www.prolink2u.com ® PROLiNK WNR1008 3.75G Wireless-N 4-Port Gigabit Router User’s Manual Version 1.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
TABLE OF CONTENT CHAPTER 1: INTRODUCTION .......................................................................................................................... 1 1.1. Features ..................................................................................................................................................................................................................... 1 1.2. Physical Details ..........................................................................................
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 1: INTRODUCTION The PROLiNK® WNR1008 3.75G Wireless-N 4-Port Gigabit Router supports 4 ports 10/100/1000M Ethernet for LAN and 1 port 10/100/1000M Ethernet interface for WAN. With the advanced MIMO technology, it can support the data transmission rate 6 times more (up to 300 Mbps) and the coverage 3 times more than IEEE 802.11b/g devices. The Wireless Router enables your whole network sharing a high-speed cable or DSL Internet connection.
PROLiNK® WNR1008 www.prolink2u.com WPS WPS Green ON WPS setup successfully OFF WPS is disabled Blinking Wireless LAN WLAN Green OFF WLAN off ON WLAN link / active Blinking LAN Green WPS Green WLAN traffic transmitting OFF LAN function off ON LAN link / active Blinking USB WPS is enabled to make a connection LAN traffic transmitting ON USB is connected OFF USB is disconnected Ports and Buttons (Rear view) Ports and buttons Ant. 1 Ant.
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 2: ABOUT OPERATION MODES This device provides operational applications with Router, AP and Converter modes, which are mutually exclusive. This device is shipped with configuration that is functional right out of the box. If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can MANUALLY switch to the mode you desired by the manufacturer as described in the following sections. 2.1.
PROLiNK® WNR1008 www.prolink2u.com 2.3. When acting as an Access Point (AP), this device connects all the stations (PC/notebook with wireless network adapter) to a wireless network. All stations can have the Internet access if only the Access Point has the Internet connection. 2.4. If set to Converter mode, a device connects to each other through an access point or a base station (gateway or router.
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 3: CONFIGURATION 3.1. Step 1. Connect one end of the Ethernet cable to the LAN port (1~4) of the Wireless Router, another end to your PC or notebook. Step 2. There are two connection methods to connect to Internet (Only one can be used): 2-1. Connect Ethernet cable one end to the WAN (Internet) port of the Wireless Router, the other end to the ADSL or cable modem. 2-2. Or you can insert 3.5G USB card (that provide by your ISP) into USB port. Step 3.
PROLiNK® WNR1008 www.prolink2u.com Refer to below troubleshooting, If you encounter difficulty for connecting the WNR1008 If the WNR1008 does not respond The Wireless Router is properly installed, LAN connection is OK, and it is powered ON. You can test the connection by using the "Ping" command: Please go to Start>Run…> Enter “cmd” command in the column to open the MS-DOS window. Enter the command: ping 192.168.123.
PROLiNK® WNR1008 www.prolink2u.com Common Connection Types The Internet connection type is according to the ISP (Internet Service Provider) that you selected or subscribed. Modem Type IP Type Details ISP Data required Usually, none. Dynamic IP address Your IP address is allocated automatically, when you connect to you ISP. However, some ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address. Cable Modem IP address allocated to you.
PROLiNK® WNR1008 www.prolink2u.com 3.4. LAN Interface Setup 192.168.123.100 255.255.255.0 192.168.123.254 192.168.123.100 192.168.123.200 Item / Function Descriptions / Instructions IP Address Shows the IP address of the Wireless Router (Default IP address is 192.168.123.254) Subnet Mask The subnet mask of the Wireless Router (Default subnet mask is 255.255.255.0.) Default Gateway Shows the default gateway of this Wireless Router.
PROLiNK® WNR1008 www.prolink2u.com Static DHCP button to set the Static DHCP function. IP Address: Enter the fixed IP address that DHCP Server assigned to a certain connected station. MAC Address: Enter the MAC address of a certain station, and then the DHCP Server will to distribute a fixed IP address to the station automatically once they connected. Comment: You can enter a comment to description above IP address or MAC address.
PROLiNK® WNR1008 Item / Function WAN Access Type www.prolink2u.com Descriptions / Instructions Select the WAN Access Type Static IP, DHCP Client, PPPoE, or Mobile Networks from the pull-down list. Default setting is DHCP (Auto Config) enabled. DHCP Client If the DHCP Client be selected, the computer will obtain the IP address automatically. Hostname: Enter the hostname that assigned IP address to your computer in this field. Maximum input is 32 alphanumeric characters (case sensitive).
PROLiNK® WNR1008 www.prolink2u.com will be used when the DNS 1 server fails. PPPoE If the PPPoE be selected, user have to set up the user name and password according to the ISP (Internet Service Provider) that provided the related information. PPPoE Type: Select the PPPoE types, Normal PPPoE, Multiple PPPoE and Unnumbered PPPoE form the pull-down menu. Multi-PPPoE provider: If user select Multiple PPPoE type, user have to setup the PPPoE provider here.
PROLiNK® WNR1008 www.prolink2u.com User have to insert USB card that provide by Internet service provider into the USB port of the wireless router first, therefore, the Mobile networks function can be used. Auto APN: APN (Access Point Name.) If this function be selected, the system will auto detect the mobile network setting via the USB that provide by the Internet service provider (ISP). To use the default settings is recommend.
