® 93157639_A P250084
30-Year Limited Warranty Progress Lighting fan motors are warranted to the END USER to be free of electrical and/or mechanical defects for a period of 30 (thirty) years from date of sale. Pull chain switches, reverse switches, capacitors and metal finishes are warranted for a period of 1 year. Warping of wooden or plastic blades is not covered by this warranty. The END USER has the option of returning the defective fan to the place of purchase during the first 30 days for a replacement.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Operating Your Fan 8 Care of Your Fan 9 Troubleshooting 9 Specifications 10 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, ensure electricity 2. 3. 4. 5. 6. has been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 4 a b c d 5 2 3 6 Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 4.25” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy 4. Blade Arms (5) 5. Fan Motor Assembly 6. Blades (5) a. Mounting hardware (16 blade attachment screws) b. Electrical hardware & Balancing kit (3 plastic wire connectors, blade balancing kit) c. Pull chain d. Extra blade bracket screw 2.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 4.25 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 10.4 inches. Standard Ceiling Mounting 1. Remove the mounting bracket from the canopy by loosening the four screws on the top of the canopy.
Installing Fan to the Electrical Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. THE MOUNTING BRACKET MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING BRACKET FROM THE TOP DOWN. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 7. 2. Install the ceiling mounting bracket on the electrical box by using the mounting screws provided with the electrical box.
Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. (Figure 9) 1. Connect the two green fan ground wires, located on the downrod and mounting bracket, to the household ground wire. 2. Connect the neutral fan (white) wire to the white neutral household wire. 3.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting bracket. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Install Pull Chain Install the pull chain extension chain and fob (Figure 13). Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. The fan shipped from the factory with the reverse switch positioned to circulate air downward.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start 1. 2. Check main and branch circuit fuses or breakers Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy 1. 2.
FAN SIZE SPEED VOLTS 52” Low High 120 120 ©2016 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 All Rights Reserved FAN POWER CONSUMPTION AIRFLOW (WITHOUT LIGHTS) CFM WATTS 11.86 44.81 2121 4337 AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 178.8 96.79 NET WEIGHT GROSS WEIGHT CUBE FEET 16.76 Lbs 18.41 Lbs 1.33 10.
® Manual de instalación de ventilador de techo 93157639_A P250084
30 años de garantía limitada Los motores de ventilador Progress Lighting están garantizados al USUARIO FINAL por treinta (30) años, a partir de la fecha de compra, de que estarán libres de defectos eléctricos o mecánicos. Los interruptores activados por cadena, interruptores de reversa, capacitores y acabados de metal tienen 1 año de garantía. No están cubiertas por esta garantía las deformaciones de las aspas de madera o plástico.
Normas de seguridad 1 Cómo desempacar el ventilador 2 Cómo instalar el ventilador 3 Cómo usar el ventilador 8 Cuidado del ventilador 9 Solución de problemas 9 Especificaciones 10 Tabla de contenido
LEE Y GUARDA ESTAS INSTRUCCIONES 1. Para disminuir el riesgo de descarga eléctrica, antes de comenzar la instalación asegúrate de que la electricidad ha sido cortada en el cortacircuitos o en la caja de fusibles. 2. Todo el cableado tiene que cumplir con el Código Nacional de Electricidad ANSI/NFPA 70-1999 y los códigos eléctricos locales. La instalación eléctrica debe hacerse por un electricista calificado con licencia. 3.
1 4 a b c d 5 2 3 6 Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: 1. Soporte de montaje (dentro de la cubierta) 2. Conjunto de tubo bajante/bola de 4.25” (15.2 cm) (con pasadores de soporte y de cierre prefijados) 3. 4. 5. 6. Cubierta Brazos de aspas (5) Conjunto del motor del ventilador Aspas (5) a. Herrajes para montaje (16 tornillos para el montaje de aspas) b.
Herramientas necesarias Las figuras 1, 2 y 3 ejemplifican diferentes maneras de montar la caja eléctrica. Destornillador Phillips o de punta plana, llave ajustable, escalera de tijera y cortacables. Provee un soporte fuerte Caja eléctrica empotrada Opciones de montaje Placa de montaje en techo Figura 3 Si no hay una caja eléctrica presente, lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA cortar el suministro de electricidad. Sigue los pasos más abajo para colgar correctamente tu ventilador. NOTA: Se recomienda instalar este ventilador en techo interior estándar usando el tubo bajante incluido. Cuando uses una instalación de techo estándar con el tubo bajante de 4.25 plg (10.8 cm) suministrado, la distancia desde el techo a la parte inferior de las aspas será de unas 10.4 plg (26.4 cm). Montaje estándar en techo 1.
Cómo instalar el ventilador en la caja eléctrica PRECAUCIÓN CUANDO MONTES EL VENTILADOR EN UN TECHO INCLINADO, DEBES USAR EL MÉTODO DE MONTAJE CON TUBO BAJANTE-ESFERA ESTÁNDAR. EL SOPORTE DE MONTAJE TIENE QUE INSTALARSE DE MANERA TAL QUE LAS ABERTURAS DE RANURA QUEDEN EN EL LADO INFERIOR, DESLIZANDO EL SOPORTE DE MONTAJE DE ARRIBA ABAJO.
Sigue estos pasos para conectar tu ventilador al circuito de tu hogar. Usa las tuercas de conexión de cables que vienen con tu ventilador. Asegura los conectores con cinta aislante. Asegúrate de que no existan conexiones o cables sueltos. (Figura 9) 1. Conecta los dos cables verdes de conexión a tierra del ventilador, ubicados en el tubo bajante y el soporte de montaje, al cable de conexión a tierra del hogar. 2.
Cómo finalizar la instalación del ventilador MONTAJE ESTÁNDAR EN CIELO RASO ADVERTENCIA 3. Fija el conjunto de las aspas al motor alineando los orificios de los tornillos en la parte inferior del motor del ventilador con los orificios del brazo de las aspas y apretando los tornillos del motor. Por favor, ten en cuenta que los tornillos del motor están prefijados en los soportes de aspa. (Figura 11) 4. Repite los pasos 1, 2 y 3 para las aspas restantes.
Instala la cadena para interruptor Instala las cadenas de extensión y pendientes decorativos del interruptor de cadena (Figura 13). Interruptor de reversa Llave Figura 13 Las configuraciones de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores y otras. El ventilador se envía desde la fábrica con el interruptor de reversa en posición de hacer circular el aire hacia abajo.
Cuidado del ventilador Solución de problemas Aquí tienes algunas sugerencias para el mantenimiento de tu ventilador. 1. Debido al movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, los soportes y los accesorios de aspas dos veces al año. Comprueba que estén seguros. (No es necesario desmontar el ventilador del cielo raso). 2. Hay que limpiar el ventilador con frecuencia para que luzca como nuevo al paso de los años.
TAMAÑO DEL VENTILADOR VELOCIDAD VOLTIOS (V) 52” (1.32 m) Baja Alta 120 120 ©2016 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 Todos los derechos reservados CONSUMO DE ELECTRICIDAD DEL VENTILADOR (SIN LUCES) VATIOS 11.86 44.81 FLUJO DE AIRE EN PIES CÚBICOS POR MINUTO (CFM). 2121 4337 EFICIENCIA DE FLUJO DE AIRE (MÁS ALTO ES MEJOR) CFM/W 178.8 96.79 PESO NETO 16.76 Lbs PESO BRUTO 18.41 Lbs PIES CÚBICOS 1.33 10.