV CABLE HOW TO CONNECT A DVD OR BLU-RAY PLAYER OR OTHER DEVICE USING AN HDMI CABLE 1. Connect the three-pronged end of an RCA AV Cable to your VCR, DVD player, or other device. 1. Connect one end of an HDMI Cable to your DVD or Blu-ray player or other device. 2. Plug in the power cord of your device. See your VCR, DVD player, or other device’s user’s manual for proper grounding instructions. 2. Plug in the power cord of your device.
OPERATION AND ADJUSTMENT CONSOLE DIAGRAM FEATURES OF THE CONSOLE As you exercise, the console will display instant exercise feedback. You can also measure your heart rate using the handgrip heart rate monitor or the chest heart rate monitor. The treadmill console offers an impressive array of features designed to make your workouts more effective and enjoyable. The console features revolutionary iFit technology that enables the treadmill to communicate with your wireless network.
HOW TO TURN ON THE POWER HOW TO USE THE TOUCH SCREEN IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before you turn on the power. If you do not do this, you may damage the console display or other electrical components. The console features a tablet with a full-color touch screen. The following information will help you become familiar with the tablet’s advanced technology: Plug in the power cord (see page 21).
HOW TO SET UP THE CONSOLE The console is now ready for you to begin working out. The following pages explain the various workouts and other features that the console offers. Before using the treadmill for the rst time, set up the console. To use the manual mode, see page 27. To use an onboard workout, see page 29. To use a set-a-goal workout, see page 30. To use an iFit workout, see page 31. 1. Connect to your wireless network.
HOW TO USE THE MANUAL MODE of the numbered 1 Step Incline/Decline buttons. Each time you press one of the buttons, the incline will gradually change until it reaches the selected incline setting. 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 25. Note: It may take a minute for the console to be ready for use. Note: The rst time you adjust the incline, you must rst calibrate the incline system (see step 4 on page 33). 2. Select the main menu. 5. Monitor your progress.
If desired, adjust the volume by pressing the Vol increase and decrease buttons on the console. 7. Turn on the fan if desired. The fan features multiple speed settings and an auto mode. When the auto mode is selected, the speed of the fan will automatically increase and decrease as the speed of the walking belt increases and decreases. To pause the workout, touch one of the menu buttons or press the Stop button on the console. To continue the workout, touch the Resume button or the Start button.
HOW TO USE AN ONBOARD WORKOUT If the speed and/or incline settings are too high or too low at any time during the workout, you can override the settings by pressing the Speed or Incline buttons. If you press a Speed button, you can then manually control the speed (see step 3 on page 27). If you press an Incline button, you can then manually control the incline (see step 4 on page 27). To return to the programmed speed and/or incline settings of the workout, first, view the profile.
HOW TO USE A SET-A-GOAL WORKOUT The workout will function in the same way as the manual mode (see page 27). 1. Insert the key into the console. The workout will continue until you reach the goal that you set. The walking belt will then slow to a stop, and a workout summary will appear on the screen. After you view the workout summary, touch the Finish button to return to the main menu. You may also be able to either save or publish your results using one of the options on the screen.
HOW TO USE AN IFIT WORKOUT Before some workouts will download, you must add them to your schedule on iFit.com. Note: To use an iFit workout, you must have access to a wireless network (see HOW TO USE THE WIRELESS NETWORK MODE on page 34). An iFit account is also required. For more information about the iFit workouts, please see www.iFit.com. When you select an iFit workout, the screen will show the name, duration, and distance of the workout.
HOW TO USE THE EQUIPMENT SETTINGS MODE console will function normally when you plug in the power cord, press the power switch into the reset position, and insert the key into the console. However, when you remove the key, the screen will show a demo presentation. The console features an equipment settings mode that allows you to select a language, the unit of measurement, and a timezone; to turn on and turn off the display demo mode; and to enable or disable the key and/or a passcode.
HOW TO USE THE MAINTENANCE MODE Note: Occasionally, a firmware update may cause your console to function slightly differently. These updates are always designed to improve your exercise experience. The console features a maintenance mode that allows you to update the console firmware, calibrate the incline of the treadmill, view machine information, and view a button’s keycode. 4. Calibrate the incline system of the treadmill. 1. Select the settings main menu. Touch the Calibrate Incline button.
HOW TO USE THE WIRELESS NETWORK MODE An information box will ask if you want to connect to the wireless network. Touch the Connect button to connect to the network or touch the Cancel button to return to the list of networks. If the network has a password, touch the password entry box. A keyboard will appear on the screen. To view the password as you type it, touch the Show Password checkbox. The console features a wireless network mode that allows you to set up a wireless network connection. 1.
