® 93089913_A P2576
Limited Lifetime Warranty Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Making the Electrical Connections 6 Operating Your Fan 9 Care of Your Fan 10 Troubleshooting 10 Specifications 11 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 8. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 3. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box. 10.
1 5 2 3 7 8 a 9 b 6 10 4 Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 6” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy with Canopy Ring (attached) 4. Decorative Motor Collar Cover 5. Fan Motor Assembly 6. Blades (5) 7. Light Kit Pan 8. Light Kit Fitter Assembly 9. Glass Shade (with frame) 10. Wall Control a. Blade attachment hardware (16 Screws) b.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 6 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 11 inches. Standard Ceiling Mounting Turn Canopy Ring to Remove 8.
Installing Fan to the Electrical Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. THE MOUNTING BRACKET MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING BRACKET FROM THE TOP DOWN. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 8.
Making the Electrical Connections REMEMBER to disconnect the power. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan and supplied with remote control. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. (Figure 10) 1.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING BRACKET MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting bracket. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Installing the Light Kit Pan/Light Kit Fitter Assembly/Glass Shade CAUTION - To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit. THE GLASS IS FRAGILE, USE CARE WHEN INSTALLING THE LIGHT KIT AND THE GLASS SHADE. 1. Loosen but do not remove two of three mounting screws from the fan motor assembly; Remove one mounting screw. (Figure 13) 2.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. The fan shipped from the factory with the reversing switch positioned to circulate air downward. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning, then slide the reversing switch (located at the top of the motor housing, refer to figure 7 on page 4) to opposite position, and turn fan on again.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start Here are some suggestions to help you maintain your fan. 2. Clean your fan periodically to help maintain its new appearance over the years.
FAN SIZE 52” SPEED Low Med High VOLTS 120 FAN POWER CONSUMPTION AIRFLOW CFM (WITHOUT LIGHTS) WATTS 11 36 58 11. Specifications 1773 3591 4586 AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 161 100 79 NET WEIGHT 22.05 Lbs GROSS CUBE WEIGHT FEET 24.47 Lbs 2.1 ©2017 Progress Lighting, Inc. 701 Millennium Blvd.
® Manual de instalación del ventilador de techo 93089913_A P2576
Garantía limitada de por vida Los motores de ventilador Progress Lighting se garantizan al comprador original como libres de defectos eléctricos y/o mecánicos por el tiempo en que estén en posesión de dicho comprador. Los interruptores activados por cadena, los interruptores de reversa, los capacitores y los acabados de metal se garantizan como libres de defectos materiales o de fabricación por un periodo de 1 año desde la fecha de compra.
Normas de seguridad 1 Cómo desempacar el ventilador 2 Cómo instalar el ventilador 3 Cómo hacer las conexiones eléctricas 6 Cómo usar el ventilador 9 Cuidado del ventilador 10 Solución de problemas 10 Especificaciones 11 Tabla de contenido
LEE Y GUARDA ESTAS INSTRUCCIONES 1. Para disminuir el riesgo de descarga eléctrica, antes de comenzar la instalación asegúrate de que la electricidad ha sido cortada en el cortacircuitos o en la caja de fusibles. 2. Todo el cableado tiene que cumplir con el Código Nacional de Electricidad ANSI/NFPA 70-1999 y con los códigos locales de electricidad. La instalación eléctrica debe hacerse por un electricista calificado con licencia. 3.
1 5 2 3 7 8 a 9 b 6 10 4 Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: 1. Soporte de montaje (dentro de la cubierta) 2. Conjunto de tubo bajante/bola de 6" (15.24 cm) con pasadores de soporte y de cierre prefijados. 3. Cubierta con aro de cubierta (acoplado) 4. Cubierta decorativa del collarín del motor 5. Conjunto motor-ventilador 6. Aspas (5) 7. Carcasa del kit de luces 8. Conjunto del soporte del kit de luces 9. Pantalla de vidrio (con armazón) 10.