PROLiNK® WNR1008 www.prolink2u.com Advanced Routing If you connect several routers with this Wireless Router, you may need to set up a predefined routing rule to have more effective network topology/traffic, this is called static route between those routers and the Wireless Router. Item / Function Descriptions / Instructions Enable Dynamic Check to enable the dynamic route function. Route NAT: Select to enable the network address translation function.
PROLiNK® WNR1008 www.prolink2u.com PPTP Server Item / Function Descriptions / Instructions Enable PPTP Server Check to enable the PPTP server function, this function allows you to connect securely from a remote location (such as your home) to an LAN (Local Area Network) located in another location, such as your workplace, business office and so on. User Name Enter username in the column, when the PPTP client try to connect to the PPTP sever should login with the username.
PROLiNK® WNR1008 www.prolink2u.com 3.5. Basic PROLiNK_WNR1008 Item / Function Descriptions / Instructions Disable Wireless Check to disable the wireless function. If the wireless LAN interface be disabled, the WLAN LED on the front LED will LAN Interface be off. Band You can choose one mode of the following you need. 2.4GHz (B): 802.11b supported rate only. 2.4GHz (G): 802.11g supported rate only. 2.4GHz (N): 802.11n supported rate only. 2.4GHz (B+G): 802.11b supported rate and 802.
PROLiNK® WNR1008 www.prolink2u.com User can set up the multiple AP here. Network Type SSID Channel Width If the mode be set to AP or Client mode that the network type can be set to Infrastructure or Ad hoc. A SSID (Service Set Identifier) is referred to a network name because essentially it is a name that identifies a wireless network (case-sensitive). Select 20MHz/40MHz channel width, the channel number will be form 5~11 and auto; Select 20MHz channel width the channel number will be form 1~11 and auto.
PROLiNK® WNR1008 www.prolink2u.com Advanced Item / Function Descriptions / Instructions Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If the 802.11g MIMO Wireless Router often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346.
PROLiNK® WNR1008 www.prolink2u.com Security PROLiNK_WNR1008 Item / Function Descriptions / Instructions Select SSID Select SSID (Service Set Identifier) to set up the security form the pull-down list. Encryption There are several type of encryption modes including Disabled, WEP (Open System), WEP (Shared Key), WEP ( AUTO), WPA (Personal), WPA2 (Personal), and WPA-Mixed. The security default setting is Disabled.
PROLiNK® WNR1008 www.prolink2u.com Authentication Mode: Select Enterprise (RADIUS) or Personal (Pre-Shared Key) mode. WPA Cipher Suite: here supported AES only. WPA2 Cipher Suite: here supported AES only. Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended.
PROLiNK® WNR1008 www.prolink2u.com WDS Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS. To use WDS function: 1. The APs must support WDS function. 2. To set the same SSID (Network name). 3. The channel must be set to the same on the APs. 4.
PROLiNK® WNR1008 www.prolink2u.com 1 2 PROLiNK_WNR1008 3 Step 2. Then go to Wireless > WDS page to (1) enable the WDS function and (2) enter APs Wireless MAC address (please go to Status> Wireless Configuration to make sure the BSSID) to each other to make the WDS connection. Please click Apply button to execute. 1 2 Item / Function Descriptions / Instructions Enable WDS Check the box to enable the WDS function.
PROLiNK® WNR1008 www.prolink2u.com PROLiNK_WNR1008 Data Rate Select the data rate form the pull-down list. Comment Enter a description for the device. Apply Changes After completing the settings on this page, click Apply changes button to save the settings. Reset Click Reset to restore to default values. Enable the WDS function and then click Set Security button to set up the WDS security.
PROLiNK® WNR1008 www.prolink2u.com Refresh: Click to renew the counters information. Close: Click to leave the screen. Current WDS AP List Here shows the current WDS AP information. Delete Selected Click Delete Selected to delete the selected AP information. Delete All Click Delete All to delete all the items. Reset Click Reset to restore the settings. WPS Item / Function Descriptions / Instructions Disable WPS Check the box to disable the WPS function, default setting is enabled.
PROLiNK® WNR1008 www.prolink2u.com Schedule Item / Function Descriptions / Instructions Enable Wireless Check the box to enable the schedule function. Set up the time to schedule the wireless access rule. Select the day Schedule and time you want to enable the wireless function. 3.6. DMZ Settings Item / Function Descriptions / Instructions Enable DMZ Check the box to enable DMZ function.
PROLiNK® WNR1008 www.prolink2u.com URL Filter Settings Item / Function Descriptions / Instructions Enable URL Filtering Check to enable URL filtering function. URL Address Enter the URL address in the field. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current URL address filter information.
PROLiNK® WNR1008 www.prolink2u.com Item / Function Descriptions / Instructions Enable MAC Filtering Check to enable MAC filtering function. MAC Address Enter the client MAC address in the field. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current MAC filter information.
PROLiNK® WNR1008 www.prolink2u.com IP Filtering Item / Function Descriptions / Instructions Enable IP Filtering Check to enable IP filtering function. Local IP Address Enter the local server’s IP address. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Comment You may key in a description for the port range. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings.
PROLiNK® WNR1008 www.prolink2u.com Virtual Server Item / Function Descriptions / Instructions Enable Port Check to enable Port Forwarding function. Forwarding IP Address Enter the IP address in the field. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Port Range For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields.
