Installation manual

PS Engineering
PMA6000 Series Audio Selector Panel and Intercom System
Installation Manual
200-066-0006 Appendix C Rev. 6, March 2005
Appendix C Bottom Connector wiring, Mono and Stereo (see note 9)
Com 1 Audio Hi
Com 1 Mic Key
Com 1 Lo
Communications
Transceiver #1
Communications
Transceiver #2
Nav 1 Audio Hi
NAV 1 Audio Lo
VHF Nav 1
Nav 2 Audio Hi
Nav 2 Audio Lo
VHF Nav 2
DME Audio Hi
DME Audio Lo
DME Receiver
Com 1 SPR Load
Com 2 SPR Load
Unswitched Input #1 Hi
Unswitched Audio Lo
Unswitched Audio #1
Unswitched Input #2 Hi
Unswitched Audio Lo
Unswitched Audio #2
Pilot Mic Audio Hi
Pilot Mic PTT
Pilot Mic Lo
C
5
4
2
MM Sense Output
MKR Ant.
B
A
White Lamp Output
Blue Lamp Output
Amber Lamp
MM Sense
RG-58A/U Coax
PA Mute Trigger
F
D
E
18
20
1
Z
W
22
28 Volt Lights Hi
14 V Lights Hi
Lights Lo
Ground Lug
Airframe Ground
2A
11-33 VDC
9
P
R
Com 1 Mic Audio Hi
Com 2 Audio Hi
Com 2 Mic Key
Com 2 Lo
10
H
V
Com 2 Mic Audio Hi
12
13
6
14
N
19
L
Com 1 Spr Load
Com 1 Spr Load
Com 2 Spr Load
Com 2 Spr Load
16
M
T
17
Speaker Hi
Speaker Lo
3
Pilot Phones (R)
Pilot Phones (L)
Pilot Phones Lo
8
Y
To Pin 1
Top Conn.
Communications
Transceiver #3
(HF/TEL)
J
K
15
Com 3 Audio Hi
Com 3 Mic Audio Hi
Com 3 Lo
Com 3 Mic Key
ADF Audio Hi
ADF Audio Lo
ADF Receiver
S
AUX Audio Hi
AUX Audio Lo
AUX (MKR) Audio
11
Notes:
1. All shields should be grounded at audio panel only.
other end remains floating.
2. Speaker and Pilot Headphone ground returns
MUST be kept separate and connected
to pin 22.
3. All Power and Ground wires must be #18 gage wire
4. Pilot mic and headphone jacks must be isolated from ground.
5. PA Mute is a TTL level logic output
that is pulled low when PTT active.
6. Speaker loads may be reqired on some transceivers.
Consult manufacturer's information.
7. 28V installations require 15 ohm, 15W dropping
resistor.
8. All shielded wires must be MIL 22750 or 27500.
9. For mono versions (PMA6000, PMA6000M)
connect pilot headphone to pin 3 with 2-conductor wire.
For stereo versions (PMA6000S and PMA6000M-S) connect
pilot headphone (L) to top connector, Pin 1,
using 3-conductor wire.
10. Key pin between pin 7 and 8.
11. For PMA6000 without marker, marker audio can be
interfaced through pin 11 (aux), and will
appear when M button pushed.
12. Marker Lamp outputs (C, 5, 4) go to +9 VDC, +/- 2VDC
at maximum bright, unlaoded) when active.
13. MM Sense output (pin 2) goes high when middle
marker signal received.
14. Pin T is unswitched, unmuted input
Pilot PTT
See Note 3, 7
See Note 5
See Note 2
See Notes 6, 8
BOTTOM CONNECTOR PMA6000
See Note 9
Com 3 SPR Load
Com 3/HF Spr Load
15 ohm 15W
See Note 11
Ext. Marker Annunciator
Ext. Marker Lamp (Amber)
Ext. Marker Lamp (White)
Ext. Marker Lamp (Blue)