TREE ASSEMBLY INSTRUCTIONS The Oldest Family Name for Christmas Trees in America® SAVE THESE INSTRUCTIONS! -1-
Table of Contents 1. Important Safety Notes Page 3 2. Attention Page 4 3. Getting Started Page 4 Opening the box Page 4 Setting up the stand Page 5 Setting up the tree Page 5 4.
It Took Over 60 Years To Grow This Puleo Christmas Tree, As the “Oldest Family Name for Christmas Tree In America ®”, our mark of quality is on every Puleo Christmas Tree. With proper handling and storage, you will be able to make your tree a lasting part of your holiday tradition. CAUTION: IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS Do not connect extra light sets, tree tops or any other electrical items to the existing light sets on your pre-lit tree.
This product employs an overload protection (fuse) in the plug of each light set. A blown fuse indicates an overload or short circuit situation. If the fuse blows, unplug the product from the power supply. Replace the fuse as per the replacement instructions indicated in this manual (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded.
What’s inside the Box: Metal tree stand, or plastic or resin pot 3 Eyebolt screws (trees with plastic stands or pot bases do not have eyebolt screws) Packet of replacement bulbs and fuses. 2 or more tree sections depending on the size of the tree Now that you have opened the box, you will notice that each section of the tree is wrapped in bubble wrap for protection during shipping. Depending on the size of your tree, you may have as few as 2 sections or as many as 9 sections.
shaped, you can plug it into the wall outlet to illuminate the lights. At this point you are now ready to assemble the middle and top sections of the tree. 4. Tree Lighting Instructions Getting your tree lit is as easy as 1-2-3. You may also follow the tags attached to each section of the tree. Connecting the Wiring Harnesses Now that the bottom section of the tree is shaped, plugged in and lit, you will now need to plug in and shape the next section above it.
Diagram of Tree with 3 sections and 550 lights or less -7-
(Figure 6) Diagram of Tree with 3 sections and more than 550 lights (Figure 7) -8-
Diagram of Tree with 4 sections and 800 or less lights (Figure 8) -9-
Diagram of Tree with 4 sections and more than 800 lights (Figure 9) - 10 -
Diagram of Tree with Low Voltage Lights and UL listed adaptor (Figure 10) - 11 -
5. Shaping the Tree Branches When your tree is set-up, you can shape the branches according to following instructions: 1) Begin with the branches at the bottom of the tree and work your way to the top. 2) Starting at the rear of each branch nearest to the pole, bend 1 tip to the left, 1 tip right, and 2 tips slightly up. Follow this sequence until the end of each branch (See Dia. 1). Note: Some tree models have side branches attached to the main branch stem that require additional shaping (see Dia. 2).
it should be replaced immediately. This will extend the life of the remaining working bulbs. Leaving burnt out bulbs in the light set after a long period of time, will cause a domino effect on the working bulbs. You might even notice the light set burning much brighter. Eventually, all 50 bulbs in the same ring will burn out in and will need to be replaced. Please note that burnt out bulbs are not covered under the warranty. They are considered normal wear and tear and not a warranty defect.
There are 2 fuses inside the plug; if they are black it means that they are burnt out. Replace them with the spare fuses provided with the product. If the section is has an extension cord connection, check the connection between the plug and receptacle to ensure the connection to the receptacle is tight. If all above steps can’t solve the problem, check the fuse in the plug of the extension cord. There are 2 fuses in the fuse case, one is in use, and the other is a spare.
1.) For a period of 5 years from date of purchase, Puleo International, Inc will replace defective parts on the product at no charge. Please note that the customer is responsible for shipping and handling. 2.) This limited warranty does not cover damage resulting from accident, misuse, abuse, negligence or normal wear and tear. 3.) This limited warranty does not apply to Floor Display Trees purchased from a store. 2 Year Limited Warranty on Light Sets on Tree 1.
c) Rotating Tree Stand: Can securely hold a tree that weighs up to 100 lbs. 8. Contact Us We back up our trees with a highly professional customer service team. Email: info@puleointl.