PROLiNK® WNR1008 www.prolink2u.com VLAN Item / Function Descriptions / Instructions Enable VLAN Entries in below table are used to config VLAN settings. VLANs are created to provide the segmentation services traditionally provided by routers. VLANs address issues such as scalability, security, and network management. 3.7. Password Item / Function Descriptions / Instructions User Name To set up the login username to protect the Wireless Router configuration accessing via web browser.
PROLiNK® WNR1008 www.prolink2u.com name and password will disable the protection. It’s strongly recommended to assign a set of password for further security. New Password To set up the login password to protect the Wireless Router configuration accessing via web browser. Maximum input is 30 alphanumeric characters (case sensitive.) Confirmed Password Key in the password again to confirm.
PROLiNK® WNR1008 www.prolink2u.com NTP Item / Function Current Time Descriptions / Instructions Enter the current time of this wireless router or click the Copy Computer Time button to synchronize the time with the connected computer automatically. Time Zone Select Select the local time zone from the pull-down menu. Enable NTP client Check to enable NTP (Network Time Protocol Server) client update function.
PROLiNK® WNR1008 www.prolink2u.com Item / Function Descriptions / Instructions Enable DDNS Check to enable the DDNS function. Service Provider Select the desired DDNS Service Provider DynDNS, TZO or Oray from the pull-down list. Domain Name Here shows the domain name of the service provider. User Name/Email Enter your email that you registered in service provider website. (You can refer to below Note information to apply a account form the service provider website.
PROLiNK® WNR1008 www.prolink2u.com Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks. System Log Item / Function Descriptions / Instructions Enable Log Check to enable logging function. System all Activates all logging functions. Wireless Only logs related to the wireless LAN will be recorded. DoS Only logs related to the DoS protection will be recorded.
PROLiNK® WNR1008 www.prolink2u.com Reboot Click the Reboot button to restart the Wireless Router. Version 1.
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 4: PC CONFIGURATION 4.1. For each PC, the following may need to be configured: TCP/IP network settings Internet Access configuration Wireless configuration 4.2. This section describes how to configure Windows clients for Internet access via the Wireless Router. The first step is to check the PC's TCP/IP settings.
PROLiNK® WNR1008 4. www.prolink2u.com Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct. Using DHCP To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. Restart your PC to ensure it obtains an IP address from the Wireless Router automatically.
PROLiNK® WNR1008 4. www.prolink2u.com Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct. Using DHCP To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. Restart your PC to ensure it obtains an IP address from the Wireless Router.
PROLiNK® WNR1008 4. www.prolink2u.com Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct. Using DHCP To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. Restart your PC to ensure it obtains an IP address from the Wireless Router.
PROLiNK® WNR1008 4. www.prolink2u.com Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct. Using DHCP To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. Restart your PC to ensure it obtains an IP address from the Wireless Router.
PROLiNK® WNR1008 www.prolink2u.com 4. Cancel the pop-up "Location Information" screen. 5. Click Next on the "New Connection Wizard" screen. 6. Select "Connect to the Internet" and click Next. 7. Select "Set up my connection manually" and click Next. 8. Check "Connect using a broadband connection that is always on" and click Next. 9. Click Finish to close the New Connection Wizard Setup is now completed. For Windows Vista 1.
PROLiNK® WNR1008 www.prolink2u.com 4.4. To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router as the "Gateway". Ensure you are logged in as "root" before attempting any changes. Fixed IP Address By default, most Unix installations use a fixed IP Address. If you wish to continue using a fixed IP Address, make the following changes to your configuration. Set your "Default Gateway" to the IP Address of the Wireless Router.
PROLiNK® WNR1008 www.prolink2u.com Router. To make a connection, each station must use the same algorithms and pass phrase as the WPA Wireless Router. WPA2 Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and WPA2-Mixed Hex (64 characters). If Hex is selected, users will have to enter 64 characters string at a time. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key : Pre-Shared Key serves as a password.
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 5: TROUBLESHOOTING 5.1. This chapter covers some common problems that may be encountered while using the Wireless Router and some possible solutions to them. If you follow the suggested steps and the Wireless Router still does not function properly, contact your dealer for further advice. 5.2. Problem 1: Solution 1: Can't connect to the Wireless Router to configure it.
PROLiNK® WNR1008 www.prolink2u.com 5.4. Problem 1: Solution 1: My PC can't locate the Wireless Router. Check the following: Mode: Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode) SSID: The SSID (service set identifier) on your PC and the Wireless Router are the same. Remember that the SSID (service set identifier) is case-sensitive. So, for example "Workgroup" does NOT match "workgroup.
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 6: ABOUT WIRELESS LANS 6.1. A group of wireless stations and a single access point, all using the same SSID (service set identifier), form a Basic Service Set (BSS). Using the same SSID (service set identifier) is essential. Devices with different SSIDs are unable to communicate with each other. 6.2. The wireless channel sets the radio frequency used for communication. Access points use a fixed channel. You can select the channel used.
PROLiNK® WNR1008 www.prolink2u.com WPA/ WPA2/ WPA-Mixed WPA/ WPA2 (Wi-Fi Protected Access) is more secure than WEP. It uses a “Shared Key” which allows the encryption keys to be regenerated at a specified interval. There are several encryption options: TKIP, AES, TKIP-AES and additional setup for RADIUS is required in this method. The most important features beyond WPA to become standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable signal latency.
