Owner's Manual

11
USING THE RESTORATION 600
The RESTORATION 600 is designed for up to four
adults. The four water jets can be regulated to provide
a relaxing massage to sooth away stress, and the
strength of the water massage can be adjusted by the
air control. The RESTORATION 600 holds 300 gal-
lons of water and offers an automatic, programmable
heating (70°F to 104°F) and filtration system.
The guidelines below explain how to properly use the
RESTORATION 600. Follow these guidelines to main-
tain the spa for your long-term enjoyment.
PRIMING THE SPA JET UNIT
The water pump in the spa jet unit must be primed
before you use the RESTORATION 600 the first time.
You must also prime the pump before using the unit
each time you re-fill the RESTORATION 600.
To prime the spa jet
unit, remove the
primer cap from the
console. Fill the spa
jet unit with at least 64
oz. of water. Replace
and tighten the
primer cap. IMPOR-
TANT: The spa jet
unit may be seriously damaged if the pump is not
properly primed, or if the primer cap is not
replaced and fully tightened.
PLUGGING IN THE RESTORATION 600
Once the RESTORATION 600 is filled with enough
water to cover the water jets and the pump has been
primed, the power cord can be plugged in and the spa
jet unit can be turned on. Note: The first time the
power cord is plugged in, the spa jet unit will turn on
automatically.
When connecting the power cord, plug the power cord
directly into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on the
same circuit. Replace the power cord immediately if it
becomes damaged.
The power cord is equipped with a Ground Fault
Circuit Interrupter (GFCI), located at the end of the
power cord. You should always test the GFCI before
using the RESTORATION 600.
First, turn on the RESTORATION 600 by pressing the
power button on the console. Once the unit is run-
ning, press the GFCI “test” button. The RESTORA-
TION 600 should shut off. Press the “reset” button.
The RESTORATION 600 should resume normal oper-
ation. If the RESTORATION 600 continues to run after
the “test” button is pressed, then the GFCI is dam-
aged. Do not use the RESTORATION 600 until the
GFCI has been repaired or replaced by a qualified
electrician.
STARTING THE RESTORATION 600
Once you have tested the GFCI, you should verify the
water flow from the pumping unit. Set the air control
on the console to the lowest setting (see USING THE
CONSOLE on the next page). The pumping unit will
heat the water as it pumps. Cover the RESTORA-
TION 600 with the spa cover. The spa cover must
be tight. The water will heat at about 1.7°F an hour
with the cover on. If you are using the RESTORA-
TION 600 indoors, and the room temperature is main-
tained at 70°F, it will take approximately 20 to 28
hours for the water to reach the set temperature.
The temperature and water flow can be set or
changed by the controls on the console (see USING
THE CONSOLE on the next page).
TESTING AND TREATING THE WATER
The RESTORATION 600 comes with a starter chemi-
cal pack for maintaining the water in the spa.
Disregard the directions on the individual packages of
“QUICK pHix It DOWN” and “QUICK pHix It UP.”
However, the directions on the bottle of “Non-chlorine
Shox” and “Bromine Base” are correct. Always keep
the chemicals away from children and pets.
The first time you use the spa, you should test and
treat the water. Once you have verified that the spa
jet unit is functioning properly, and have allowed the
water to circulate for a while, you should remove the
spa cover and add 1/3 of the “Bromine Base” bottle,
Test and Reset
Buttons
Grounded circuit capable of
carrying 15 or more amps
GFCI
Primer
Cap