Herramientas necesarias Destornillador Phillips o de punta plana, llave ajustable, escalera de tijera y cortacables. Las figuras 1, 2 y 3 ejemplifican diferentes maneras de montar la caja eléctrica. Provee un soporte fuerte Placa de montaje en techo Caja eléctrica empotrada Opciones de montaje Figura 3 Si no hay una caja eléctrica presente, lee las siguientes instrucciones. Desconecta la energía retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA cortar la corriente. Sigue los pasos Gira el aro de la cubierta quitarlo Turn Canopy Ring topara Remove más abajo para colgar correctamente tu ventilador. NOTA: Se recomienda instalar este ventilador en techo interior estándar usando el tubo bajante incluido. Cuando uses una instalación de techo estándar con el tubo bajante de 6 pulgadas (15.2 cm) suministrado, la distancia desde el techo a la parte inferior de las aspas será de unas 11 pulgadas (28 cm).
Cómo instalar el ventilador en la caja eléctrica PRECAUCIÓN AL INSTALAR EL VENTILADOR EN UN TECHO INCLINADO, TIENES QUE HACERLO POR EL MÉTODO DE MONTAJE CON TUBO BAJANTE Y BOLA ESTÁNDAR. EL SOPORTE DE MONTAJE TIENE QUE INSTALARSE DE MANERA TAL QUE LAS ABERTURAS DE RANURA QUEDEN SOBRE EL LADO INFERIOR, DESLIZANDO EL SOPORTE DE MONTAJE DESDE LA PARTE SUPERIOR HACIA ABAJO. 1. Pasa los cables de alimentación de 120 V a través del orificio central en el soporte de montaje de techo como muestra la Figura 8. 2.
Cómo hacer las conexiones eléctricas RECUERDA cortar la electricidad. Si crees que no tienes suficiente experiencia o conocimientos en cableado eléctrico, contrata a un electricista con licencia para que instale el ventilador. Sigue estos pasos para conectar tu ventilador al circuito de tu hogar. Usa las tuercas de conexión de cable incluidas con el ventilador y el control remoto. Asegura los conectores con cinta aislante. Asegúrate de que no haya conexiones ni cables sueltos. (Figura 10) 1.
Cómo finalizar la instalación del ventilador MONTAJE ESTÁNDAR EN TECHO ADVERTENCIA CUANDO USES EL MONTAJE DE TUBO BAJANTE Y BOLA ESTÁNDAR, LA PESTAÑA EN EL ARO EN LA PARTE INFERIOR DEL SOPORTE DE MONTAJE DEBE ENCAJAR EN LA RANURA DE LA BOLA DE SOPORTE. SI NO ENCAJA BIEN LA LENGÜETA EN LA RANURA, PUEDE DAÑARSE EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos del soporte de montaje.
Cómo instalar la carcasa del kit de luces/conjunto del soporte del kit de luces/pantalla de vidrio PRECAUCIÓN - Para reducir el riesgo de descarga eléctrica, desconecta el circuito eléctrico de alimentación al ventilador antes de instalar el kit de luces. EL VIDRIO ES FRÁGIL; TEN CUIDADO AL INSTALAR EL KIT DE LUCES Y LA PANTALLA DE VIDRIO. 1. Afloja, pero no quites, dos de los tres tornillos de montaje del conjunto motor-ventilador; retira un tornillo de montaje. (Figura 13) 2.
Las configuraciones de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores y otras. Este ventilador se envía desde la fábrica con el interruptor de reversa en posición de hacer circular el aire hacia abajo.
Cuidado del ventilador Aquí tienes algunas sugerencias para dar mantenimiento a tu ventilador. 1. Por causa del movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, los soportes y los accesorios de aspas dos veces al año. Comprueba que estén seguros. (No es necesario desmontar el ventilador del techo). 2. Limpia el ventilador con frecuencia para que luzca como nuevo al paso de los años.
TAMAÑO DEL VENTILADOR 52" (1.32 m) VELOCIDAD Baja Media Alta VOLTIOS 120 POTENCIA DEL VENTILADOR CONSUMO (SIN LUCES) EN VATIOS (W) FLUJO DE AIRE EN CFM EFICIENCIA DE FLUJO DE AIRE (MÁS ALTO ES MEJOR) CFM/W 36 58 1773 3591 4586 161 11 11. Especificaciones 100 79 PESO NETO PESO PESO BRUTO PESO PIES CÚBICOS 22.05 Lbs 24.47 Lbs 2.1 ©2017 Progress Lighting, Inc. 701 Millennium Blvd.