Installation Guide User guide
Installation Instructions - Upward Extension Display
1Install the Video and USB-Powered cable
If you wish to use the HDMI port on the laptop, please use Digital Video and
USB-Powered Cable. If you wish to use the D-sub (VGA) or mini-Display Port on the
laptop, please purchase the Analog Video and USB-Powered Cable or mini Display Port
and USB-Powered Cable. Connect the Image and Power connector to PRO1301WE Video
port, (1) Insert the latch into the groove of the Video power connector. (2) Slide the Video
power connector toward the left for a proper connection. [Warning: Not inserting the
latch into the groove may result in damage to connector. Please check the Video power
connector is properly connected and not protruding out. If protrusion occurs, the
connection might not be properly connected and monitor will not be able to
operate.]Refer to Fig. 1-1 "Horizontal Display"
2 Connect the PRO1301WE to the laptop
Place the laptop in front of the Mobile Monitor and align the
upper side of the laptop to the lower display edge of the Mobile
Monitor. Connect the USB power connector to the laptop’s USB
port, and then connect the Digital Video connector to the
laptop’s HDMI Video output port.
If Analog Video and USB-Powered cable is used, connect
the Analog Video connector to the laptop’s D-sub port
If miniDP and USB-Powered cable is used, connect the
miniDP connector to the laptop’s D-sub port
3 Adjust the laptop and monitor extension setting
After switching on the laptop, go to Windows’ “Control Panel” to
adjust the monitor extension setting.
If you are using Windows 7:
Select “2.DVI LCD” (Digital Video) or
“2. Display device: VGA” (Analog Video) for Display.
Select “1366x768” for Resolution
Select "Landscape" for Orientation
Select "Extend these displays" for Multiple display, and drag
Display 2 to the top side of Display 1.
4 Switch on the laptop
Switch on the laptop’s monitor and press the power button of
the PRO1301WE; Adjust the brightness: press to adjust the
monitor brighter and press to adjust the monitor dimmer
Installation Instructions- Dual Monitor Display
1 Install the Holder Plate to the front cover of the
laptop’s monitor
[Note: This mode may not be suitable for laptop size smaller than
12" and ultra-thin laptop.]
Open the shaft’s Hinge Plate of the Mobile Monitor to 180° and
place the Mobile Monitor on the laptop's front cover. Tear off the
double-sided adhesive tape on the Holder Plate and attach the
Holder Plate to the laptop, as illustrated. Note:
1) Keep the Holder Plate 2mm from the edge of the laptop
2) Align the Mobile Monitor to the front edge of the laptop's front cover.
3) Keep the direction of the Holder Plate the same as that of the shaft’s
Hinge Plate
4) If the laptop’s front cover is not smooth, use more double-sided
adhesive tape on the Holder Plate as required, before installation.
1-1 Mounting the Holder Plate
[Note: Do not reverse the direction of the Holder Plate
as this will reverse the direction of the Mobile Monitor
after installation.]
2 Install the Video and USB-Powered cable
If you wish to use the HDMI port on the laptop, please use
Digital Video and USB-Powered Cable. If you wish to use the
D-sub (VGA) or mini-Display Port on the laptop, please purchase
the Analog Video and USB-Powered Cable or mini Display Port
and USB-Powered Cable. Connect the Video and Power
connector to PRO1301WE Video port, (1) Insert the latch into
the groove of the Video power connector. (2) Slide the Video
power connector toward the left for a proper connection.
[Warning: Not inserting the latch into the groove may result in
damage to connector. Please check the Video power connector
is properly connected and not protruding out. If protrusion
occurs, the connection might not be properly connected and
monitor will not be able to operate.]Refer to Fig. 1-1 "Horizontal
Display"
3 Install the PRO1301WE to the laptop’s
monitor
As illustrated, align the shaft’s Hinge plate of the
PRO1301WE to the Holder Plate, to slide the shaft’s
Hinge plate into the Holder Plate.
3-1
3-2
Rotate the Mobile Monitor clockwise so that it is parallel to the
laptop; open the laptop monitor and the Mobile Monitor at the
same time, as illustrated. Adjust the angle of the Mobile
Monitor. A recommended angle is between 180° and 225°
3-3 Connect the PRO1301WE to the
laptop
As illustrated, connect the USB power connector to
the laptop's USB port, and then connect the Digital
Video connector to the laptop's HDMI Video output
port
If Analog Video and USB-Powered cable is
used, connect the Analog Video connector
to the laptop’s D-sub port
If miniDP and USB-Powered cable is used,
connect the miniDP connector to the
laptop’s D-sub port
4 Adjust the height of the PRO1301WE on laptop’s front cover ( laptop is smaller than the monitor)
As illustrated, move the Mobile Monitor upward from the laptop’s front cover, press on the positioning clip at the first positioning
hole, and move the Mobile Monitor until the positioning clip pops up from the second positioning hole.
Fig.: Moving the positioning clip from the first positioning hole to the second positioning hole. After Mobile Monitor moves up, it is
no longer fixed to the bottom of the laptop, and the laptop’s monitor can be tilted backward.
[Note: If your laptop is smaller than Mobile Monitor, the cable may get stuck when flipping the Monitor (see lower right figure). ]
5 Adjust the laptop and monitor extension setting
After switching on the laptop, go to “Control Panel” of Windows operating system to
proceed with monitor extension setting.
If you use Windows 7,
Select “2.DVI LCD” (Digital Video) or “2.
display device: VGA” (Analog Video) for
Display
Select “1366x768” for Resolution
Select "Landscape" for Orientation
Select "Extend these displays" for Multiple
displays, and drag Display 2 to the right side
of Display 1.
6 Remove the PRO1301WE from the laptop
As illustrated, align the shaft’s Hinge Plate of the Mobile Monitor with the Holder Plate, and
slide the shaft’s Hinge Plate out from the Holder Plate.
If the laptop smaller than the PRO1301WE
If the laptop smaller than the PRO1301WE
Fig.: Adjust the positioning clip wedge
to the first positioning hole