ITEM #0760192 0760193 LED FLUSHMOUNT CEILING FIXTURES (SET OF 6) Project Source® is a registered trademark of LF, LLC. All Rights Reserved. MODEL #CLL9-6BZ CLL9-6BNK Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Serial Number E479007 Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-389-8827, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. 5 p.m., EST, Friday. AB15942 Lowes.
PACKAGE CONTENTS PART DESCRIPTION QUANTITY A Fixture 6 B Glass Shade 6 (preassembled to fixture (A)) C Mounting Strap 6 D Fixture Screw 12 (preassembled to mounting strap (C)) E Threaded Rod 6 (preassembled to fixture (A)) F Rubber Washer 6 (preassembled to threaded rod (E)) G Nut 6 (preassembled to threaded rod (E) H Finial Plate 6 (preassembled to threaded rod (E)) I Finial 6 (preassembled to threaded rod (E)) A B C D E F H G I HARDWARE CONTENTS (shown actual size) AA Wire Connector Qty.
SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded.
SAFETY INFORMATION CAUTION • All fixtures must be mounted to an outlet box that is supported by the building structure. • If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required. • Do NOT tamper with or attempt to repair LED component of fixture. The light source is designed for this specific application and should not be serviced by untrained personnel.
ASSEMBLY INSTRUCTIONS 2. Remove existing fixtures and disconnect all electrical wiring. 2 Outlet Box 3. Attach mounting strap (C) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding. 3 Outlet Box Tighten machine screws (BB) to secure mounting strap (C) to outlet box.
ASSEMBLY INSTRUCTIONS 4. Remove finial (I), finial plate (H), nut (G) and rubber washer (F) from threaded rod (E). Save all for later use. 4 Remove glass shade (B) from fixture (A). A B E F G I 5. Prepare wire by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 6. Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire. 6 WARNING: Make sure no bare wire or wire strands are visible after making connections. AA Carefully arrange excess wiring and wire connectors (AA) within outlet box. Outlet Box AA 7. Align keyslot holes on fixture (A) with fixture screws (D) on mounting strap (C) and push up. Turn fixture (A) clockwise until it no longer turns.
ASSEMBLY INSTRUCTIONS 9. Restore power and test fixtures (A). 9 If fixtures (A) do not function, please refer to the TROUBLESHOOTING guide on the next page. A A CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture. • Total wattage for each fixture is 14 - 14.5 watts; do not attempt to replace the LEDs.
WARRANTY The distributor warrants all of its lighting fixtures against defects in materials and workmanship for five (5) years from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The distributor will, at its option, repair, replace or refund the purchase price to the consumer.