HOW TO USE THE SOUND SYSTEM HOW TO USE THE INTERNET BROWSER To play music or audio books through the console’s speakers, you must connect your MP3 player, CD player, or other personal audio player to the console. Note: To use the browser, you must have access to a wireless network including an 802.11b/g/n router with SSID broadcast enabled (hidden networks are not supported). Plug one end of your audio wire into the audio jack on the side of the console.
HOW TO OPERATE THE 15" DIGITAL TV remote control (see HOW TO USE THE REMOTE CONTROL on page 37). When the volume is adjusted, a graphic will appear on-screen to show which volume setting is selected. The 15" digital TV can be controlled with the control buttons found on your exercise equipment’s console or with the remote control (see page 37). 5. Mute the TV if desired. 1. Turn on the 15" digital TV. Press the Mute button to turn off the TV’s audio output.
HOW TO USE THE REMOTE CONTROL Press the Display button to view information about the current program and the broadcast or cable signal. The first time you use the remote control, insert batteries (see HOW TO REPLACE THE BATTERIES IN THE REMOTE CONTROL at the right). Press the CC button repeatedly to turn on or turn off closed captioning. See step 6 on page 36 to adjust closed captioning settings. Press the Source button repeatedly to select the input source.
HOW TO ADJUST THE TELEVISION SETTINGS 4. Adjust the channel settings. The 15" digital TV has a menu that allows you to adjust and personalize television settings. The Channel menu allows you to save channels in the TV memory and select settings for channels. Note: You can only access this menu if TV is selected as the input source.
5. Adjust the parental control settings. Select Menu Language to change the language used in the menus. The Parental menu allows you to block or allow various settings on the 15" digital TV. Select Clock to adjust the TV clock’s time zone, auto setting, time setting, day of the week setting, and daylight saving time setting. First, enter the Lock Parental Code password, which is a 4-digit PIN. Note: The default password is 0000. Once the password has been entered, the Parental menu will be unlocked.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL HOW TO MOVE THE TREADMILL To avoid damaging the treadmill, adjust the incline to zero percent before you fold the treadmill. Then, remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. Before moving the treadmill, fold it as described at the left. CAUTION: Make sure that the latch knob is locked in the storage position.
TROUBLESHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. c. Remove the key from the console, and then reinsert it. d. If the treadmill still will not run, please see the front cover of this manual. SYMPTOM: The power does not turn on SYMPTOM: The console displays remain lit when you remove the key from the console a.
Locate the Reed Switch (52) and the Magnet (50) on the left side of the Pulley (49). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (14), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) and run the treadmill for a few minutes to check for a correct speed reading.
SYMPTOM: The walking belt is off-center or slips when walked on SYMPTOM: The treadmill will not connect to the wireless network a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt.
SYMPTOM: The volume cannot be turned up • Ignition (black spots or horizontal streaks that appear or a picture that flutters or drifts)—Usually this is caused by interference from automobile ignition systems, neon lamps, electric drifts, or other electric appliances. Try changing the position of the treadmill or other electric appliances to correct the problem.
EXERCISE GUIDELINES Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone.
PART LIST Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 21 57 1 2 4 1 4 4 2 7 4 2 4 17 2 1 2 2 9 2 2 2 4 1 4 2 2 4 1 4 2 2 6 4 7 4 1 2 4 4 1 1 1 1 1 2 2 4 1 1 Model No. PFTL20511.3 R0813A Description Key No. Qty.
Key No. Qty. 101 102 103 104 105 106 107 108 109 110 111 112 113 1 1 1 1 1 2 1 1 1 1 3 2 4 Description Key No. Qty.
15 48 27 26 39 40 14 2 38 37 59 30 34 23 14 39 102 61 40 2 64 63 2 44 57 15 60 45 43 27 26 47 2 42 23 19 46 2 2 2 2 57 30 34 59 30 34 12 56 2 59 21 2 23 47 40 39 2 38 51 14 6 2 2 14 50 49 52 18 55 40 39 41 19 14 2 2 10 53 23 20 12 24 35 59 30 34 46 2 21 10 48 54 3 18 EXPLODED DRAWING A Model No. PFTL20511.
EXPLODED DRAWING B Model No. PFTL20511.
EXPLODED DRAWING C Model No. PFTL20511.
EXPLODED DRAWING D Model No. PFTL20511.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.