PROLiNK® WNR1008 www.prolink2u.com CHAPTER 7: TECHNICAL SUPPORT 7.1. 7.2. 7.3. Version 1.
www.prolink2u.com SINGAPORE FIDA INTERNATIHIDUPAL (S) PTE LTD Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapataue 339156. Tel : (65) 6357 0668 Email : support@fida.com MALAYSIA FIDA SYSTEMS (M) SDN BHD 29 Jalan USJ 1/31, 47600 Subang Jaya, Selangatau Darul Ehsan, Malaysia. Tel : (60) 3 8024 9151 Email : support_my@fida.com INDONESIA PROLiNK INDONESIA Jl. Cideng Barat No. 79, Jakarta Pusat 10150 - Indonesia. Tel : (62) 21 3483 1777 Email : support@prolink.co.
www.prolink2u.com ® PROLiNK WNR1008 3.75G Wireless-N 4-Port Gigabit Router Buku Manual Versi 1.
PERNYATAAN KOMISI KOMUNIKASI FEDERAL INTERFERENSI Peralatan ini telah diuji dan memenuhi batas untuk Kelas B perangkat digital, sesuai dengan Bagian 15 dari Peraturan FCC. Batasan ini dirancang untuk memberikan perlindungan memadai terhadap gangguan yang membahayakan pada insalasi rumah. Peralatan ini menghasilkan dan dapat memancarkan radio frekuensi energy da jika tidak terpasang dan digunakan sesuai dengan petunjuk, dapat menyebabkan gangguan yang membahayakan pada komunikasi radio.
DAFTAR ISI BAGIAN 1: PENDAHULUAN ............................................................................................................................ 1 1.1. FITUR ........................................................................................................................................................................................................................... 1 1.2. Detail Fisik..................................................................................................
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 1: PENDAHULUAN PROLiNK® WNR1008 3.75G Wireless-N 4-Port Gigabit Router mendukung 4 port Ethernet 10/100/1000M untuk LAN dan 1 port 10/100/1000M interface Ethernet untuk WAN. Dengan teknologi MIMO, dapat mendukung kecepatan transmisi data 6 kali lebih banyak (sampai dengan 300 Mbps) dan cakupan 3 kali lebih dari perangkat IEEE 802.11b/g. Router nirkabel memungkinkan seluruh jaringan Anda berbagi dengan berkecepatan tinggi atau koneksi DSL internet.
PROLiNK® WNR1008 www.prolink2u.com WPS WPS Hijau HIDUP WPS setup berhasil MATI WPS tidak aktif Berkedip Wireless LAN WLAN Hijau MATI WLAN tidak aktif HIDUP WLAN aktif Berkedip LAN Hijau WPS Hijau WLAN data transmit MATI LAN tidak aktif HIDUP LAN aktif Berkedip USB WPS siap melakukan koneksi LAN data transmit HIDUP USB terkoneksi MATI USB tidak terkoneksi Ports dan Tombol (Tampak Belakang) Ports dan buttons Ant. 1 Ant.
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 2: MENGENAI MODUS PENGOPERASIAN Perangkat ini menyediakan aplikasi operasional dengan Router, AP dan Modus Converter yang eksklusif. Perangkat ini dikirimkan dengan konfigurasi yang benar. Jika Anda ingin mengubah pengaturan dalam rangka untuk melakukan konfigurasi lebih maju atau bahkan mengubah modus operasi, Anda dapat SECARA MANUAL beralih ke modus yang Anda diinginkan oleh produsen seperti yang dijelaskan dalam bagian berikut 2.1.
PROLiNK® WNR1008 www.prolink2u.com 2.3. Ketika bertindak sebagai Access Point (AP), perangkat ini menghubungkan semua stasiun (PC / notebook dengan adaptatau jaringan nirkabel) ke jaringan nirkabel. Semua stasiun dapat memiliki Akses Internet jika hanya Access Point memiliki koneksi internet. 2.4. If set to Modus Converter, a device connects to each other through an access point atau a base station (gateway atau router.
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 3: KONFIGURSI 3.1. Step 1. Sambungkan salah satu ujung kabel Ethernet ke port LAN (1~4) dari Wireless Router, ujung yang lain ke PC atau notebook Anda. Step 2. Ada 2 metode untuk dapat terhubung ke Internet (Hanya satu yang dapat digunakan): 2-1. Sambungkan kabel Ethernet ke port WAN (Internet) dari Wireless Router, ujung yang lain ke port ADSL atau cable modem. 2-2. Or Anda dapat menggunakan 3.5G USB card (yang disediakan oleh provider) ke USB port. Step 3.
PROLiNK® WNR1008 www.prolink2u.com Lihat permasalahan dibawah, Jika Anda sulit untuk terhubung dengan WNR1008 Jika WNR1008 tidak merespon Wireless Router sudah terinstall dengan benar, koneksi LAN OK, dan powered menyala. Anda dapat melakukan uji koneksi dengan penggunakan perintah "ping": Silahkan ke Start>Run…> Ketik “cmd” maka akan muncul MS-DOS prompt. Ketik perintah: ping 192.168.123.
PROLiNK® WNR1008 www.prolink2u.com Jenis Koneksi Umum Jenis koneksi The Internet berdasarkan ISP (Internet Service Provider) yang dapat Anda gunakan. Jenis Modem Jenis IP Keterangan Data ISP yang diperlukan Biasanya, tidak ada. Alamat IP Dynamic Alamat IP Anda Your IP address ikan dialokasikan Namun , beberapa ISP mungkin secara otomatis, ketika Anda terhubung dengan ISP. membutuhkan Hostname, Domain name, atau alamat MAC Anda. Cable Modem Alamat IP akan dialokasikan .
PROLiNK® WNR1008 www.prolink2u.com 3.4. Pengaturan Antarmuka LAN 192.168.123.100 255.255.255.0 192.168.123.254 192.168.123.100 192.168.123.200 Item / Fungsi Penjelasan/ Instruksi IP Address Menampilkan alamat IP dari Wireless Router (Alamat Default IP adalah 192.168.123.254) Subnet Mask Subnet mask dari Wireless Router (Default subnet mask adalah 255.255.255.0.) Default Gateway Menampilkan default gateway dari Wireless Router.
PROLiNK® WNR1008 www.prolink2u.com Centang kotak untuk mengaktifkan fungsi Static DHCP, pengaturan default adalah tidak aktif. Bila diaktifkan, pengguna dapat meng Klik tombol Set Static DHCP untuk mengatur fungsi Static DHCP Static DHCP IP Address: Masukkan alamat IP statis untuk penggunaan alamat yang disediakan oleh DHCP Server. MAC Address: Masukkan alamat MAC untuk setiap station, lalu DHCP Server akan mendistribusikan alamat IP statis ke semua station secaa otomatis ketika terhubung.
PROLiNK® WNR1008 Item / Fungsi WAN Access Type www.prolink2u.com Penjelasan/ Instruksi Pilih jenis WAN Access Static IP, DHCP Client, PPPoE, atau Mobile Networks dari menu pull-down. Pengaturan Default adalah DHCP (Auto Config). DHCP Client Jika DHCP Client yang dipilih, router akan memperoleh alamat IP secara otomatis. Hostname: Masukkan hostname untuk menetapkan alamat IP ke computer Anda. Maximum 32 alphanumeric karakter (case sensitive).
PROLiNK® WNR1008 www.prolink2u.com MTU Size: MTU (Maximum Transmission Unit), nilai default adalah 1492 untuk aplikasi Anda. Mengurangi ukuran paket dapat membantu menghubungkan ke situs web tertentu atau mempercepat laju paket transfer. Jika ukuran paket salah dimasukkan, Anda mungkin tidak dapat membuka situs web tertentu. Pilih Attain DNS Automatically atau pilih Set DNS Manually untuk menset alamat IP dari DNS server. Pengaturan Default adalah Attain DNS Automatically.
PROLiNK® WNR1008 www.prolink2u.com Mobile Networks Pengguna harus menyisipkan USB card yang disediakan oleh provider ke dalam port USB pada wireless router untuk dapat menggunakan fungsi Mobile networks. Auto APN: APN (Access Point Name.) Jika fungsi ini dipilih, system akan mendeteksi secara otomatis pengaturan mobile network melalui USB yang disediakan oleh Internet service provider (ISP). Menggunakan pengaturan default sangat direkomendasi.
PROLiNK® WNR1008 www.prolink2u.com Advanced Routing Jika Anda menghubungkan beberapa router dengan Wireless Router, Anda mungkin perlu mengatur aturan routing yang telah ditetapkan agar lalu lintas data lebih efektif yang disebut rute statis antara router dan Wireless Router. Item / Fungsi Penjelasan/ Instruksi Enable Dynamic Centang untuk mengaktifkan fungsi dynamic router. Route NAT: Pilih untuk mengaktifkan fungsi network address translation.
PROLiNK® WNR1008 www.prolink2u.com PPTP Server Item / Fungsi Penjelasan/ Instruksi Enable PPTP Server Centang untuk mengaktifkan fungsi PPTP server, fungsi ini memungkinkan Anda untuk terhubung ke lokasi lain dengan aman memalui internet. User Name Masukkan username, ketika PPTP client mencoba untuk terhubung ke PPTP sever akan menggunakan username ini. Password Masukkan password, ketika PPTP client mencoba untuk terhubung ke PPTP sever akan menggunakan password ini.
PROLiNK® WNR1008 www.prolink2u.com 3.5. Basic PROLiNK_WNR1008 Item / Fungsi Penjelasan/ Instruksi Disable Wireless Centang untuk men nonaktifkan fungsi wireless. Jika antarmuka wireless LAN di non aktifkan, lampu LED WLAN akan LAN Interface mati. Bdan Anda dapat memilih satu modus yang Anda inginkan. Mendukung 2.4GHz (B): 802.11b saja. Mendukung 2.4GHz (G): 802.11g saja. Mendukung 2.4GHz (N): 802.11n saja. Mendukung 2.4GHz (B+G): mendukung 802.11b dan 802.11g saja. Mendukung 2.
PROLiNK® WNR1008 www.prolink2u.com Pengguna dapat mengatur multiple AP disini. Network Type SSID Channel Width Jika mode diatur ke modus AP atau klien bahwa jenis jaringan yang dapat diatur untuk Infrastruktur atau Ad hoc SSID (Service Set Identifier) yang disebut nama jaringan karena pada dasarnya itu adalah nama yang mengidentifikasi jaringan nirkabel (case-sensitif).
PROLiNK® WNR1008 www.prolink2u.com Advanced Item / Fungsi Penjelasan/ Instruksi Fragment Threshold Mekanisme Fragmentasi digunakan untuk meningkatkan efisiensi ketika lalu lintas yang tinggi mengalir sepanjang dalam jaringan nirkabel. Jika MIMO 802.11g Wireless Router sering mengirimkan file besar di jaringan nirkabel, Anda dapat memasukkan nilai baru Fragmen Threshold untuk membagi paket. Nilai ini dapat diatur 256-2346. Nilai default adalah 2346.
PROLiNK® WNR1008 www.prolink2u.com Security PROLiNK_WNR1008 Item / Fungsi Penjelasan/ Instruksi Pilih SSID Pilih SSID (Service Set Identifier) untuk membuat pengaturan security pada menu pull-down. Encryption Ada beberapa jenis modus encryption termasuk Disabled, WEP (Open System), WEP (Shared Key), WEP ( AUTO), WPA (Personal), WPA2 (Personal), dan WPA-Mixed. Pengaturan default security adalah Disabled.
PROLiNK® WNR1008 www.prolink2u.com ACL Item / Fungsi Wireless Access Control Mode Penjelasan/ Instruksi Pilih Allow Listed atau Deny Listed dari menu pull-down untuk mengaktifkan fungsi access control. Pengaturan Default adalah Disabled. MAC Address Masukkan alamat MAC (12 karakter) dari station yang boleh mengakses Access Point ini. Comment Ana bias memasukkan 20 karakter sebagai deskripsi alamat MAC. Current Access Control List Tabel ini menampilkan informasi MAC pada client.
PROLiNK® WNR1008 Step 1. www.prolink2u.com Pengguna ingin menggunakan fungsi WDS, silahkan ke halaman Wireless > Basic untuk memilih modus WDS atau AP+ WDS (Repeater), dan buat AP dengan Network Name (SSID) dan Channel yang sama. Setelah selesai, klik tombol Apply Changes. 1 2 PROLiNK_WNR1008 3 Versi 1.
PROLiNK® WNR1008 Step 2. www.prolink2u.com Lalu pergi ke Wireless > WDS (1) untuk mengaktifkan fungsi WDS dan (2) masukkan alamat Wireless MAC (silahkan pergi ke Status> Wireless Configuration untuk memastikan alamat BSSID) untuk setiap AP yang merupakan bagian dari WDS. Klik tombol Apply. 1 2 Item / Fungsi Penjelasan/ Instruksi Enable WDS Centang untuk mengaktifkan fungsi WDS. MAC Address: Masukkan Wireless BSSID (MAC) 12 karakter dari wireless AP yang ingin Anda hubungkan.
PROLiNK® WNR1008 www.prolink2u.com Encryption: Pilih jenis encryption None, WEP 64 bits, WEP 128 bits, dan WPA2 (AES) dari menu pull-down. WEP Key Format: Untuk jenis WEP 64 bits dan WEP 128 bits encryption, WEP Key Format adalah Hex atau ASCII. WEP Key: Jika memilih Hex menggunakan angka hexadecimal (0-9, atau A-F). Pilih ASCII untuk menggunakan karakter ASCII (case-sensitive). Hexadecimal (WEP 64 bits): 10 Hex karakters (0~9, a~f). Hexadecimal (WEP 128 bits): 26 Hex karakters (0~9, a~f).
PROLiNK® WNR1008 www.prolink2u.com WPS Item / Fungsi Penjelasan/ Instruksi Disable WPS Centang kotak untuk men non aktifkan fungsi WPS, pengaturan default adalah enabled. WPS Status Disini menampilkan status dari fungsi WPS. Klik Reset to Unconfigured untuk me rekonfigurasi koneksi WPS. Self-PIN Number Menampilkan 8 karakters PIN code dari router. Push Button Configuration Client PIN Number Versi 1.00 Klik tombol Start PBC untuk membuat okneksi WPS dengan client.
PROLiNK® WNR1008 www.prolink2u.com Schedule Item / Fungsi Penjelasan/ Instruksi Enable Wireless Centang kotak untuk mengaktifkan fungsi schedule. Pilih hari dan waktu yang Anda ingin aktifkan. Schedule 3.6. DMZ Settings Item / Fungsi Penjelasan/ Instruksi Enable DMZ Centang kotak untuk mengaktifkan fungsi DMZ. Jika fungsi DMZ Host aktif, berarti Anda bisa mengekspose computer di Internet untuk beberpa aplikasi seperti online game , dll. DMZ Host IP Masukkan alamat IP dari host Anda.
PROLiNK® WNR1008 www.prolink2u.com URL Filter Settings Item / Fungsi Penjelasan/ Instruksi Enable URL Filtering Centang untuk mengaktifkan fungsi URL filtering. URL Address Masukkan URL address. Apply Changes Setelah selesai melakukan pengaturan, Klik tombol Apply changes untuk menyimpan. Reset Klik Reset untuk kembali ke nilai semua. Current Filter Table Menampilkan informasi dari alamat URL. Delete Choosed Klik Delete Choosed untuk menghapus item.
PROLiNK® WNR1008 www.prolink2u.com Item / Fungsi Penjelasan/ Instruksi Enable MAC Filtering Centang untuk mengaktifkan fungsi MAC filtering. MAC Address Masukkan alamat MAC dari client. Comment Masukkan deskripsi dari alamat MAC. Apply Changes Setelah selesai melakukan pengaturan, Klik tombol Apply changes untuk menyimpan. Reset Klik Reset untuk kembali ke nilai semua. Current Filter Table Menampilkan informasi MAC filter. Delete Choosed Klik Delete Choosed untuk menghapus item.
PROLiNK® WNR1008 www.prolink2u.com IP Filtering Item / Fungsi Penjelasan/ Instruksi Enable IP Filtering Check to enable IP filtering function. Local IP Address Enter the local server’s IP address. Protocol Pilih protocol (TCP, UDP atau Both) digunakan untuk layanan remote system. Comment Anda dapat membuat deskripsi untuk port range. Apply Changes Setelah selesai melakukan pengaturan, Klik tombol Apply changes untuk menyimpan. Reset Klik Reset untuk kembali ke nilai semua.
PROLiNK® WNR1008 www.prolink2u.com Virtual Server Item / Fungsi Penjelasan/ Instruksi Enable Port Centang untuk mengaktifkan fungsi Port Forwarding. Forwarding IP Address Masukkan alamat IP. Protocol Pilih the protocol (TCP, UDP atau Both) used to the remote system atau service. Port Range Untuk layanan TCP dan UDP, masukkan port awal yang digunakan. Jika layanan menggunakan nomor port tunggal, masukkan nomor yang sama pada kedua kolom. Comment Anda dapat membuat deskripsi untuk alamat MAC.
PROLiNK® WNR1008 www.prolink2u.com VLAN Item / Fungsi Penjelasan/ Instruksi Enable VLAN Masukkan pada tabel di bawah ini digunakan untuk pengaturan konfigurasi VLAN. VLAN diciptakan untuk menyediakan layanan segmentasi tradisional yang disediakan oleh router. VLAN mengatasi masalah seperti skalabilitas, keamanan, dan manajemen network 3.7. Password Versi 1.
PROLiNK® WNR1008 www.prolink2u.com Item / Fungsi Penjelasan/ Instruksi User Name Mengatur username login untuk melindungi konfigurasi Wireless Router mengakses melalui browser web. Nama pengguna password dan Kosong akan menonaktifkan perlindungan. Ini sangat dianjurkan untuk menetapkan satu set keamanan lebih lanjut. New Password Mengatur password login untuk melindungi konfigurasi Wireless Router mengakses melalui browser web. input maksimum adalah 30 karakters alfanumerik (case sensitive.
PROLiNK® WNR1008 www.prolink2u.com Item / Fungsi Penjelasan/ Instruksi Enable Media Server Media Server memungkinkan pengguna berbagi file multi-media pada jaringan lokal Share Folder Name Masukkan nama file share pada LAN. NTP Item / Fungsi Current Time Penjelasan/ Instruksi Masukkan jam pada wireless router atau Klik tombol Copy Computer Time untuk melakukan synchronize. Time Zone Pilih Pilih zona waktu local dari menu pull-down.
PROLiNK® WNR1008 www.prolink2u.com Item / Fungsi Penjelasan/ Instruksi Enable DDNS Centang untuk mengkatifkan fungsi DDNS. Service Provider Pilih layanan DDNS yang Anda suka seperti DynDNS, TZO atau Oray dari menu pull-down. Domain Name Disini akan terlihat nama domain dari service provider. User Name/Email Masukkan alamat email yang Anda register di website service provider. Password/Key Masukkan passwords yang Anda register di website service provider.
PROLiNK® WNR1008 www.prolink2u.com Statistics Halaman ini menampilkan counter paket untuk penerimaan dan transmisi sehubungan dengan jaringan Ethernet dan nirkabel. System Log Item / Fungsi Penjelasan/ Instruksi Enable Log Centang untuk mengaktifkan fungsi log. System all Mengaktifkan seluruh fungsi log. Wireless Hanya logs yang berhubungan dengan wireless LAN yang akan di catat. DoS Hanya logs yang berhubungan dengan DoS yang akan di catat.
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 4: KONFIGURASI PC 4.1. Untuk setiap PC, berikut yang harus Anda konfigurasi: Pengaturan TCP/IP network Konfigurasi Akses Internet Konfigurasi Wireless 4.2. Bagian ini menjelaskan bagaimana cara mengkonfigurasi Windows clients untuk Akses Internet melalui Wireless Router. Langkah pertama adalah memeriksa pengaturan TCP/IP pada PC.
PROLiNK® WNR1008 www.prolink2u.com 4. Klik tombol Properties. Anda akan melihat gambar berikut. 5. Pastikan pengaturan TCP/IP sudah benar. Menggunakan DHCP Untuk menggunakan DHCP, Pilih Obtain an IP address automatically dan Obtain DNS server address automatically. Ini merupakan pengaturan default Windows. Menggunakan cara ini direkomendasi. Secara default, Wireless Router akan bertindak sebagai DHCP Server.
PROLiNK® WNR1008 www.prolink2u.com 4. Klik tombol Properties. Anda akan melihat gambar berikut. 5. Pastikan pengaturan TCP/IP sudah benar. Menggunakan DHCP Untuk menggunakan DHCP, Pilih Obtain an IP address automatically dan Obtain DNS server address automatically. Ini merupakan pengaturan default Windows. Menggunakan cara ini direkomendasi. Secara default, Wireless Router akan bertindak sebagai DHCP Server.
PROLiNK® WNR1008 www.prolink2u.com 4. Klik tombol Properties. Anda akan melihat gambar berikut. 5. Pastikan pengaturan TCP/IP sudah benar. Menggunakan DHCP Untuk menggunakan DHCP, Pilih Obtain an IP address automatically dan Obtain DNS server address automatically. Ini merupakan pengaturan default Windows. Menggunakan cara ini direkomendasi. Secara default, Wireless Router akan bertindak sebagai DHCP Server.
PROLiNK® WNR1008 4. www.prolink2u.com Klik tombol Properties. Anda akan melihat gambar berikut. 5. Pastikan pengaturan TCP/IP sudah benar. Menggunakan DHCP Untuk menggunakan DHCP, Pilih Obtain an IP address automatically dan Obtain DNS server address automatically. Ini merupakan pengaturan default Windows. Menggunakan cara ini direkomendasi. Secara default, Wireless Router akan bertindak sebagai DHCP Server.
PROLiNK® WNR1008 www.prolink2u.com Untuk Windows Vista 1. Pilih Start menu Control Panel Network dan Internet Network dan Sharing Center. 2. Pilih Set up a connection atau network. 3. Pilih Connect to the Internet dan Klik Next untuk melanjutkan. 4. Pilih Broadband (PPPoE). 5. Masukkan User name dan Password yang disediakan oleh ISP, lalu Klik Connect untuk membuat koneksi. Untuk Windows 7 1. Pilih Start menu Control Panel Network Sharing Center. 2.
PROLiNK® WNR1008 www.prolink2u.com Untuk bertindak sebagai DHCP Client (Direkomendasi) Prosedur di bawah ini dapat bervariasi tergantung versi Linux dan X-windows Anda gunakan. 1. Jalankan X Windows client Anda. 2. Pilih Control Panel – Network. 3. Pilih "Interface" untuk Network card Anda. Biasanya, ini dikenal dengan "eth0". 4. Klik tombol Edit, set "protocol" ke "DHCP", dan simpan pengaturan ini. 5.
PROLiNK® WNR1008 www.prolink2u.com Enterprise (RADIUS) WPA WPA2 WPA2-Mixed RADIUS Server: RADIUS adalah otentikasi, authorization dan akuntansi client-server protokol. Client adalah Network Access Server yang keinginan untuk otentikasi link nya. The RADIUS adalah server yang memiliki akses ke database user dengan informasi otentikasi. Setiap stasiun harus mengatur Server RADIUS alamat IP, password dan port yang disediakan oleh ISP anda. 802.
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 5: PERMASALAHAN 5.1. Pada BAGIAN ini mencakup beberapa masalah umum yang mungkin dihadapi ketika menggunakan Wireless Router dan beberapa solusi yang mungkin untuk mereka. Jika Anda mengikuti langkah-langkah yang disarankan dan Wireless Router masih tidak berfungsi dengan benar, hubungi dealer Anda untuk saran lebih lanjut. 5.2. Masalah 1: Solusi 1: Tidak bisa terhubung ke Wireless Router untuk mengkonfigurasi.
PROLiNK® WNR1008 www.prolink2u.com 5.4. Masalah 1: Solusi 1: PC saya tidak dapat menemukan Wireless Router. Periksa berikut ini: Mode: PC Anda di set ke mode Infrastructure. (Access Points selalu bekerja dengan mode Infrastructure) SSID: SSID (service set identifier) pada PC Anda dan Wireless Router tidak sama. Ingat bahwa SSID itu case-sensitive. Jadi, contoh "Workgroup" tidak sama dengan "workgroup.
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 6: TENTANG WIRELESS LAN 6.1. Sekelompok stasiun nirkabel dan jalur akses tunggal, semua menggunakan SSID yang sama (service set identifier), membentuk Basic Service Set (BSS). Menggunakan SSID (service set identifier) yang sama sangat penting. Perangkat dengan SSID yang berbeda tidak dapat berkomunikasi dengan yang lainya. 6.2. Wireless channel menetapkan frekuensi radio yang digunakan untuk komunikasi. Jalur akses menggunakan saluran tetap.
PROLiNK® WNR1008 www.prolink2u.com WPA/ WPA2/ WPA-Mixed WPA / WPA2 (Wi-Fi Protected Access) adalah lebih aman daripada WEP.Menggunakan "Shared Key" yang memungkinkan kunci enkripsi untuk dibuat ulang pada interval tertentu. Ada beberapa pilihan enkripsi: TKIP, AES, TKIP-AES dan setup tambahan untuk RADIUS diperlukan dalam metode ini. Yang paling penting di luar fitur WPA menjadi standard melalui 802.11i/WPA2 adalah: pre-authentication, yang memungkinkan roaming cepat aman tanpa latensi sinyal terlihat.
PROLiNK® WNR1008 www.prolink2u.com BAGIAN 7: TECHNICAL SUPPORT 7.1. 7.2. 7.3. Versi 1.
www.prolink2u.com SINGAPORE FIDA INTERNATIHIDUPAL (S) PTE LTD Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapataue 339156. Tel : (65) 6357 0668 Email : support@fida.com MALAYSIA FIDA SYSTEMS (M) SDN BHD 29 Jalan USJ 1/31, 47600 Subang Jaya, Selangatau Darul Ehsan, Malaysia. Tel : (60) 3 8024 9151 Email : support_my@fida.com INDONESIA PROLiNK INDONESIA Jl. Cideng Barat No. 79, Jakarta Pusat 10150 - Indonesia. Tel : (62) 21 3483 1777 Email : support@prolink.co.
